Drove the car, 20 min to shopping, and when I came out the car would sputter and die??!! it happened a few times.. it would crank for really a long time, engine would fire up but sputter & die. I was cussing & let the car sit at mall parking lot for a bit, thinking I'll have to cab home but it started up again after 10 min and drove fine. It happened on a parking lot, not on the highway.
View 24 RepliesAfter about a 40 minute drive I notice this noise from the cabin when I parked. I popped the hood and took a short video. What this is? It's a Golf SE 1.8T. (Video)
View 16 RepliesI have a 1999.5 jetta vr6, the CEL is on (p0102 MAF sensor circuit low or something like that...). When i start it up, it often dies really soon after and until its warm it will idle really roughly. I'll have to start it up between 5 and 15 times... Once its warm and about 190 F oil temp it runs just fine, but still has a slightly rough idle.
I have a new MAF sensor coming in, or if there are any other things i should check that might contribute to the problem.
Normally when cold the car would start and rest at about 1,200 maybe 1,300 for a couple minutes then go down to its normal idle point, recently when starting it when cold, it sounds and looks like it wants to do that but just goes straight to its normal idle point, its only started this a couple does ago and has me a little worried now. could there be anything wrong ?
View 12 RepliesI've got a 2003 Jetta Wolfsberg that is acting up, I'll do my best to describe and outline the steps I've taken with the mechanic to fix the problem,
Occasionally, when starting the car one of two things happens, (1) engine turns over, fires, and then dies. Removing the key, letting the car sit for 30 seconds and trying again usually gets the car started. (2) The car will start but will run VERY roughly (misfiring, sounding like the engine is choking out). Very much like this (only sometimes much worse, usually ending in a stall): [URL] ....
Turning the car off, removing the key, letting it sit, and then trying it again will eventually work, even though it might take a few cycles. Once the car gets running it almost always runs fine from thereon. (There have been a couple occasions where the car has gone into limp mode, even on the freeway. Pulling over, letting it sit, and starting it again almost always fixes the problem. I've not yet been stranded.)
Diagnosis & Steps taken:
I get regular codes for the camshaft position sensor and also for the MAP (Barometric pressure) sensor. Both have been replaced.The MAP sensor and the atmospheric pressure readings are off by about 30 (something like 960 and 990). My mechanic thought that maybe it was an electrical problem, he noted that the two sensors mentioned above share a common ground. He replaced the ground because it looked corroded. This brought the pressure numbers both to 990 and the car ran perfectly for a few weeks.One thought was to splice in a new wire to the MAP sensor, to see whether it was a signal problem, this hasn't been done yet. Another possibility was that there is a problem with the ECM.
I THINK, that the problems began just after having the computer flashed at the dealership two years ago. I'd got a code about an update and so the dealership did this. I don't know whether this could have had any effect on these problems, but the times lined up too well to not mention it.
Okay so I ran my excursion earlier this morning and it ran fine and what have you, and now 6 hours later I got to start it up and it sputters and dies. I start it again and it starts right up but then goes to sputter again and I hit the gas and it didn't respond, the RPM gauge was lingering just under 500 RPMs. I had to hold the gas pedal for about 15-20 seconds before the engine would rev up, it kept doing this till the engine finally warmed up and I drove it up and down my block with barely and throttle and with wide open throttle and it ran fine. With the engine warmed up it started with no problems. I have a 2000 5.4L V8 gas
View 5 RepliesI have a small problem that has been going on for about the last 6 months. It only appears once in a while, and only when I have parked facing uphill for longer than a day or so. Upon first start (cold) after sitting pointed uphill for a day or two, it starts real rough and sputters a bit. Then when I check codes, I always have a pending P0316 (misfire within the first 1000 revolutions) along with a P0306 or P0301. No dash lights or anything.
Since those two cylinders are at the front of the motor, could it be that the fuel is leaking back down the rail and leaving those two injectors dry? It isn't always both cylinders, sometimes one or the other. If this is the sign of something bigger on the horizon, I would like to have a heads up.
I have recently purchased a 2012 facelift Tiguan diesel and it has a running fault. When starting the engine, 50% of the time it starts fine, 50% of the time it starts with a "misfire" and sputters for a short while (5-6 seconds) then stalls. If you Rev it a bit while it is sputtering then it clears the sputter and doesn't stall. It doesn't matter if it's hot or cold. Once it's running fine then the misfire never returns until you shut off the engine and then try to restart. The start stop also fails to cut in and I'm wondering if this could be linked. It had a new battery and alternator fitted a few months ago but a non start stop battery was fitted. This has now been changed for the correct battery but both problems still persist.
View 2 RepliesI have a 95 Volvo 850 2.2 L (non-turbo.) I recently replaced the fuel pump, and filter. Now when I try to start the engine, it turns over and sputters before it dies. I let it sit for about 10 minutes and try again with the same results and the same with a longer wait time due to having to charge my battery. I have checked the fuel lines and they seem to be clear, up to the fuel rail. I also checked the plugs and although they need to be replaced, after sanding and re-gaping them, there is plenty of spark. The plug wires and distributor cap are fairly new, and the points look good. So the only problem I see as logical, is the fuel rail, pressure regulator, and injectors. I have bled the fuel rail at the shrader valve, and I am getting little to no fuel from it. I want to remove the injectors and rail, and check out the regulator along with the rest. But how do I tell if the regulator is good, and what is the best way to clean injectors so they will at least last till I can replace them with new?
View 2 RepliesMy 08 escape (3.0) wouldn't go over 45-50mph Sunday on my way home. The next morning I made it about 2 blocks and the battery light came on and it died. I am replacing the battery tomorrow because it tested bad but believe there is also an exhaust problem. Last week it began making a noise I could hear inside the car only when accelerating. Almost sounded like a small,air plane. The car will start and run now but cuts out and sometimes will Rev up when I press accelerator and sometimes won't. The exhaust pipe gets hot really fast and it and the motor both vibrate we the car is started (more than normal) any clue on where to start??
View 1 RepliesTruck spits and sputters when it starts up..and now it does it more often New spark plugs, new fuel pump and filter New mass air flow. I changed fuel octain and that work for a few weeks and back it spits...... It seems that when I put something new in the truck it runs great for a few weeks and then it starts up again...... I can not find a fuel regulator that fits the one that is on the truck now......so I have not replaced it........
View 4 Replies'99 Intrigue (3.5L) with 65k miles. The car has sporadic starting problems where turning the key in the ignition turns the starter motor and results in one of the following scenarios:
1) The engine does not turn on.
2) The engine turns on, RPMs drop and the engine sputters and dies.
3) The engine turns on with no problems (like this morning).
It does not appear to matter whether the engine is hot or cold.
Reading forum posts of people that have seen similar problems, several different solutions would seem to be in order:
1) Replace fuel pressure regulator.
2) Replace crankshaft position sensor
3) Replace camshaft position sensor
4) Replace fuel filter
5) Replace spark plugs
6) Replace idle air control valve
7) Clean the throttle body
Since I rather not start throwing money at the car by replacing parts one by one until the problem is gone.
I have been having issues with my 2001 sports trac 4x4 v6 sohc fuel in. 132k mileage. The problem is I can jump in and it will start first try, fuel pump is heard activating, idle is rough, feels like truck is about to die, pumping on the gas usually causes it to catch and smooth out......after 10 mins. or sometimes less than that truck starts to sputter, step on throttle it dies faster, sometimes when stepping on the throttle before it dies and a truck is able to rev up and then back to idle and not die.
But most times stepping on the gas when it begins to sputter after running for 10 mins or so causes it to die once it dies it doesn't start back up and when key is turned on and off, no fuel pump activation noise. I have scantool data take off an autel 619 saved to notebook text format. Those are my numbers for the scan tool, suggestions I have gotten so far are vacuum leak, failing fuel pump, bad o2 sensors, bad MAF.......so far replaced fuel filter and cleaned MAF....no difference.
I have had a 2005 f150 v6 5 speed for a little over two years. Got about 153k on it. Last night was sitting in a parking lot idling about 20-25 minutes, went to leave and she started sputtering hard, lost all power and died. Started back up, idled fine, as soon as i put it in gear same thing then the check engine light came on.
View 3 RepliesMy Honda has a strange problem that is vexing my mechanic. While I am driving, the engine spits and sputters and sometimes dies. I try to restart and it starts right up but runs rough. Sometimes it takes a while to start back up. If I wait a few minutes, it will start again and drive fine for a while. Then it will do it again. After it is warm or when it is cold at the start, it won't do it.My mechanic cannot get it to do it long enough to diagnose. The computer is not throwing any codes. I believe it is electrical because when it does this, the speedometer goes crazy bouncing up and down. Electrical problem also may explain why the computer is not throwing any codes. I need to narrow it down because my mechanic is reluctant to start trying things as I don't have a lot of money to throw at this.
View 4 RepliesI purchased a 1990 Jeep Cherokee Laredo at a steal . . . I've already replaced the head gasket sealant. My biggest current concern is the fuel pressure. The car either starts up beautifully or sputters and gurgles for a good 5 seconds before finally idling normally (either occur during cold or warm starts).
The sputtering at start-up has become more commonplace as of late. If I drive away without providing a good three-to-five minute warm-up, the car will drive as normal while applying gas pressure to the peddle, then once gas pressure is no longer applied, the car dies silently; The battery stays on, but all power steering and engine power disappear and the car coast into nothingness. If I allow the Jeep to warm up significantly, it will drive as normal for hours, except for it's struggles to compensate long upward hills.
The fuel regulator has a slight leak. Worse at start-up, lessens up over time. The seal may be improperly seated, but is in physical working condition as I can tell. Spark plugs were replaced. Battery was replaced. Injectors have been tightened. There is a slight oil leak (it seems to move around a bit), but is far better since the Head Gasket was replaced. Could this be a bad fuel regulator or something else that I have missed?
I've stumped the local dealership and their Hyundai Tech Line as well. This is a 2011 Hyundai Sonata with about 50k miles. Also this is my first winter with it so I can't tell you if it's a new issue or if it's always happened in the "cold". This is Northern California so the cold nights are about as low as 30.
On a cold start, after 20-30 minutes the heater sputters out and the lights on the control unit go out. Sometimes it goes back on if I continue driving for 5-15 more minutes; another way for it to go on again is to turn the car off and start it again. The final way to turn it back on (which was discovered the last time it was in the shop) is to gently begin to start the car again (while it's on) and just that slight movement in the ignition cylinder turns it back on.
The sputtering out doesn't actually turn it off completely, just the lights, buttons and knobs stop responding and the heat mostly goes off.
The control unit has been replaced, plugs have been tightened and the ignition cylinder has been replaced.
They've road tested it 3 times and I'm a little tired of having to get a rental car as they claim to not be able to start a new case with Hyundai Tech Line until they have my car.
I have a 2006 Town and Country with the 3.3L V6. The last four times I filled the gas tank the engine spits and sputters after running for 2 - 3 minutes. Sometimes it will even stall out. It will re-start after cranking for 4 - 5 seconds and then runs fine. It only does this right after I fill the tank and doesn't do it again until the next fill up. Thought that I might have water in the tank so I added a bottle of HEET to see if it would cure the problem, no effect at all..
View 4 RepliesTrying to do some trouble shooting on my own as I'm tired of spending $$ with my local "diesel" garage and getting ripped off. To start with, here's my symptoms:
1. Hard (very hard) to start in the morning. Gets harder every morning. Took me 10 minutes of cranking yesterday morning
2. Once it does start it's very loud, seems to run on just a couple of cylinders and lot's of white smoke
3. After about 10 minutes it's able to get down the road but then at about 2300 RPM and above it sputters, low power, and LOTS of white smoke again.
4. Lots of diesel smell, almost like it has a leak but no visible signs of leaking anywhere.
I've done a lot of research and seems to be leading me towards injector problem or in that general vicinity. However, my first step is to try to narrow it down a little more before I start throwing parts at it. So, first question is: what's my best option for downloading codes? I guess I need one that is CAN capable but seems like most of these or either a few thousand $$ or I have to go to something like a Scanguage or Bullydog. I've thought about putting a tuner on but I guess at that point I'm committing to keeping the truck for a few more years.
So, just initially looking for info on diagnostics equipment and/or test that will eliminate the issue(s). Second, need inputs on possible problems based on symptoms listed above that would be great too. Had EGR delete done a year or so ago.
I parked the car.. Came out to proceed but car wouldn't turn on.. No lights coming on.. I think I left the lights on.. But I was only away for like 20 min.. It's a Prius ..
View 18 Replies2001 F350 7.3 ... Below 35 degrees, truck is hard to start. Cranks for a while, sputters, dies. Repeat a couple times, finally starts running rough, surging and loping for 10-15 seconds before it settles down and runs smoothly. Recently had all glow plugs replaced. Next cold start didn't show much improvement (not as bad as sometimes, but wasn't very cold either).
Surfing here and other forums, I see suggestions about letting glow plugs heat longer after WTS light goes out. Some suggest as long as 60 seconds. In the past, I have tried waiting a little while longer after light goes out, or turning key off/on and letting it cycle again. But I've never really timed how long I was waiting.
We're having a warm spell right now, so I can't do much testing. But yesterday morning was about 30. I timed the WTS light and it went out after 10 seconds. I waited another 20 seconds.. about 30 seconds total. Starting seemed a little better than usual, and there was about 1 second of roughness before it settled down.
I need to do more cold weather testing to be sure, but it does seem like it might be better to wait longer than I have been.
On the other end of the scale, I saw a comment that glow plug cycle is dependent on oil temp, and they don't come on at all if oil temp is above 40. Is this correct? If so, is there any good reason to wait to start in warm weather? I'm usually pretty diligent about waiting for the light regardless of weather, but the truck doesn't seem to object if I get impatient and start it sooner in warm weather. If the glow plugs aren't even on, why wait?
Should I just totally ignore the light, and wait for some interval (or not at all) based on a semi-educated guess about how much glow plug time might be necessary for the current temp?