Back in the day with my MK4 I was able to roll the windows up/ down etc with my key fob's lock/ unlock buttons when I installed a program I purchased from ECS.... Is anything like this available for the MKVI?
View 2 RepliesI searched but couldn't find any DIY on how to remove/install the haldex controller. Is it straight forward or any special tools needed? I know its very tight in there?
View 3 RepliesInstalled a used comp controller and now vag-com is giving me the a code:
1 Fault Found
01315 - Transmission Control Module
004 - No Signal/Communication
Freeze Frame:
Fault Status: 01100100
Fault Priority: 4
Fault Frequency: 1
Reset Counter: 138
Mileage: 69085 km
Time Indication: 0
I have taken it off and put it back on, I have cleared that code and re-scanned and still receive it. Have not driven car to see what it feels like as of yet.
So I've been noticing some issues with my 2011 GTI with only 1800 miles. I had some weird drive by wire issues, like the motor holding its RPMs with the clutch in for excessive time, a start up and idle issue (TPS?), my passenger window is very slow (heard that this is common), and now my driver window hesitates and pauses when rolling it down... ERR!
And yes I will take it to the dealer, its just that I live 100 plus miles away.
My dealer is telling me my TMPS Controller has failed. Aside from making sure the wiring harness is securely plugged into it, I'll be looking for a replacement. If the Audi TPMS controller (same part number as the Phaeton except that it starts with a 4 instead of a 3) is compatible?
View 6 RepliesI have an 04 Limited, 4x4, 6.0 PSD. Over the past couple of years I have had a issue with the AC control head inside the cab. Every so often there will be no power to the head but when you turn off the vehicle and restart it comes right back on. It happens about once every 6 months.
View 2 RepliesHave one of at least four different software codes, depending on your version of the TPMS controller. For the old controller (which I used to have, and which is present in, for example, air cooled rig), the coding is 0012339. (There is also 0010339.) The new coding below is only if you have coding 0210390 and possibly if you have coding 0211390. The old coding does not work with my controller, and I do not know if the new coding works with the old controller.
Use VAG-COM:
1. to put the option to turn TPMS on/off into the MFI.
2. to get "inflation info" back into the MFI.
Change the software coding to:
0110390
1. What is the procedure in doing a basic setting for the xenon headlights ('04), what group (i.e. 001, 002 etc.)
2. How come I cannot delete/erase the DTC or error code (Headlight is not adjusted/MIL on, no basic setting.
where the airbag controller is on a 1998 1.8 Passat. I have a fault with the controller and I don't know where it is.
View 3 RepliesWell I have my new 8.5x20 trailer on order that has electric brakes and I'm looking to install a brake controller. I don't like how cheesy all the aftermarket ones look and love fords factory controller and upfitter switches. Looking for info on swapping these in the excursions and had it working? I've looked on the net for this mod and came up with nothing.
View 14 RepliesWhen I went to pick up my new travel trailer yesterday , the brake controller wouldn't work. Trying to diagnose this in the pouring rain is the pits. This was after closing time at the dealer so the shop guys were gone already. The sales manager drove to an auto parts store to get a fuse to try it. Worked!
I've got an assortment of blade fuses on hand, but I clearly need these too, and possibly others. I need a name for this type of fuse.
I recently brought it in for the air bag recall. They replaced both front airbags.
Now they say I need a controller module. Does that mean the air bags won't deploy in a crash?
Are the deployed on impact electrically or mechanically?
I have a Derale 16749 electric fan controller set up had a fan die, went back to a old set up using a fan shroud I made and sable fans being the controller isn't set up to handle the load from these fans I want to just add relays in. Way the derale is set up to the fan is 12v. constant but the ground is also a 12v. until the switch reaches temp. then becomes a ground. I am not concerned with wiring the low side up on these fans just high side.
View 1 RepliesWhere do I plug in a brake controller on a 2008 Ford F-150. I know that it's somewhere behind the dash, but I don't know where?
View 5 RepliesI removed the rear radio controller from the back of the console and installed a power inverter in its place. It fit great and everything went smoothly. I should have known it was too easy... I now have no sound coming out of the rear speakers. I assume there is a way to jump the wires to allow the speakers to work, but I'd need a wiring diagram. Right now I have the controller hooked up and buried in the console, which I guess is fine. It's just annoying.
View 10 RepliesIi have a 2002 Ford Explorer XLT. Some days ago I tried to open truck doors with the remote controller and I couldn't. I put new batteries on it and it didn't work either. So i change for another controller I had (not new but in good conditions) i programmed that control and was perfect for 4 days. Now the new control does the same, it has new batteries and doesn't want to work.
View 3 RepliesSo I have a PCS fault on my 2008 LS460L and brought it to my local Lexus Dealership....They basically insist that the data controller is/may be causing the PCS fault.
In the meantime, I guess the most probable action is to disconnect the data controller and see if the problem goes away.....
2010 Passat.....the driver seat controller started acting up today...it will not raise or lower the seat any longer ....front to back works.....seat angle works.....front of the seat cushion still works...but the seat height no longer adjusts.
View 2 RepliesI am going to be pulling a trailer next week. I bought a raybestos voyager XP controller. I expected it to be plug and play but what I got was four wires. I have heard that there is a plug ready under the dash to plug a controller into directly. I found a gray pigtail with male ends. Is this it? Should I take controller back and get one with the correct plug or is there a harness one can buy or is a stop to my local ford dealer in the future.
View 5 RepliesI don't seem to be able to get my trailer brakes to activate to we're I feel the working as the brakes are applied. I like the trailer to come on sooner and feel the trailer braking a bit more than the truck. I try the slide control and I have to go just about 3/4 of the way to get any braking on trailer. I had same with the 2011 and now the 2013. This a new trailer as was the previous trailer and the braking was the same. Trailer brakes are adjusted. I have it set on 10 as I did on the other truck. The other truck was 2011 and a trailer was a 2012 both new, now this set up is a 2013 trailer and 2013 truck and no difference in the two braking on the trailers. Are they all like that? I have installed brake controllers in my trucks and never had an issue not having enough adjustment for the trailer.
View 14 RepliesI'm in the process of putting a brake controller and 7 pin plug in on my 98 F150 Super Cab, 4x4, 4.6 L with a auto trans. Got the Tekonsha Voyager hooked up to the existing harness under the dash. I have the 7 pin installed out back and thats where my problem begins. The 7 pin harness came with 3 30amp fuses and 2 relays that need to be placed in the power distribution box under the hood. I can figure out where the fuses go but my manual says nothing about the relays. The relays that are already in the box are for things like fuel pump etc.
View 7 Replies