Golf/GTI VI :: Rough Clunking Noise After 034 Density Strut Mount Install
Nov 25, 2013
Setup: WRD Street Advantage Coilover kit. Installed and sit at 24.75" all around. 034 Density mounts and new bearings. 19,xxx mi.
7 weeks ago I installed WRD Street Advantage coils. The install went great, no problems. Drove a week or so and decided to replace the strut mounts with 034's density strut mounts and new bearing to get rid of the creaking sound at low speed. Ordered them and put them on this weekend. After driving it I realized the creaking of the old weaker strut mount was gone. However, I inherited a rough clunking or knocking sound (as if something is loose and moving around), which seems to be coming from my passenger side. This happens at all speeds and not specific to turning the wheel. I unistalled/reinstalled everything in the front 4 times and went through everything with a fine tooth comb, but can't find anything loose. All bolts are torqued to spec.
I even removed the sway bar end links and drove it, still there. So it's not the end links. I also tried using the OEM endlinks which are longer than the ones from WRD to increase the space between the axle and the sway bar, possibly thinking it was hitting and causing the noise. No luck, still there. The only thing I noticed is that with the car on jack stands the strut mount is tight to the body but I still have slight play in the spring and it's perch. Is that normal? I'm assuming under load it's tight again. So the only variable in my situation is the new Density Mounts and bearing, can these cause heightened noises due to the increased heardness of the mounts?
View 20 Replies
Advertisement
I finally decided to take the plunge and go with Stage 2 BFI inserts and mount.
Engine Setup (for reference):
EIP cold air
BFI Stage 2 Inserts and Mounts
Recently replaced clutch to brand new stock clutch
TT short shifter
First off, everything feels great. very solid mounts especially when compared to the spongy stock ones. definitely gets the job done.
Here's my question, is it normal to hear a lot of noise chatter coming from the clutch when not engaged? when my foot is on the clutch it goes away, and when i take my foot off a lot of noise starts coming from it. as far as i know, some clutch noise is relatively normal but I'm not sure if a lot is. also, when i start the car, the starter has a deeper, louder, more pronounced tone to it. not sure if that is normal or not either.
View 3 Replies
I had the struts replaced a few months ago along with the strut mounts and bearings. Since then I've developed a popping and clunking noise from the passenger side spring/mount area. I've greased it and it has quieted it down but I noticed that when the car is not moving and I turn the wheel from lock to lock that very top piece of the strut pretty sure it's called the hat moves along with the wheels while the drivers side does not. What's wrong? Is it something as simple as the nut being to lose or to tight?
View 3 Replies
I hear a a series of "clunks" rather than "rattles" (not high pitched) when driving slow over bumpy roads. The noise is coming from the rear only. I think it is more evident in cold temperatures, but I'm not sure. I'll find out if it ever gets above freezing again in MN. Strut mounts? If so, DIY project?
View 6 Replies
Is this possible? I recently installed raceland ultimos and I get this weird muffled noise from the top of the rear suspension. Took it all apart, cut the bump stops shorter, and lubed the strut mounts. Sound went away for about 10 mins of driving, went for another drive and the sound was back. The next day the weather was warmer and the noise was gone. Should I just get new strut mounts?
View 6 Replies
Was tinkering on my car this morning, and at first noticed one side had a bigger gap than the other. Ok, I really need to change strut mount bushings, no big deal. Then I actually looked closer, and they both have some lean to them, but the drivers side is much more than the other one. Is this normal? I've never noticed any play in control arm bushings or anything. So what could be causing this? I would assume they are meant to sit flat but maybe not?
View 8 Replies
I just installed my brand new coil overs. I went to drop the car from the jack and as it lowered I noticed my strut mount fully popped out of the strut mount housing. I can't even close my hood. Did I do something wrong?
View 1 Replies
I have a set of ST coilovers, installed on my tiguan s4motion they ride great but have noticed clunk noise coming from tight strut and I'm pretty sure it's the pillow mount plate, is there anywhere to get replacements or a better plate? ST website doesn't have them separately...
View 1 Replies
Installed fk coils about 5k miles ago. I replaced the strut mounts and the bearing with new oem. I am not "slammed" by any means but a very mild drop. I noticed the strut caps are raised a little under load, can this be the cause of the clunking sound? The strut cap going down on bumps etc? Or could the strut mounts have already failed. Seems a bit premature to me. I guess I'll have to take it apart and take a peek.
View 2 Replies
So I installed my H&R lowering springs about 2 months ago and I am very happy about the stance, ride, and handling up until about 2 weeks ago. The car always had a bit of a spring clunk coming out of the driver's side strut tower, but it has become more apparent and pronounced over the last few days. I already tightened the strut nut and shock tower bolts, what else is there to check out?
View 14 Replies
My upper strut mounts have been failing after a year (about 12,000 miles, typical highway and local street driving, no off-road!). This seems to have started when I replaced shocks with Bilstein slightly stiffer variety. I also put a stabilizer bar on it at that time. Do you think the shocks are the fault? What else might I look for?
View 1 Replies
I have purchased an UltraRacing strut bar for my hyundai accent 2005... The problem however is that my intake manifold sits higher than the throttle body and as a result of this i am unable to mount the bar... The bar has been made for an 03 accent but all points are identical, the only difference that i was able to see is that in the previous accent the throttle body was NOT plastic and sat FLUSH with the throttle body, whereas mine IS plastic and does NOT sit flush with the throttle body.
View 1 Replies
I recently got an MK7, coming from a MK5, and I installed the VWR springs 8 days ago. Since then I've noticed an intermittent clunking sound coming from the rear suspension. I installed springs on my MKV without any issues and again on several other cars, soIi'm familiar with the process. Everything was torqued to spec after the install.
My best description of the sound would be a clunk, not any rattling, clicking, or squealing. The sound is greater in the passenger side rear than the drivers side rear. No issues with anything up front. Sometimes it occurs when I'm turning the steering wheel while backing out of parking spots and driving slowly, other times when I hit bumps in the road, but it is not constant nor does it seem dependent on the size of the bump/pot holes in the road.
What may be causing this? My plan was to give it a week for everything to settle before I tore everything apart to look for any culprit.
View 1 Replies
I have a rear rattle that I cant figure out had the wheel off and levered and pounded on links bushings etc. How can I access the top strut mounts to check them? Nothing found on youtube. Original struts on rear show no leaks or broken spring. Bouncing car does nothing neither does grabbing the tire at 12 and 6 or 3 and 9 position.
View 3 Replies
I have had the LF strut mount fail three times in the last three months. The strut has pushed through the upper mount. The guy a bought the car from said he had the struts replaced about a year ago. Could it be a bad strut?
View 1 Replies
I have to replace the torque strut mount in my 2008 Avalon XLS V6. I can't find the torque specs for the two bolts in my Haynes manual or at any online sites. Also, should I use either threadlocker or anti-seize on them?
View 1 Replies
I had my ST coilovers installed a while back. I love the ride, but a really annoying squeaking/groaning sound developed several weeks ago from the front strut mount area. The noise is heard at low speeds as I roll down the road (most likely high speeds, too) and sounds like its coming from both sides of the upper strut mount area. If you lift up/push down on the car, you can also hear the sound.
I purchased a set of 034 Density upper strut mounts from AMI Motorsports in hopes of eliminating the sound, but the sound got worse!! I still do not have a resolution. At this point, I'm thinking about putting the stock strut mounts back in, as the sound wasn't near as bad with the OE mounts in place.
I've lubricated the sway bar bushings and installed shorter end links (thinking the sound may be sway bar related), but the noise is still there. I even disconnected the end links all together - sound is still there. Could this be faulty coilovers? I tried to file a warranty claim through ST - they don't think their strut is faulty, and even if they did, I'm having a hard time with warranty coverage (long story). If it's the struts, then why did the sound get worse when the new 034 Density upper strut mounts were installed? Could it be faulty mounts?
At this point, I think it's either the mount or the strut, as I did not experience any issues prior to the coilovers.
View 24 Replies
I have a 1999 cadillac Deville that my mechanic says needs a new front strut mount. My symptoms are mostly in cold weather a very slight groan when parking the vehicle or turning into my driveway. It seems like it happens when the steering wheel is on its return back to center and it can be felt slightly in the wheel and heard as the sound a zip tie makes when pulled together with a slight groan. The car has been recently aligned and rides pretty good but sometimes can be a little noisy over bumps.
View 6 Replies
I ordered a stock, LE spoiler to spice up my base model Camry. I read that it's installed through the factory mounting holes although, when I took off the interior trunk lid cover, I did not see any "existing mount holes". It actually looks like a tight squeeze/fit to get any type of tool to drill out or ratchet any mounting bolts down.
View 5 Replies
So I've had this WAAG brush guard laying around for a few years and figured it was time to do something with it. Of course it was bought with no mounting brackets. I had found a lower gear from a Fisher MM1 plow. Tossed the in the truck and started from there.
Broke out the cherry picker and started lining stuff up. Drilled some holes and bolted it up. It's all bolted up but I still need to take a piece of 2x3 angle and weld it to the lower plow mounts to tie the bottoms together and create a step.
View 2 Replies
I had my friend of mine who is a mechanic change my struts out this weekend. I had clunking noises from the right strut Toyota and also a tire place said I needed new struts. So I got them replaced now both sides are clunking see the YouTube video.
View 7 Replies
