2012 GTI. DSG My airbag was blows, so I replaced it. Now im getting the following code.
18036 - Powertrain Data Bus
P1628 - 000 - Missing Message from Steering Angle Sensor
Can the sensor go bad after the airbag was blown? All the steering wheel controls still work.
I've tried to do my due diligence searching on this (I've seen many posts but most have other codes).. I have the P000A code, reads as follows-- Intake (A) Cam Position Sensor Slow Response (powertrain).
I have no misfires, hesitation rough idle, nothing. I have 94k miles and I always done my oil changes @ 5k intervals and I have not had any prior engine maintenance done to the car....
I took my R32 to the local VW dealer today and they are saying they believe it might be the time chain tensioners. I am wonder if this could be a simple sensor issue since the car runs perfectly fine, I just get the engine light coming back on after 1 to 2 weeks of clearing the code. I have had this issue since January and I thought it might be the cold weather here in WI.
I have a fault wit the steering angle sensor, fault code c1231, I have replaced it twice now, the fault would go after installing recon steering angle sensor but would come back again after, not sure what the problem is, looks like they become faulty and dead.
View 1 RepliesI have a fault wit the steering angle sensor, fault code c1231, i have replaced it twice now, the fault would go after installing recon steering angle sensor but would come back again after, not sure what the problem is, looks like they become faulty and dead.
View 4 RepliesI put in a new sensor to stop the problem but now I have the code 00778 which is steering angle sensor and then says 005 no or incorrect basic settings/adaption. I went through the Ross-Tech site to reset the code in group 60 and activate the basic settings, but I am then told that group 060 is not available. I have tried to set the steering wheel angle straight but the angle still says its at 349.47*. My car is a 2004 Jetta GLI 1.8T.
View 4 RepliesJust replaced the steering angle sensor on my Passat. Had a persistent fault that was causing a parking break warning light. I took pictures as I was putting it back together. [URL] .....
View 1 RepliesI know it's on the steering column but is it down near the floor or on the engine compartment side?
View 4 RepliesSo the saga of getting my 2006 Phaeton fixed after an interaction with a deer continues ..... The car has been put back together and fixed, but now there is a new warning light linked to the steering wheel angle sensor.
View 10 RepliesGetting one of those CEL error codes P000A Powertrain on my R32. I used my cheap OBDII bluethooth readers.
Taking it to local shop tomorrow, but they want $109 to scan the car with there VW OBDII scanner.
Why can that scanning be a free charge
P000A/000010 - Camshaft A (Bank 1 Intake): Positioner Slow Response
Possible Causes
* Camshaft Adjustment Valve 1 (N205) faulty
* Wiring/Connectors from/to Camshaft Adjustment Valve 1 (N205) faulty
* Intake Camshaft Adjustment (Bank 1) faulty
Possible Solutions
* Check Camshaft Adjustment Valve 1 (N205)
o Perform Output Test
* Check Wiring/Connectors from/to Camshaft Adjustment Valve 1 (N205)
* Check Intake Camshaft Adjustment (Bank 1)
o Perform Basic Setting
o Check for Tightness of the Adjustment Mechanism
o Check Engine Oil Pressure
I have just replaced the abs ecu and have cleared the codes, thought all was gonna be good but now two code are still coming up they are:
01044 Transmission control module - incorrectly coded
00778 Steering angle sensor-G85
Right around Christmas. Hubby used the code reader and found this:
U059E - Invalid Data Received from NOx Sensor A
And then cleared it. CEL went away and hasn't been back since, so my question is, am I safe? Was it a fluky reading on a cold day of making short errand runs? Or did I have an actual problem even though the CEL has not come back? Truck is running fine, no issues (knock on wood), and I'm not really worried - just curious more than anything.
The code the R threw was p0606 which is the Powertrain/ Engine control module? Where these components are in my R? Or how I can go about trouble shooting this problem?
View 9 RepliesI have a weird question about the nice gti steering wheel. I noticed it some times ago on my old 2008 rabbit too and didnt really cared much when I saw that on the steering wheel of the 2010 gti. Did you noticed that the SW angle isnt good from a top view, I means, when u look at it carefully, did you noticed that the SW is more prononced to the right side, it easier to notice it when u look from a top perspective view of the SW. When u use 2-hands on the SW, u can notice that your left-hand is closer of you that the right-hand. Why Volks designed it like that way?
View 3 RepliesI just had my Prius C in Alignment shop, and after alignment was done I got ABS light ON. We checked it and it says Steering Rack Angle Fault.
View 10 RepliesI have an '06 F350 dually with a 6.0 diesel. I bought this used about 5 years ago and for the most part have loved it. i would always smile on the inside when i heard people bash the 6.0...i thought i got lucky....until today.
140k miles. recent oil change. all is swell...until this morning. Stick in key and turn it. glow plug indicator comes on...all lights come on for a few second....wrench, abs, dtc etc....wrench shuts off...glow plug light comes on...4 or 5 seconds later wrench light comes back on....turn key and NO CRANK.
All fuses are fine...starter cranks if i jump the solenoid...but it won't start. Miles to empty and everything else is just dashes hit the OBD and it says "engine sensor data error"/ "trans temp error" ...
When I use the "scan" feature of my Scangauge II, sometimes the DTC code and/or freeze frame data will change on me. That is, I check it and it says "1 stored code" (without clearing it), then go back to "Gauge" and then check the scanning function again, sometimes the code has changed to something else! With the freeze frame data, sometimes it will even change as I'm scrolling through the different data fields. Very disconcerting....
View 3 Replies[URL] ..... I had the P0430 code come up in my 06 GS300 AWD so i changed both passenger side 02 sensors. i followed the above instructions on changing the pre-cat sensor, changed my 02 sensor plugged everything back up and the P/S light came on and i lost power steering. I unplugged and checked everything at least 10 times until i finally gave up and gave it to lexus today. been about a week though driving without power steering. I know I did everything right and plugged everything snug. Did my P/S just decide to die?
View 6 RepliesI've been trying to get my music from iTunes to an SD card so I have some traveling music for the long drive home. All the files transferred to the card and I can play them on my MacBook pro, but when I put the SD card into my '10 TDI Sportwagon (which has an SD card slot) the radio says the card contains no data. I tried both a 32gb and a 8gb card. For both cards, the radio says the card contains no data.
View 8 RepliesI have a mk4 r32 with 110,000 miles and I'm throwing a p0016 code witch I believe is cam position sensor my timing chains and guides were changed at 90k car runs good and if I erase the code it doesn't come on right away maybe every 200-500 miles:confused could this just be a bad cam sensor there is also no oil leaking from them and they are tight.
View 14 RepliesNeed to diagnose an issue with my 2012 GTI its got 39,000 miles its stage 2 Unitronic tune. So I was driving like an idiot coming home one night and i jumped a set of train tracks. Bent my plastics a little and when I cranked my car the next day my CEL was on. I noticed my intake was much noiser than usual. My buddy checked the code and said i needed a new mass air flow sensor. We replaced it and my CEl came back on within 20 minutes of replacing the sensor.
View 5 RepliesI bought this 01 jetta vr6 and now the abs-asr light is on. hooked up my obd II and it said no data. i have two questions first are there different scanners just for Volkswagen and the next can it be reset for testing?
View 4 Replies