Golf/GTI VI :: Clutch Would Slip And Then Bang While Engaging After Raining
Aug 11, 2012
Today I parked my golf on the street and it was raining, when I came back to the car after four hours the street had flooded and water was about an inch below the bottom of the door on the driver side, and about an inch (or more) on the passenger side and up to the bottom of the exhaust pipes in the back.
The car started fine, but when I began to drive it the clutch would slip and then bang while engaging. Once I had taken off a few times gently everything smoothed out. Car drives fine and the engine bay was dry when I got home (a 40 minute highway drive). NO water got inside the car at all, so the interior was completely dry, every thing appeared to function perfectly. My question is, assuming just the bottom of the motor, trans, and undercarriage got wet is there anything I should be weary of? Any sensors or electrical things down there? Lights, ac, door locks, everything is working and running fine and dry at this point.
View 3 Replies
Advertisement
I have a 2005 VW jetta 2.0 engine 5 speed. Just replaced right control arm spark plugs wires and coil pack. I had a misfire only when it rained and it got rid of it! Driving home in stop and go traffic and My car stalls out a hear a bang and my clutch pedal drops to the floor. I had noticed some fluid loss but nothing was low I checked everything before I left work. I finally get it towed but I can not shift to first I can shift to 2 3 4 5 and reverse. I was in first when it stalled out during stop and go traffic while it was in first gear and i had the clutch pressed in. Everything Ive google says it is more than likely the Slave cylinder that is right below the air box. I found some that said it could be the release bearing in the gearbox for the tranny...
View 4 Replies
So long story short, my clutch is not disengaging all of the way, but only sometimes.... I have replaced clutch, flywheel, slave cylinder, new stainless steel clutch line and new clutch master cylinder all within this month. The same issue has been occurring prior to replacing all of this and also after replacing all of this. I've bled the system (with a power bleeder) more times than you can count on both of your hands so there is no way there is air in the system.
More details : The clutch doesn't slip in any gear. Stop and go traffic in first gear is really the only time I notice it not disengaging. I can't pull it out of 1st gear when it happens so I have to shut the car off to get it out of first gear. When it's stuck in first gear with the clutch pushed in (on a flat surface) and I let off of the brake the car creeps forward. Not at full speed like if I were to release the clutch pedal all the way but its still semi engaged enough to make the car move.
Replacing everything theoretically should have fixed all issues, but it hasn't. The only thing I didnt replace was this piece of the factory clutch line.
Tomorrow I am going to take the stainless steel clutch line and run it straight to the clutch master cylinder bypassing that weird silver box and hope that fixes it. As a side question what does that silver box do anyways?
View 12 Replies
Looks like my clutch is starting to slip a bit at ~50K, after a good bit of HPDE track usage over the last few years, and maybe some poor shifting by me. Anyway, want to replace with a stronger aftermarket unit that can stand up to track events, and am planning to go with a lightweight flywheel as well.
View 4 Replies
I have a 2010 gti with stage 2 tune, and mk6 clutch starting to slip? i have 30,000 miles, i am starting to do my research on the clutches. I am also looking in to just replacing the clutch disk, and i am wondering it just the clutch disk will hold up?
View 24 Replies
I have a 2012 GTi. I just got the stage 2 unitronic flash on my car and now my clutch slips bad. I know i will need to replace my clutch. It was starting to slip before the tune and now it just cant handle it. The shop I went to recommended a South Bend Stage 2 Clutch kit (single mass). Its a daily driver and want something that will last and hold up to 325ftlbs of torque. I do think i want to go with the single mass clutch though.
View 13 Replies
My mother In law's a/c is not working. Last year I replaced the compressor, fcm, and pressure sensor and nothing. Well fast forward a year and I'm here again trying to sort it out. I unplugged the connector to the compressor and there is 2 black wires 1 wire has 6 volts (not 12v) and the others reads nothing. When I turn the A/C on the fans do come on.
View 6 Replies
Driving home yesterday and the ac wouldnt come on my 2003 golf. Worked fine day before. All fuses are fine. Small fan works but large one needs to be replaced but its been that way. Ac button works fine too. What else would cause the clutch to not engage? I believe the pressure is fine as it worked fine the day before.
View 3 Replies
I'm just over 45k miles, have a new mechatronics unit as of 39k, and I am beginning to see a new symptom for the first time since the replacement.... wondering if any of you have experienced this.
It's happened 2 or 3 times in the last couple weeks. The symptom suggests the clutch is not fully engaging. It is as if I had the clutch pedal in while in first gear, and I am feathering the clutch. This happens in "M" mode -- but I basically only drive in M so cannot say if it may happen in D or S.
Today, for example, I was at a red light on an incline. Light turns green, right foot off the brake and onto the throttle. Engine free spins up to nearly 4k and the car hold its position on the incline, without any movement or even a hint of movement. But there apparently was enough force going to the wheels to keep the car on the incline.
The engine does not rev as if it is in LC mode. It is free revving without any sound of it being under load.The clutches seem ok, this is not a clutch slippage problem. It's something occurring in the DSG's control.
I called my service advisor and he looked me up and said I have the latest and greatest MU, and my VIN does not qualify for the recent MU recall that is in the works. He said to just keep an eye on it for now (of course)
View 18 Replies
Exactly what the title says.....when its cold out/cold start....engaging the clutch pedal it makes a click sounds up top of engagement?
View 6 Replies
Here's the story: was on my way downtown last night to get a new suit (I'm in Savannah, GA so it's hot) and AC was working great. The Jetta (2003 AWP) is a stock-everything-1.8T that has never had any AC work done to it from the day I bought it new. I figured it was doing just fine so just leave it alone. Anyway, leave the suit shop (bought a gray three-piece) and go back to the parking lot, start up and get ready to leave, no cold air from the vents. I get it home and do some reading on here and also in the Bentley manual and get into some preliminary troubleshooting. Here's what I have so far:
- Engine running/AC button ON/Blower on "3"/Recirculation OFF/Engine at operating temperature
- Turn blower ON - visually verified that clutch is not engaged and compressor is not spinning
- Shut car off, compressor does turn by hand easily
- With AC button on and blower on, passenger side cooling fan (behind radiator) is ON but driver side cooling fan IS NOT on - I think this indicates a problem from what I've read
- Checked cabin fuses 5, 16, & 25. All have low resistance (good continuity) and are not discolored. Just to make sure I scuffed the contacts with a scotchbrite pad and reinstalled them
- Same deal for the top-of-the-battery power distribution block. All fuses checked okay and were scuffed and reinstalled
- Moved on to the pressure switch/pressure sensor. My vehicle has the 3-pin sensor so jumping contacts is not a possibility. I need to rent/buy a duty cycle meter to check it. Any good tutorial on how to do this? Do I disconnect the connector and check it right at the switch or must I break out the wires and check it in parallel with the connector attached to the sensor?
- I grabbed a flat-head screwdriver and gave the high-pressure and low-pressure service valves a poke and got a good blast of pressure from them so I don't think the system is empty.
- Did a little more reading and found I needed to check voltage at the 3-pin connector on top of the battery power distribution block. I did this with the key ON - no power at any of the pins. Repeated with key ON and engine running with AC button ON and blower ON - still no voltage. For these measurements, the connector was DISCONNECTED. Does this matter? Do I need to have it plugged in to get voltage there (i.e., read the voltage from the rear of the connector with it installed?)
- Finally, and perhaps most enlightening, I suspected I may simply be low on R134a so I bought a can with a pressure gauge on it. Connected it to low-pressure side with engine running, AC button ON, blower on "4", recirculation OFF. The gauge read ~150 PSIG. Yes, this seems high to me too; however, the compressor is still not turning at this point. Does it need to turn to get a good pressure reading from the LP service valve? I recall from everything I read that if pressure is too low, the clutch won't engage, and if pressure is too high, the clutch won't engage
So, as far as I can tell I have a few problems...
1. The driver side fan doesn't run when AC button is ON
2. No voltage at the 3-pin connector on the battery power distribution block Incorrect methods...there is voltage there.
3. Low-pressure side of the AC system is too high Called and checked with a local mechanic...I won't receive correct pressures if the compressor is not turning.
My next steps are to check the voltage at the compressor connector for 12VDC. I suspect I'll get 0V because it's clearly not turning. I'll do this once I can figure out how to get the dang connectors apart without breaking them. 11-year-old heat fatigued plastic is brittle...
Finally got the compressor connector apart.. there is 12VDC on pin 1 and 0VDC on pin 2 (it's a ground, so there shouldn't be..ground continuity check good). Ohmed out the clutch...from what I can tell, that circuit is open. However, I am not 100% sure I was on the contacts because of how the connector is positioned. I'm going to get a dummy connector from a salvage yard and connect it up and make sure I have good contact before I call it a bad clutch.
View 9 Replies
I got my R32 back 2 days ago after deploying to Iraq for a year. Upon driving it for the first time I took it a little easy on the car. I made sure the clutch was fully out before I did anything silly and what not.
Today I took it to the track and on the first launch I dropped it from like 3500 rpm and the RPMs shot up to 7500 and the car was moving at like 5 mph. I hit second gear and the rpm almost instantly shot up to 7500 rpm's again with the car moving at like 10 or 15 miles an hour.
After that, i let off completely. I tried one more time out in the warm up area to see what the hell was going on. Did the same thing. I could smell what I'm guessing was clutch burning pretty freaking bad. I'm, not 100% sure it was the clutch because I've never smelt a clutch smell that strong before.
View 24 Replies
So i just took my 2010 Golf 2.5 into the dealer because it was not going into gear. Its a 5 speed with 12, 900 miles. They tell me they have to pull the trans and open it up before they can even tell whether or not the problem is covered under warranty!
View 16 Replies
Lately I've noticed that when slowly engaging first or reverse, the clutch has noticeable but not loud chatter, kind of like its gargling a little. I JUST changed the trans fluid from OEM to Amsoil 75W-90 API GL4 and its about the same time the noise came, but I'm not going to assume right now that this is the source of the noise. Clutch acts just the same, apart from this gargle.
Might be worth mentioning that this all seems to have started about the same time the temps around here started to dip below 30 on a regular basis
View 9 Replies
Got a weird issue that I've never encountered before. I tried searching but you can't search for just "A/C", so the search was pretty generic and I couldn't find anything similar to my issue.
Hot or cold, doesn't matter. When I turn the A/C on the clutch try's to engage and slowly starts to spin with the pulley until until it finally engages then the a/c will blow out cold air just fine. Also noticed a burning smell coming from it.
01 Jetta 2.0
View 2 Replies
The other night I threw an EPC light. I've tried reading older posts but haven't found anything.
I was at the top of a hill, slowly engaging the clutch while accelerating. I wasn't trying to floor it or anything. My car immediately went into limp mode and the EPC light came on. I pulled over, restarted the car, and it went away. It happened again the next day in the same place.
I am only having the problem on a steep hill while engaging the clutch. Other than this situation, the car seems to be running fine. The car is completely bone stock. I don't have a VAGCOM and can't really afford to purchase one at the moment.
View 1 Replies
For the past few months, pretty consistently, whenever I engage the clutch from full stop into first gear (it does it when starting in second gear too; and reverse) there is a pretty obnoxious and loud screeching noise that I would liken to a subway/train braking or just metal on metal grinding situation. When I took the car in to Douglas for an oil change and APR Stg 1 flash, they told me it's just the brakes being cold, etc. After driving the car some more, I really doubt that it's the brakes and I can reproduce this regularly by slowly releasing the clutch and get the noise usually just before the gear engages.
That car has just over 16K on the clock and has never been abused. The clutch pedal feels fine and there is no issue shifting into any of the gears other than the noise. No mods other than the APR Stage 1.
View 16 Replies
What are the symptoms of the clutch slip.
View 2 Replies
Noticed recently that my clutch is starting to slip. It only seems to happen when I'm cruising in 6th and floor it. When the boost spikes, the revs will shoot up ~750 rpm and then settle back down before the car starts to pull. It is chipped Unitronic Stage 2 with some other bolt-ons.
What I'm wondering is, should I just drive it like this until it really starts to go, or should I replace it now? And what are my options for a new clutch? I don't want to big turbo this car, so the most it could get is a few more bolt-ons. I'd like a stock feeling clutch.
View 8 Replies
I have an '08 Chevy Cobalt with manual transmission with 55,000 miles on it. The clutch is beginning to slip, and is probably going out. What is the life expectancy of a clutch, I thought this seemed kind of short.
View 6 Replies
I have a 13' GT with an automatic trans and 15,000 miles.
While getting onto the highway yesterday I was in D (not + -) and I was probably in 4th gear and hit the gas pedal maybe 60-70% down and my rpms shot straight to 6-7k but I didn't get any acceleration. I let the rpms drop and it drove fine after. Pretty sure I was smelling burnt clutch too (kind of unfamiliar with that scent, I've never slipped a clutch before).
I should probably take it to the dealer for them to look at it, but am worried it will be a 1-2 week thing and I'm not sure if I'd get a loaner.
View 2 Replies
