Golf/GTI VI :: Clutch Pedal Is Losing Pressure / Stuck At The Bottom And Refuses To Bounce Back
Mar 31, 2014
Just a heads up to all MKIV GTI owners out there, new and old. If you feel like the tension on your clutch pedal is deteriorating get it checked earlier rather than later. Because if the slave cylinder malfunctions and leaks you will be faced with a big repair bill due to the fact that the slave cylinder is located inside the tranny. Secondly because of this design, which I think is very stupid, it leaks onto the clutch assembly and can get on your clutch plate. At that point you should replace the clutch plate to prevent any further damage that might be caused by slippage. The clutch plate should not come in contact with any fluids or it will compromise the functionality.
View 2 Replies
Advertisement
I have a 1995 F150 with the 4.9L and it has 73000 miles on it. One morning recently (it was about 35 degrees outside) I went to start my truck to let it warm up. When I let off of the clutch it stayed on the floor. I shut it off and drove my car to work instead. I asked around at work and one guy mentioned that it was probably my clutch master cylinder...so that day we replaced it, and bled it until it felt like knew. Since then, we have had to bleed it three more times, because the pedal keeps losing its pressure making it harder to shift. I have inspected around the clutch line and the bellhousing for signs of needing to replace my slave cylinder, but everything looks fine.
View 8 Replies
1998 Passat 1.8T FWD. My clutch pedal is stuck to the floor and wont spring back up. I can't seem to find the little tank to check the clutch fluid. I have heard the it uses the same tank as the brake lines do, but the tank that holds the brake fluid is full. Can it be the slave cylinder is gone? or just got a air pocket in the line?
View 1 Replies
So this has happened a few times pedal drops with no back pressure then give a bit pull it back up by hand and it's fine has happened 4 or so times in the last year. I'm reluctant to replace slave and master cylinders could it be anything else? 87 Ford F-150 hydraulic clutch
View 10 Replies
So over the weekend my clutch pedal stuck to the floor 2 times and would not come all the way up on several occasions. It has since then stopped doing it. I am wondering if I should bleed my clutch or not. Flush and change fluid?
Just concerned it may turn worse.
View 16 Replies
I just finished installing a new clutch kit on my 2003 Jetta Wolfsburg Edition 1.8 and I have absolutely no pressure on the clutch pedal, I am pretty sure I installed everything correctly. How do you bleed the clutch lines, how do you know if the slave cylinder is bad. When i push the clutch pedal it just goes to the floor with absolutely no return.
View 4 Replies
I have a 2003 Jetta GLI. Thus morning driving into work my clutch pedal stuck to the floor. I was able to pull it back it and make it to work, but when i got to work i noticed fluid dripping from underneath my car.
View 4 Replies
Today I faced another problem i just try to start my car but, due the dead 12v battery it didn't start so i pressed the BRAKE PEDAL until it reach the bottom, again i tried to press but its not going to the bottom why was that, is it due to dead battery? And last time i called an automobile expertise to jump start my car. They check the voltage with a digital multi-meter and he said me if you jump start even you will get this problem again until u replace the new battery. but i said him it doesn't matter do a jump start and finally it was ok . Now again I faced the same problem and this time i am going to change the battery.
View 1 Replies
So I have a 2004 Jetta 1.8t. Recently I noticed an issue with the brakes. It is a rare occurrence that this issue happens. Maybe 1 out 6 times I slowly stop the brake pedal seems to put pressure back against me applying brake pressure and makes somewhat of a grinding noise and the brakes don't seem to grab as well. But a split second later the brakes return to normal and grab as expected. Could it possibly be air in the brake lines or something totally different?
- Front brakes are in excellent condition.
- Just replaced the driver side front abs sensor and put new rear brakes and rotors on.
View 1 Replies
Here's the story and unfortunately no happy ending so my VW started rubbing on the front right side a lot, causing my tires to rip on the front right end. After a while of sitting in the garage i finally decided to go and get a new tire for the car
on the way to the tire shop i noticed some very weird squeaking, i figured it was from the spare tire but it continued even on the new tire. That same night heading to the gym, the R started jerking while driving, almost as if i was pressing the brakes while driving
eventually the car just locks all the tires out of no where, i barely manage to pull into a side street and i could not even make it more than 4 feet from the curb forward. A friend of mine stopped by that saw me, he pulled a cable that seemed to have been wrapped around my axle, said it might of been causing the problem. As i drove away, maybe half a mile more, the car locks up entirely again, this time unable to even get to the side of the street it locked up completely in the middle of an intersection. now here is where it gets really strange. Even in neutral the car refuses to go forward, it was on a hill, in neutral and the car refused to move. So i attempted to push it a little, in drive, i pushed on the gas. it almost feels like the car is setting up for launch control, like the brakes are being held down and it moves about 6-10 feet and grinds to a halt, same in reverse. It took us almost 20 minutes to get it up on a trailer and another 20 to get it into the garage just going 2 steps forward and 1 back the whole time.
I have heard anywhere from transmission to drive train, to transfer boxes and axles to even a warped rotor causing this. Where to start?
View 4 Replies
My wife has a 2003 Camry that we had to replace the clutch last year. Now her clutch pedal goes to the floor and does not return.
View 2 Replies
I have a 2002 Celica GTS with 80,000 miles. The clutch pedal pressure was very stiff. I had a 2001 GT, and it had a very soft and easy clutch. I just removed and rebuilt the clutch slave cylinder, using the CSK 2426 rebuild kit. The slave cylinders on 2000 to 2005 Celicas are all the same. After bleeding the cylinder, the pedal pressure is very much improved. It still takes some effort, but not like before.
View 1 Replies
Facts: 1999 Vw passat 1.8t
1 year ago, clutch pedal would not come up off the floor, no life in the pedal.
Problem: Clutch master cylinder, replaced.
6 months ago, clutch finally went bad. Took car to clutch shop, replaced clutch kit(found out after i payed that they only turned the dual-mass flywheel... ). Get car from clutch shop, the clutch pedal came up only 2-3 inches off the floor by itself but you could lift the pedal with your hand or foot, and it would come back up all the way, but it was life-less. It was not pulling fluid in. It was catching extremely low. I called the shop, they said that it was just because it was a new clutch and it would get better. I didn't believe them.
Two days ago, I got into my car and couldn't get it into gear. Clutch pedal would go down with the same amount of force as before. Took it back to the clutch shop and explained the history with the clutch master and then them doing the clutch kit. They said it wasn't bleeding properly and they're not sure if its going to have problems again. Car is working now, but I am concerned that it will have similar problems again.
The tech who fixed it said he pumped fluid into it extremely hard, and that's what made the pedal come up all the way (no longer stops 2 inches off the floor) and its going into gear just fine now. What the problem might have been? Block in the hydraulic lines? If this is the case, does forcing fluid through it fix it?
View 2 Replies
I just replaced my clutch and have put everything back together, and bled my clutch line, but I have absolutely no pressure still in my pedal. I read that u need to make sure your brake fluid reservoir is filled to the max, but following the clutch line, I dont see it going to the reservoir? I also read that the master cylinder is behind the clutch pedal, does the master cylinder hold any fluid that maybe I lost during the bleeding? I'm at a loss right now.
View 12 Replies
I'm a single mom and really dependent on my car for my job and my kids... I have a 1995 Chevy Camaro 6-cylinder, and I am having engine problems... in the mornings, my car starts fine, but if I drive more than a few minutes and turn it off, she doesn't want to start up again. It turns over just fine, but it sputters and refuses to stay started. After a couple of tries, I can get it going, I rev the engine, and a cloud of dark smoke (not blue and smells like gasoline) comes out. I also smell gas strongly when the engine idles after everything smooths out. Sparkplugs, fuel filter, oil, air filter, belts, hoses, all have been replaced recently, catalytic converter is only four years old, and car has 178,000 miles on it. What I may be dealing with? I'm also losing acceleration/power when I try to speed up...
View 14 Replies
So last night I was driving home from work, and at a red light while i was waiting to go i had my clutch down when light turned green i tried to go and noticed i could not put it in gear and that my clutch pedal was stuck in place. i didn't know what to do so I checked my shifter plate everything looked fine so went to look at the pedal and i pulled it forward and it came lose. I started it up everything was fine and back to order. This morning going to work same thing happened again, I don't know what is going on and what could be the cause?
View 5 Replies
I'll drive my 2000 Ford Ranger, 4cyl XLT about 5 miles to the store without a problem. On the way home, after a few miles, the clutch pedal will either jam at the top, or go all the way to the floor without engaging the clutch. If I wait 5 or 10 minutes, the clutch pedal will start working again for a short time.
If I feel the clutch pedal starting to misbehave, if I ride the clutch and don't release the clutch pedal all the way, and if I don't push the clutch pedal all the way down, I can keep driving the truck. As soon as I release the clutch pedal, it will jam up again, or the clutch pedal will go all the way to the floor without engaging the clutch. I don't like riding the clutch, but that seems to be the only way to get home once the clutch pedal starts jamming.
It certainly seems related to the engine warming, or heating up. Sometimes, after the clutch jams up, I'll wait 5-10 minutes and the clutch pedal will start working as if nothing every happened. So, it can't be strictly a hot engine, hot clutch fluid issue, right?
What would you attempt to replace first, the Slave Cylinder? The Master? Changing the fluid? Shooting the truck!?
View 8 Replies
I've been driving manual 12 years, all my driving life, and been in 10+ manual vehicles during that time, including a 10+ year stint in a 1.8T Passat with a 5-speed.
In all that time, and all those experiences, I've never replaced a clutch, damaged a clutch, or had one problem. In fact, I consider myself a very good operator of the manual transmission.
This is preface to my current situation. 2009 Tiguan (early build) 2.0T 6M, driving at 57mph in 6th gear - downshift to 4th to pass a truck and WHAM. Grinding, confusion, and then the clutch pedal stuck straight to the floor. Glide to a stop on the side of the bayou road.
Totally immobile vehicle. Impossible to shift into gear, or get the pedal off the floor except by pulling. Smell of acrid smoke.
VW dealership says "we're doing a courtesy warranty repair" on the clutch, flywheel and bearings, as if it's my fault. Impossible. This is a mechanical defect if I ever saw one.
View 9 Replies
Started losing pressure on my clutch pedal yesterday. When I would push in the clutch pedal it would not push back up to the reset position. It would only come back up half the way. Now today I have a steady ABS light and ASR light on. Checked for fault codes and found no trouble code. Checked brake fluid resevoir for leaks; still has plenty of fluid. Checked slave cylinder bleeder valve for leaks and looks dry. The only thing I think it could be is the clutch master cylinder. If I drive the car for a few minutes I am able to build pressure back up in the clutch, however the ABS light and ASR light still remain while driving. Turning the car off and back on again shuts off the light for a few minutes until I start driving, but the clutch pressure starts back low again.
View 3 Replies
I was leaving a training class today and the cover on my gas pedal got stuck, I came close to a truck. (new car + big truck = not good) i stomped on the gas a couple of time and got it to release. I was not in a high traffic area.
View 24 Replies
Car: 2012 Mk6 Golf R
Mileage: 43,000 km
Software: UM stage 2 loaded
Related mods:
- diesel geek short shifter
- Emmanuel design, Sachs SRE stage 2 SMf clutch kit
- Tyrol sport deadest rigid collar kit (probably not related)
Background info:
Clutch installed at 40k km.
0-500km stop and go traffic
500-505km punched it bc a 350Z pissed me off*
506-1200km highway and not very aggressive twisters
1200-3000km hwy and city mix
First 0-500km I babied the clutch. No issue
501-505km I punched it a bit hard. Felt great. No issue
506-1200km hwy there, no issue. Closer to the 1200km mark the issue surfaced
1200-3000km was able to repeat the issue and adjusted diesel geek ss and re-bled the clutch in attempt to resolve it
Issue:
- from dead stop, 1st gear gets locked in at 2-4k rpm
- either I rev up beyond 4k, drop below 2k rpm to unlock it
- if I man handle n yank it out of 1st, gears grind
- only happens when the car is fully warmed up and fully running at optimal temperature for at least 10-15 minutes
- diesel geek ss readjustment
- re-bled the clutch (no topping off the clutch lines)
Issue was improved, however, I'm experiencing this locking issue again. Less frequent and less predictable. Attempted to replicate the issue, only happens if it's stop and go traffic-jam speed. Was unable to focus on an rpm range.
View 5 Replies
