Golf/GTI VI :: Check Engine Light Has Been On - Car Sputter And Misfire
Sep 15, 2012
So, my check engine light has been on for months. I knew that I needed a new oxygen sensor (block 1-pre-cat), so I replaced it today after the car began to sputter and misfire. Well, I thought that would fix the problem, but it hasn't. Some of the hesitation is gone, but the sputtering is still very bad. I'm going to replace the spark plugs tomorrow and see if that works. I was also told to clean out the catalytic converter, but I don't know how to take it off. It wouldn't hurt to just bang out all the debris. Any DIY on taking off a catalytic converter for a 2000 VW Golf GTI 1.8T?
View 7 Replies
Advertisement
2000 GTI GLS 2.0L ... I understand I need to replace the Ignition Coil Pack on my car. I have looked on ECS Tuning to find the coil pack, but from all the pictures I see of other people coil packs they look nothing like what mine do. So I'm wondering if they are different for my specific car? So the issue that I have is my engine sputters sometimes, but more so when is wet outside. Its only cylinder 2 misfiring currently, and I replaced my Fuel Filter and Fuel Pump already in the past 4 or 5 months. Also a local shop had done some work recently and I know they had replaced the spark plugs. So I'm just wondering what coil packs I need for my car, and how I would go about replacing them. From what I saw online with other 2.0L (They weren't GTIs tho) was that the coild pack was behind the SIA pump or something like that, and they are a small black box. It looks to me that my coil packs are inline above the spark plugs and cylinders?
View 2 Replies
I changed my plugs a few days ago on my 96' Taurus GL 3.0LI checked under my hood to check the recommended gap size and it said .42 to .46.. I went with .46. after putting them in i started the car up just fine, but later in the day i noticed when I came to a stop at a red light my car would sputter and my check engine light would start blinking. When I'd accelerate and drive it again everything would clear up and the light would stop blinking. I didn't change the wires, just the plugs in case you were wondering but I am unsure of how much that would influence my problem. Today after work i had a little trouble starting my car. After a few tries it started and my exhaust smelt rich in gasoline. Did i gap them too much? Should i get new plugs again and regap them? should i buy new wires also?Is my ignition coil going bad?
View 19 Replies
On my way to work, my check engine light started blinking and car was sputtering (real bad on idle). I ran the code and it came back with misfires codes. I changed the coils/plugs, fuel filter and fuel pump last year. Can the coils be bad already? When I clear the codes the car will run fine for a little while. But after a couple miles CEL will blink and the car will run roughly again.
Car : 2004 Golf 2.0
Codes:
16684: random multiple misfires
16648: fuel injector #2 short to ground
View 5 Replies
My 2002 Jetta GLS 2.0 is misfiring only when it rains out. I go to start the car and the car idles extremely rough and seems like it wants to die. I checked out the codes for the check engine light and I got misfire codes p0304 and p0300. Which is a general misfire detected, and misfire on cylinder 4. I noticed that when I misted the alternator during the day around 70 degrees with the car running the car would misfire and almost die out. I know you are not supposed to get the alternator wet, but keep in mind i did not soak it I misted water on it. I misted the coil pack and nothing happened. I replaced the spark plugs and wires a few days ago. But as soon as it rains my car does not idle right and the check engine light flashes.
View 4 Replies
My car will drive fine, then @ 60 mph or above sometimes it will sputter and the check engine light will blink on. I brought it to my mechanic and plugged it in. Miss-fire on some spark plugs. They replaced all spark plugs and wires. The car is sill doing the same thing. My mechanic plugged it in again and now just a miss fire on #2 plug. (even after new wires and plug) Only seems to happen once the car is warmed up. If left sitting for 15 hrs the check engine light goes off completely. Only to come on again, after driven 25 or more miles. What could be wrong?
View 10 Replies
So last Thursday I started my car up in the blistering cold and it ran fine for about a minute and started to misfire so I shut it off. It hasn't ran since. When that happened the check engine light was blinking because of the misfire. I didn't have a code reader at the time to read it. now that I got a code reader the damn thing isn't throwing any codes. it spits and sputters sometimes. I've had no previous problems with the car. Thinking It might be a weak fuel pump or bad coils and in not sure how to test them.
View 1 Replies
What are the common misfire problems with the mk4 R32? My R is acting funny every once in a while it runs perfect then some other times it seems to big and the check engine light starts to blink but doesn't stay on I ran for codes and it said I had a miss fire but after that the code never came up again but it still blinks.
View 7 Replies
I drive a 1992 Mazda Protege. Recently had an oil change and put in new air filter. Recently the check engine light has been coming on. Sometimes it will run rough and sputter a bit when the light flips on and then runs normal after the light flips off, sometimes it seems to run fine when the light comes on, but the light does go off and the car runs fine after it has been running for a few minutes. Shortly before I had my air filter and oil changed I did have an incident at a stop light where the car died and did not restart for a full five minutes, at which point it sputtered for a bit and then got me home.
I took into the local mazda service center and dealer (they were the only ones who had the right kind of connector to pull the error of a car this old), and they said the only code coming up was a p69 which indicated a bad thermoswitch. I have already paid for it but the parts won't be in until Saturday. I have until then to cancel the repair and just pay restock and the original diagnostic fees. Should I go through with this repair, or do the symptoms described indicate something else?
View 2 Replies
My 2002 Windstar SEL has been giving me a fit and I`m not getting any codes as to why. Here`s the 2 main issues. Clicking when i go to start up in a.m. if it`s below 50 degrees. ( Battery has been checked and all is o.k. or so I was informed). As long as it`s warm it starts fine every time. Also,it seems like the least bit of wet on the underside will cause it to spit and sputter and the check engine light will start blinking until it sits and dries for a while. (A very shallow puddle less than 6 inches deep at low speed or even the automatic car wash that sprays the undercarriage).
View 2 Replies
My car sits with 45,000 kms on the clock. Had it stock for the first 5k kms and then went stage 1 w/dp and intake. Have been beating the ever living piss out of this car since, and more so since stage 2 got revised again. At about 30k kms I started to develop a random sputter/misfire that was only really noticeable at idle, more so with a mount insert installed. Approaching my winter tire changeover and oil change I had planned to do this past weekend I ordered some maintenance stuff from ECS (filters, spark plugs, spare coil just in case). I had recently got a CEL with a "cylinder 2 misfire" code. I cleared it and it came back within a couple of days, again cylinder 2. Great, nice and easy..Sorta.
Picked up my parcel from the WA post office and installed the coil right there to see if it would go away. And...... NOT. Not worried at this point as I figured the plugs were just toast from so much hard driving for the past 40k kms. Got her into the shop last night and did my tire changeover, oil change, put the factory coil back in and changed the plugs. Here is what I found hiding in cylinder #2,
The car runs so smooth. It's like I found another 10hp lol. Definitely recommend changing up the plugs if tuned and putting kms or miles on the car. With the added power I'm guessing the life span drops off quickly.
View 7 Replies
I have a 2002 Mazda Tribute V6 with 151K. My check engine light has come off and on for quite a while now, mostly it would come on when it rained and then go off when the weather cleared. When it was on, the engine would sputter or misfire. I first had Auto Zone hook it up and they said it needed its plugs and wires changed. No problem. I took it in to a repair place and was informed that I don't have plugs and wires, but something with coils and that since it was impossible to determine which coil was bad, all would have to be replaced at a cost of $1500. I then took it to another repair place and they said the same thing. Now I have seen some discussions regarding this same thing and apparently some people have been able to identify a specific coil. At this point my check engine light is now on all the time and I'm really worried about doing terrible damage.
View 19 Replies
The problem that causes the check engine light to come on cannot be traced. The diagnosis is multi engine misfire. The dealer has checked and recheckedbut problem still exists. The last time my mechanic changed spark plugs he noticed oil on one of the plugs he removed in the rear side of the engine. He replaced the plug with the rest of them. Could it be that one or more of the spark plugs are sucking oil and causes the misfire? If so what could be the cause of that. Do I need a full tuneup? My dealer recommends replacing the cam shaft pulley because it's loose and this may or may not solve the problem. I'm not a mechanic but it appears as if the problem has something to do with the spark plugs sucking oil since the check engine light might go ou for a week or so and then come back on for a while. Lastly is it dangerous to keep driving the car especially on long trips?
View 1 Replies
I'll try to break this down as best I can. I went to my mechanic this am with a check engine light. My suspicion is 02 sensors. This was confirmed as a problem area, but separate they said I had a spuratic misfire in cylinder 4. With that info, i pulled the plug to inspect (I had just installed new ngks in it and they have 18,000K on em.
I put beldon wires on about 8k ago.) plug looked to be normal, but there was definitely a puddle of oil from the valve cover leaking. Oil went into the cylinder head but I didn't really think that was an issue. Nothing abnormal jumped out at me so I reinstalled plug and checked all wire connections at both ends and called it a day.
Then I drove it. Check engine light flashing. Major performance stutters, etc. I drove it for about 20 miles and hoped it was just the oil raising hell in there and it would burn off eventually. It hasn't gone away yet. Maybe coil pack. Can the single portions of that pack be replaced, all i see them sell is the full three as a unit.
View 7 Replies
I just received a check engine light and the diagnostics from dealer were that a misfire was detected for cylinder 1 , 2 , 3 and 6 .
What needs to be changed? and mechanic said maybe the complete coil pack and wiring . Although, the code was reset and i haven't had the CEL come on prob in a week now , so i guess no other misfire has happened.
View 19 Replies
2000 Chevy S10 pickup
Had the check engine light come on, and when I checked on the code it gave a 4th cylinder misfire. Autozone instructed me to simply replace my spark plug with a new oem plug.
I replaced the spark plug as instructed. After about an hour of driving, the check engine light goes off and I think, great! Problem solved. However, another hour of driving and the check engine light is back on again, without going away.
I headed back to autozone to get a readout, just to find that it's the same code. So I put another spark plug in. Same result - check engine light goes off after an hour, only to come back on again permanently after another hour.
Now, normally I would think, this must be the spark plug line that needs replacement,however I am sure there must be some clue in the fact that the check engine light turned off for an hour.
By the way, not sure if relevant, but I also found a lot of build up around the spark plug before I initially changed it.In fact, there was so much that I had to scrape around the plug with an awl, and blow out the crud with a compressor,just to get my socket into place without there being crud in the way.
Any clue what that check engine off/on clue might be?
View 6 Replies
Got the flashing check engine light and loss of power for few seconds and then the light stayed still, from time to time it blinks for few secs, usually when I push the gas pedal little bit more but it stays still, flashed only twice in 2 days for seconds. I connected computer (not VAG) and it says "Cylinder 4 misfire". I have app scheduled with my mechanic this Thursday, but still need to commute to work. Is it safe to drive?
View 7 Replies
I have a 2001 corolla with 37K mi on it. The check engine light came on today. Took it to advance auto parts to read the code. It showed P0171 (System too Lean) and P0300 (Random Misfire). Called up a toyota dealer and the technician think it might be bad gas. I buy gas at name brand gas stations and sometimes from BJs. I am not sure if the problem is with gas. I also been up to date with maintenance.
View 14 Replies
I plugged in a OBD2 reader and its show misfire on Cylinder 1.
I haven't driven the car for 4 days, and when i started the engine this morning, the engine show knocking when the regular engine kicks in (rough). i will be bringing the car in tomorrow (dealer). my car is a 2011 with 16k miles, strange for this to happen so early in age.
View 2 Replies
As the title says I have plugged a code reader in and it says "cyclinder three misfire". So I pulled the plugs and good god they were nasty. Some having a gap of 80-90 thousandths of an inch. So I figured the plugs were the source of the problem, thus I replaced them but to my dimise the check engine light is still on, and still reading the same ol' "cyclinder three misfire". I have put 350 miles on it in 24 hours of changing it to allow for proper time of the circuit cycling for the light to change but not sure if it takes longer...?
I also went ahead and checked the plug wires resistance when I had the plugs pulled and they ranged from 1.5-2.5k ohms shortest to longest (cylinder 4-1). And if your curious the magic cylinder three was around 2k ohms for however long that wire is, my guess would be 18 inches. Would this be out of tolerance, I know the norm is 10k ohm for every 12 inches or so...?
My next guess would be replacing the power pack or I guess you car guys call it the "ignition coil"...? I will say that the car does run much smoother after replacing the plugs.
View 5 Replies
Honda Odyssey 2005 – 176000 miles. Cylinder 4th Misfire – check engine lightHonda has about 176000 miles. When cold – before warming up – it acts like nothing is wrong – as it gets warmer – to the middle of the temperature gauge – it misfires.And runs rough. Evaluation: Honda Dealership thinks it is a cracked Valve or needs adjustment – they have replaced a spark plug and swapped coils. Not for sure.They think if that is not the case then there could be additional problems.Question: Why does it act normal when cold ? How can we confirm if it is the valve and not cracked head?
View 15 Replies