So, this morning I stopped at the grocery store and when I came back out I started my car. The car ran for about 20 seconds then stalled. Luckily I was able to get the car to the other end of the parking lot for a tow truck yes, this meant starting it about 6 times! This is the second problem in 12 years of owning vw's I'd say that's a good track record! I did a complete auto scan.
View 20 RepliesI am working on my father's boss' 2004 Phaeton V8. The car usually sits on the weekends. What it is doing is, it will start and run smooth, but after 15 seconds, on the dot, it stalls and dies. It sounds like it is starving for fuel.
What I have done so far:
LH intake actuator arm found broken, replaced both with "Gruvenparts"
Checked all fuses and relays
LH fuel pump reads 14 volts until the relay kicks it off
Tested fuel pressure-good
Batteries fully charged
LH fuel pump reads 0.7 ohms w/key off
RH fuel pump reads 6.0 M-ohms when first connected and gradually climbs to 31.5 M-ohms
(I assumed this meant RH pump was bad and so I pulled it out and bench-tested. Ran perfect and tested at 0.7 ohms out of the car)
Re-assembled everything to pull the car out of the shop, and wouldn't you know it started and ran like normal.
Road-tested for 2 hours the next day without any problems.
So, I call the customer to pick it up and he says he will be there 2 days later.
I've been having some issues with my mk4 R32. Right now i'm leaning toward changing the fuel pump and filter but i want to be sure before i do.....
Problem: I've been daily driving my r32 to work for the past couple weeks and about once a week it will start, idle for a couple seconds and then just bog out and die. no codes, just idle, then chugging and dying. it will fire with some starter fluid and will sometimes hold a very sickly idle but most the time will just run the starter fluid out. the weird thing is is that it's intermittent and will happen randomly and if i leave it overnight or sitting for a couple hours it will fire up like nothing was wrong. i just wanted some input on what it might be before i replace the pump. i have already done the relay so its not that.... the only code that it has ever thrown while i have owned it was for the intake changeover valve (N156) which i cleared and it hasnt yet to come up again.....
I have an 04 w12 with 80k miles on it. It will start fine but will not run for more than 10 seconds. As it idles down from startup it settles to about 700 RPM's where it normally does then dies. If u drive it it will start and go into gear fine as u go to pull away it loses all power and dies. I have checked the minor things i know like air filters, oil, tranny juice all appears normal. New batteries less than 3 months ago also.
View 11 RepliesI'm having a bit of trouble with my fathers '03 Ranger Edge 4.0L. It has about 100k miles on it, and we keep it very well maintained. This is the first major problem we've had with it.
When the problem first occured, it had been driven about 30 miles on the highway and about 5 miles after getting off the highway, he pulled up to an intersection and stopped. As he started accelerating again, it all of a sudden started sputtering, surging (almost exactly as if it were running out of gas), and then stalled. It continues to exhibit this behavior. It will start and idle fine, but struggle and then stall when given any amount of throttle. It's also an automatic transmission if that makes any difference.
Fast forward to this past week after we had it towed home. We have checked the fuel pressure, and its dead on at about 64psi. We changed the fuel filter, changed the PCV valve, changed the upstream O2 sensor, put in a new air filter, cleaned the MAF sensor, and cleaned the intake of the throttle body. We're now at a loss as to what could be causing the problem. The CEL is not on, and there are no codes being shown when we plugged it in. We also thought it may have been bad gas, so we drained the tank and put fresh gas in from our preferred station. The plugs and wires are also fairly new, only about 4k miles on them.
Are we missing anything here? What else we could try? The absolute last resort is taking it to a shop, we're going through a rough patch with finances.
2010 Escape with 74,000 miles. Backstory: This is my daughters car who is away at college about 300 miles away. About a year ago the engine started hesitating when driving and would stall to idle at highway speeds. She took the car in to dealer and they replaced the Throttle body under the CSP that had been issued just prior to the dealer visit. All was fine for about 3 months, then she reports that the car is doing the same thing. Check engine light briefly illuminates and goes right back off when this occurs. She is able to slip the car into neutral and it seems to correct the malfunction. Unfortunately she has gotten so good at this that she keeps her hand on the gearshift when driving. It seems to happen at various speeds with no warning and no lasting effects.
She came to visit for Christmas and I was able to replicate the problem after about 30 minutes of city driving, but not quick enough to take a picture of the wrench that illuminated briefly. I slowed to the edge of the road, put it in park and turned off the key (engine ran the whole time at idle). Cranked back up and good to go! She had the oil changed about a thousand miles ago, I replaced the air filter last night and she had to return to her house for work in the next couple of days. She said it happened 5 times on the way home last night.
Car has always been serviced regularly and was a certified pre-owned when we bought it in March or so of 2012. I also bought the extended warranty although that may be expired by now.
Her local dealer said they can't fix it if the CEL is not on or the problem is not occurring at the exact time they have it in the shop. Now, I am not sure but was under the impression that the computer would record any codes and store them even if the light went off and the car returned to normal.
My 2006, 4.2 has been really erratically not starting. Turns over fine but will sometimes fire up and tries to run on maybe 2 cylinders, then stalls. Now it won't even do that, nothing. No check engine light or codes. Guess what the thing started up this morning 7 degrees out and running like a charm. Turned off and nothing again. Replaced relay for PCM ,no change, still no codes.
View 9 RepliesWhen I start my car it seems like some of the cylinders are missing for like 5 seconds then runs fine. Sometimes its quite violent and this morning it stalled the first time I tried. The colder it is outside the worse this becomes.
The car is still under warranty, but you have to wait a week to get the car into the dealer here and a battery wouldn't be covered anyway. Here is what I have so far.
Bad battery : The car has 45k miles on it and as far as I know the battery is stock. Also, when I did the 40k service I seem to remember something about the battery on the invoice (I will look), but I was too busy worrying about the bald tires. I do generally leave my ipod plugged into my car stereo (which charges it) over night, so that is putting a drain on it. I am going to take it out of the car tonight and see if that makes a difference. I suppose I could take the battery to O'Reilly's and have them test it, but it seems like it would be in their best interest to lie.
Coolant temperature sensor : The car was recently in the shop and they said they found a small coolant leak and fixed it, maybe the sensor became damaged? Most reports I see about this suggest the car runs rough for much longer than mine and must be fed gas.
I start the car - a 2001 Ford Focus 4 cyl DOHC. It runs fine for 30 seconds then stops, as if it is no longer getting fuel. I can't start it again for a couple days then the same thing happens over again. FWIW, I parked the car for 8 months before this happened and only started it once in that time. But it ran fine then and before I parked it. What can this be?
View 1 RepliesToday I acquired a 1982 F150 with a 302 engine, 4 brl. Edelbrock carb. The truck starts and idles just fine, but when I come to a stop, try to give it gas to go it dies. It starts right back up, and I have to rev it high a couple of times then put it in gear and it will finally go. When I got it home I let it idle a few minutes and tried playing with the air and fuel mix but don't know what I'm doing, really. It seems I can hear a hiss, and when I was reaching for the air/fuel screws I got a little shock on the hand from the distributor. We want to use this truck as a farm truck, and plan to get a manual for it, but what might I might check for the cause of it stalling.
View 1 Replies1992 Mercedes 300E with 160,000 miles that I've owned for 15 years. Car runs fine for approximately 10-20 minutes and then starts to sputter and cough and if I don't increase the RPM's it will stall. If I increase the RPM's it will smooth out for a little while, but after a couple of minutes with higher RPM's it will sputter again and finally stall. After it sits for awhile I can start it up again and it runs fine for another 10-20 minutes. No check engine light is on and the car is OBD 1.
This problem preceded the weather recently turning cold. Thus far I replaced the spark plug wires as the other ones were old, but this didn't work. The spark plugs themselves were replaced about 2 years ago. At this point I'm suspecting it needs a new distributor cap and rotor (when I replaced the wires some of the cap's posts had corrosion, which I cleaned off with a brush).
1995 Mazda Protege1.5 LAuto153K miles.
My car was running fine, then one day it started sputtering while driving, mostly when I accelerated. It stalled and I could not get it started. This happened on a day when it was raining hard, but not sure that had anything to do with it. A few days later when I went to pick the car up it started right up, it had stopped raining and been dry for 2 days prior. But about a mile into the drive back home it stalled and I could not get it started.
Here is what I have tested so far.
- Put in new fuel filter.
- Tested the fuel pressure and pressure regulator
- Tested the injectors with a noid light.
- Tested that the spark plugs were producing a spark.
After I pulled the plugs and cleaned and dried them (they were wet with gas) the car started, but I think not because of anything really related to the plugs. What I've noticed is that when cranking the engine if I give it gas it will not start but if I keep off the throttle it will reluctantly start. But once it starts the idle is smooth and as it should be. Then if I give it any gas it immediately stalls. It seems to me given these symptoms that it is getting enough air to idle but not enough air to match the increased gas.
The only CEL code that I'm getting (which I had before this issue occurred) is the "closed throttle position switch" (I forget the number). If it was an MAF, or IAC, or EGR issue would I not get a code? What this could be and how to test it. Again my guess is its an air intake issue but not sure where.
A few days ago, I went to start the car, and it will start, and idle fine for a few seconds, and then begin to run crappy, idle down, and die. I tried starting it, and giving it some accelerator pedal, and it dies. I changed the timing belt, idler pulley, and tensioner this summer, so I'm ruling out a bad timing belt. There is no check engine light, and I replaced the plug wires because when I removed the cover, I noticed one of them was worn in a spot, and the wire shielding inside the rubber insulation was visible.
View 11 RepliesHaving some problems with my 92 Nissan NX2000. i just finished changing the clutch on the car now its acting horrible.
When i start the car, it will run decent for like 2 or 3 seconds then the idle drops down till it almost dies, catches itself, idle goes up to about 500 were it will pulse around for a few seconds until it dies. If i rev it it will stay running, kept it running for about 2 mins. but as soon as i let off it will pulse at 500 until it dies
After i changed the clutch it started up fine, it ran great for about 20 seconds before it just died. when i started it after is when the problem arose.
I took a video of the car running, which can be seen here. [URL] .... (It has never caught itself like that before and jumped up to 1000 rpms before. It normally will die at that point)
The video is really quiet, not sure what happened there. if need be i can get a video of the engine bay so its louder, was mainly focused on the RPMs.
Here's a few things i tried: Checked fuses, Changed spark plug wires, made sure they were all seated good, MAF wires were rubbed a bit so i cut the MAF pigtail off one of my other sentras and soldered it on,Changed to a good battery, Changed fuel filter, Added more gas (in cause gauge is broken), Made sure all connectors are plugged in, Checked around for vacuum leaks, found that one of the large hoses coming off the intake going to the engine had separated so i plugged them back in and nothing.
Bluetooth audio malfunction. When I start to play a song, it plays fine for about 15 seconds, and then goes silent and seems to fast-forward to the end of the song, and then does the same thing with each subsequent song on the list.
View 2 Replies2000 f350 CCLB SRW 176,000. I have a touchy accelerator. About two weeks ago the CEL came on and it wouldn't do anything but idle for about 20-30 sec then fine. Then it got a little worse. I disconnected the two harnesses on the accelerator pedal and sprayed them with electrical cleaner. Put it back together and it seemed to be ok. Today the pedal is real sensitive. Sometimes bogging down other times accelerating real high even tho my foot is pretty consistent and gradually accelerating. No CEL tho. Do you think I am in for a new pedal assembly? Could it be something else? UVCH?
View 13 RepliesI'm having an issue with the truck not staying idle after cold start up. The truck will turn over and start right away (not even 2 second crank) but immediately dies. The throttle will not work at low RPM. When I start the truck, it will instantly rev high, the revs will drop low, it will try to compensate and rev high again, then it will immediately die.
If the RPMs are under under 2.5k, the truck will immediately stall and die. When I attempt to use the throttle under that RPM, it will not work. No matter how much I depress it, the engine will instantly cut and stall out. It will not attempt to deliver fuel. The only way I can get the truck started is if I rev the engine high and hold it. I need to hold the truck at 2.5k+ RPM for atleast 30 seconds. It generally takes me about 5 tries to finally get it running (mainly due to the throttle immediately cutting out and I have to 'catch' and hold it.) After that, there is no sign or issue. The truck will start immediately back up after it's been running for a couple minutes.
CEL: MAP sensor (0069?) -- Sensor is spotless. Harness looks fine. I replaced the injectors, both batteries, and the alternator this summer. It doesn't sound to be any these either as the truck sounds extremely healthy and immediately turns over.
B1602 PATS Recieved Invalid FMT/Key CD
P0753 Shift Solenoid A Electrical
P0758 Shift Solenoid B Electrical
P0740 Torque Converter Clutch Fault
P1760 Pressure Control Solenoid A Short
p0305 Cylinder 5 misfire Detected
P0316 Engine misfire Detected on Startup
The Trans will unlock while driving for a few seconds then lock back up and drive fine, it seems to be worse over the past couple days. It is no different cold or hot. I also noticed the head lights dim and the voltage on my scanner drops to around 12 volts when the trans disengages. When it is not acting up it drives and shifts perfect.
I have checked a few grounds that were visible and cleaned battery connections. The misfire code has been fixed, not related.
I have Warn hubs that I have to lock in. All works good. A/C goes to defrost at first when cranking but then runs fine after a couple seconds. So, I was thinking that maybe my pump is running all the time. Who knows. I'm sure all my vacuum lines are dry rotted. What exactly is the need for it exactly and what's the best way to cap? Hoping to do it at the unit itself if possible.
View 6 RepliesLet me start with I have a 2003 f250 5.4. The motor blew on my truck and I had a 100k motor dropped in it. I've put new spark plugs, ohmd out the coils. I tried both sets of injectors. cat delete and new fuel pump. It has rough idle and stalls but runs fine at higher rpms. Also has basically no brakes. I am thinking vacuum but I've check all the lines. No codes either!! also cleaned throttle body.
View 4 RepliesCar has 6600 miles on it and is back in the shop for 2nd time to determine what is wrong. Basically, the car starts and then stalls out after a few seconds. It will not start again (at least with me). Course, the dealer can get it started after the tow to them.It began in April after an oil change at the dealer. A week after the change, it started up and then a message SHUT DOWN appeared on the dash.
The car stalled and would not restart. When it was towed to the dealer, it had no oil. Per the dealer, there was no leak and it was assumed the tech forgot to put oil in it, They indicated it was not a problem since there was some oil remaining but the car would still not start. They kept it a few days and replaced the relay for the fuel modulator, electronic fuel pump, fuel unit, fuel pump control unit, e-control unit and of course the battery. Note: this was a cold start.
About a month later, I had driven the car for about 30 minutes, left it for an hour and came back to the car.....it stalled again right after start up and would not restart. After being on hold with roadside assistance for awhile, I tried it again and it started without issue. .
A week later (today), used it for a half hour, came back to use it 3 hours later and same story. Started, then stalled, no restart. Towed it to the dealer and the tech got it started but no codes telling him what is wrong.