I got black side markers for my car and put on the bulbs the side markers came with... I like the look but I got the bulb out error.. Wanna keep these bulbs but the error code annoys me .. Need to know the vag-com code to get rid of this? I searched but I can't find it.. I have a 2012 GTI .
View 11 RepliesI had HID's installed in my fogs (before haters jump in, it doesn't look remotely bad, and they're aimed down, so no glare), and I'm getting a bulb out error. I have a VAG, but I'm not seeing any long coding to disable error checking for the fogs. I have the error cancelling add on, but we forgot to install. Just curious if there's a VAG trick to disable that error before I rip the fogs out again.
View 1 RepliesI have been getting random bulb out errors, usually its the front side lights and today with out turning on the lights I had rear parking light...thing is I get out of the car to check and they are lit? Faulty bulbs? stock tails and side markers but do have a bi xenon retro in the headlights using the usp hid kit in the projectors.
View 3 RepliesI installed the lights and they work fine but everytime I turn them on they throw a bulb out error message. I have the cold diagnosis turned off for the fogs and I still have it. Whats next?
Here is my coding. F78F8F2700041500470F0000000000000018110B5C00010000 0000000000
I have an intermittent error that comes on most of the time I have my headlights on, but sometimes goes off and comes back while I am driving. It shows me the bulb out light, and says on the screen "Number plate Check license plate lighting!" I have never touched the oem factory bulbs on the license plates, and if i get out and look at the plate, both lights are on over the plate.
The only change I have made was about a year ago, I installed an LED bulb in the trunk, and ran a second OEM trunk light in the left side and installed an LED bulb in that too, tee'd off the factory trunk light housing. But like I said, that was 1 year and 30,000 miles ago, and my bulb our error for the license plate has only just started, so I doubt they are related.
I have a 2012 Golf tdi. Got a cel after a 300 mile highway trip.
Got it scanned by dealer, came out to be p2413. Some EGR malfunction. According to service ticket, all vw did was reset my ECM. Does that sound accurate? Car has 16k miles.
Service rep mentioned that it could have something to do with my carbonio intake. True? Or BS?
So far, 100 miles later, no cel and car seems to be running fine.
Just curious if it actually could have something to do with the carbonio, or if he was just busting my balls.
My driver side bi-xenon bulb was out, so I go to replace the bulb and it still doesn't turn on. I scanned my car with my vagcom, and I get this error.
Address 09: Cent. Elect. Labels: 3C0-937-049-30-H.lbl
Part No SW: 3C8 937 049 E HW: 3C8 937 049 E
Component: Bordnetz-SG H54 2602
Revision: 00H54000 Serial number: 00000008706034
Coding: E78C8FA300041C004719000014000000002AF7475C40012539 0000000000
[Code] .....
Unfortunately my HID bulb wasn't secure in the headlight assembly and melted the part that holds the bulb in place in the headlight assembly.
My question is if that part that retains the bulb is replaceable or I will need to replace the whole head light assembly? ( The wire connector is fine.)
If the part is replaceable, What is the name or part #...
I have doing some modifications to my 14' Camry that include the following:
I saw on a Honda Civic one day a very deep blue bulb on his factory DRL's. I am assuming it's shared with his high beams? I loved the color and I'm not worried about sacrificing the high beam for this bulb. Looking for deep blue bulbs that are plug and play for my Camry? This is primarily for aesthetics.
Thinking about getting a used Camry. Is there any issues with any of the years in the seventh generation Camry? What are some of your likes and dislikes of your car? For example I have been told that on the sixth generation Camry you have to remove the bumper to change the turn signal bulb. I have never had to deal with this, just what I have been told.
View 14 RepliesIs there any way to turn off the little green light bulb icon in the instrument panel? I run my dash light at minimum brightness and that little light bugs me.
View 3 RepliesI have a 2012 passat se and the airbag error light came on, after it did all the buttons on the steering wheel and the horn stopped working. How is the best way to fix this?
View 4 RepliesI recently got a 2014 Camry SE and have started to experience problems with the USB port in the center.
I generally plug in my 5th gen iPod to listen to audio, but I've started to get an connection error. The message reads Connection error. Please consult your Owner's Manual for instruction on how to connect the USB device." (see image link below)
Sometimes the iPod will connect, but most times it won't. If it does connect, the error will appear when I hit a big bump or pot hole, leading me to believe there might be a connection or soldering failure somewhere.
I can confirm that it's not the iPod's problem, my cell phone, tablet, or any other device plugged in will not get a power signal either. The iPod will connect via Bluetooth, but that is not optimal as I'd rather have my phone connected for hands-free calling.
If not, how easy is it to open up the console to get at the connection to check/fix it myself?
I have a 2012 F-150 XLT with 5.0L V8. I am constantly getting a PO304 (misfire) error. This is what my mechanic has done to try to correct the problem. 1. replace plugs 2. replace coil 3. replace coil cables 4. replace injector kit.
The question I throw out is: What other part or adjustment is left?
After clearing the error it seems the Check Engine Light will not come one until the next morning. The engine seems to misfire then then I get the Check Engine light again.
I want to change out my fog light bulbs on my MK6 Golf TDI. does this will set off any E-Codes or can I just plug and play?
View 5 Replies I have read all 11 pages of the led light post, and I am more confused then when I started. I bought Ed's opt.4 lights with the LED's. I bought the light kit he recommended: [URL] .... with H7 harness. I have 2012 North American TDI Golf. I purchased and had installed the Bold eruo light switch with light sensor kit. I had someone install everything for me. They have had trouble finding out the proper codes needed. The issues I am having are:
1: with the above set up, they can not get the light bulb out warning light to go out. I was told that it is due to the light kit purchased above, and the fact that it only connects to the drivers side harness, and not the passenger side, so the warning light on my car keeps saying there is a bulb out on the right side.
2: With the euro switch in the Auto position, I get no DRL's at all. The only way I get that is if I turn the switch to the next position, and then I get the low beams, as well as the LED's, and no fogs. This stays the same day or night with the light switch in this position. To get the fogs as well, I turn the knob one more turn, and pull it out, and this gives me the fogs as well as the low beams and LED's.
My questions are:
1: can I get the LED's as DRL's in the Auto position or in the position next to it, and then have the rest of the lights come on automatically at night via the sensor? If so, what are the vagcom codes I would need?
2: Is there anyway to get the bulb out warning light to go away without putting in a different light kit. I was told by the installer that they had to try a few light kits to get one to work with the coding of the vw, and the kit they use connects with two harnesses(one for each head light, and not one harness for both as my set up is).
I recently installed the LED euro tail lights with out swapping pins, or any ghetto harnesses. i simply installed my tail lights with the oem harness. Anyways, after i installed the lights, the bulb out warning came on, i got rid of it, but when i press the brakes it triggers the warning light to appear after i vagcomed it to go away. so what is the coding to get rid of it?
View 2 RepliesOne of my headlights burned out.
I was looking at ECS and saw ES#1059.
Just want to make sure that this is the right bulb.
I've been searching around and have been reading that the easiest way to do it is to remove the front bumper. I'm really hoping this is not the case. I've only taken a quick look at it, but it does seem that some things will need removed. Any quick explanation of the easiest way to get the assembly out of there?
View 4 RepliesI have a 15 Camry, and the other day after about five minutes of driving, the BSM (blind spot monitor) gave a long beep and then an error message to check the BSM showed on the instrument cluster. I tried to reset it while driving by turning the BSM on/off. This didn't work.
After restarting the car, it went away. I've never had a car with BSM, and didn't see any damage to the bumper.
So, I'm not entirely sure if this has been covered, but I dealt with the bulb out warning with the LED tail lights. I am not running the fourth wire. I had tried searching for a while but found no answers. Most conversation about this issue are buried in old threads.
The usual DIY disclaimer applies. In the Central Electrics module (09), access Coding, then Long Coding. You will need to make sure that Byte 19, Bit 3 is checked (Diagnosis Rear Parking Lights Active).
Here is my current coding:
E68D8B6700041500470A0000F000000000918095C000100000 000000000
I have verified all operations (parking lights, brake lights, turn signals [amber]) and no flickering as well.