Golf/GTI VI :: 2011 - Filling / Painting Holes In Front Bumper
Jan 21, 2011
I just bought a 2011 GTI in Steel Gray Metallic. The first thing I did was remove the front license plate holder.
Doing that revealed 3 large holes (about 8mm), and 2 small screw holes. I'd like to repair this myself or have a shop do it.
Is there a relatively easy way to fix this myself (other than putting the holder back on)?
View 8 Replies
Advertisement
replacing the entire front bumper.I have removed the front license plate holder, and would like to fill the holes where it was screwed into the front bumper.
View 8 Replies
What I should use to fill the holes on my front bumper? I know how to get paint to make it blend in but what should I use as a filler?
View 1 Replies
I plan to remove the front license holder from my car, fill the holes, and paint/clear coat/sand them. Any recommendation as to what to fill the holes with (I'm not going to use a plug.) Exactly what the bumper cover is made of, I can find the right material to bond to it.
View 2 Replies
I need to put a front license plate on my Prius. I notice there are a couple little indents on my front bumper but no holes . Do I need to drill holes or something else here to mount a plate ?
View 13 Replies
I bought the car from dealer, there are now FOUR! holes on the front bumper. I don't understand why they couldn't just use the existing holes to put the license plate holder. Now I'm stuck with these holes and I'm looking for a cheap alternative to fill them. I like the clean look of the front end without the plates and don't want to spend a fortune at a body shop, but I also don't want 4 dots either. What I can do/use?
View 3 Replies
How do I get rid of license plate holes on my front bumper? I took my front plate off and now I am stuck with annoying holes drilled into my front bumper. Its not noticeable but i know its there so it irritates me.
View 4 Replies
I'm having the bumper cover replaced on my 350 (stupid mistake on a number of fronts it's starting to look like...) and the indy shop that I chose in my town to do the job (Lexus dealer is 100 miles away and this shop was recommended by the guys that take care of all the Lambos/Ferraris/Porsches etc) told me that they had to drill the holes in the bumper cover to retro fit the sensors. Is this correct?
View 2 Replies
How the black trim on the bottom of the front bumper of a 2011 Elantra GLS is removed . I am talking about the black lip or air dam in the center. Does it just pull off or are there clips or something.
View 1 Replies
I have took off the screws in below pictures. But the bumper seems still stick on the car body. Any screws are missing? Or other issue?
View 4 Replies
I'm having trouble removing the front bumper. Does it remove like the GTI or is it different? I don't have the confidence to pull harder without knowing.
View 2 Replies
I need to remove the front bumper cover of my Mk6 GTI. I think I know how to do it.
View 1 Replies
I just received a new bumper / grille assembly to put on my car, my old one got destroyed pretty much, I was wondering if there was a guide of some kind or a diagram that i can use to put this on? I'm a bit short of time so im looking for anything ASAP.
Any diagrams / Visual guides / tips and tricks of the sort, or even some pointers on putting the whole front end assembly on.
View 6 Replies
I noticed while parked under the sun for a while the front bumper expands, fully exposing the small cut outs or tabs usually hidden under the head lights. I brought it in to get checked out and being told that every clip and screw are in the right place. Later on that day I met with the mechanic, he explained that the bumper is a little different as far as mounting goes compared to other vw's leaving a weak spot.
View 15 Replies
So I am in the process of removing my front silver grill to paint it and was wondering do I need to drop the whole bumper to get it off??
View 16 Replies
What the square piece on the passenger side of the front bumper, in line with the GTI emblem is? The other day I noticed that it appeared to have popped out slightly. I push it back into place, (it snaps into place) but i again noticed today after my commute home it had slightly popped out again. What does this cover and has any experience of it popping out?
View 14 Replies
I need to replace the center mesh grill on the front bumper. Is there anything I need to be careful with or watch out for. when I pull on the old grill or when I push the new one back into place? Does it come out easily or is it tricky?
View 4 Replies
I know the front and rear emblems have holes behind them. Looking for pictures of the holes in the body of the car?
View 10 Replies
I have a 2011 F-350 that came with the 5th wheel prep package which has rubber, two piece hole covers. Every time I slide something out of the bed across these covers they pop off or come partly off. I don't have a 5th wheel trailer and no plans to get one. Having trouble with the covers and come up with a better cover that would stay on when sliding cargo in and out. I hate just leaving the holes open to collect things. I wonder if some sort of galvanized electrical box cover would work with some sort of mount system under it?
View 14 Replies
I need to mount a plate on front bumper and there are dimples for 2 holes. Do I just use self tapping screws here as I've read you don't need a mounting frame?
View 3 Replies
I recently purchased a used 2010 Prius. I noticed that there are two holes on the floor in front of the passenger seat.
View 4 Replies