The dash DRL indicator comes on most of the time when I release the emergency brake. It seems that other times it doesn't. It also seems the indicator turns off after about 20 minutes. Does this sound normal, or does it sound like I have an electrical issue?
View 11 RepliesHad this issue on my first Touareg as well as the replacement. When you pull the emergency release handle (firmly and all the way) it doesn't fully release the brake. You realize this when the vehicle begins moving and you get the "Release Emergency Brake" message in the MFI.
They replaced the emergency brake assembly. The service rep told me before he returned the car to me that his tech was less than satisfied with the design of the hydraulic assembly and that he expected it to develop the issue again. He was right. Two weeks later the thing is sticking again.
I don't have the Touareg with me today (I guess I don't most days anymore, but that's another story...) so I don't know if it's int he manual, but this weekend while futzing around with the hitch wiring install, I noticed a small rubber ring/release belowthe CD changer area that stuck out into the little cargo cubby hole. I pulled it and the gas door opened.
View 6 RepliesOkay let me start by saying my car is APR Stage 1. The other day I was driving with my cruise control on and held in the accelerate button to speed up. After holding in the button for a couple seconds the check engine light and battery light flashed back and forth as if I changed some setting with the tune. Ever since that happened, if I turn the TCS off, the emergency brake light comes out and the error message 'check brake pads' is displayed on the MFI. Also, the weird part is that it's not just the light. The actual emergency brake is slightly on without pulling the handle. I can feel it when I accelerate. It's harder to get the car going. Once I turn the car off and leave it off for a few hours it goes back to normal. Why this is happening?
View 1 RepliesWhile the emergency brake was set, I happend to lean against the rear driver side of the the car and was surprised to hear a clanking, slapping noise coming from underneath the rear of the car; seemingly near the left rear wheel. What I think I'm hearing is the emergency brake cable (I assume this is a rear wheel cable brake) slapping against the vehicle frame or wheel axle. Even opening and closing the rear passenger door caused the cable to slap against the car.
This got me to experiment a bit, so I rocked the car back and forth and side to side. It's the side-to-side movement that causes the noise. The emergency brake works when set. The noise disappears when I release the emergency brake.
I have a stock '13 GTI with halogens and standard (non-LED) tails.
In VCDS, I coded the CECM to enable the brake light flashing under panic braking and also enabled the activation of hazard flashers under panic braking. Coding was accepted, no issues.
However when I did a driveby test yesterday with a friend watching, neither feature activated. I stomped on the brakes as hard as I could; ABS definitely engaged. So I was wondering a couple things:
Is there a minimum speed required before this will engage? I was probably going only about 35 mph when I hit the brakes.
Does this feature (at least the flashing brake light portion) require LED tails or will it work with the regular tails?
Looking on youtube videos of people who have activated this, it appears that they have both the flashing brake lights and flashing hazards activated at the same time so it would seem that's allowed by the CECM, yes?
Found a screen shot of the VCDS screen to show what I did:
I enabled BOTH bit 1 and bit 2. Some of the research I'm doing seems to hint that I should only be selecting one or the other?
My caliper gets seized when I disengage the emergency brake.
View 8 RepliesI have a 2000 VW Jetta GL. A few weeks ago I noticed my charging light come on followed by abs and airbag lights. Which would mean that the alternator is not charging the battery. However I kept on driving and this light would go off. However when I hit a bump on the road this light goes off meaning that the battery is being charged by the alternator. I recently installed a sound system in the vehicle which worked without problems for a few weeks before I started having this problem. Since then I have changed the alternator, battery and taken out the sound system. I now have a 125 amp alternator instead of a 90 amp alternator. The charge light doesn't come on anymore after startup but the abs, airbag and emergency brake light with a beep is now occurring.
View 3 RepliesI have a VW Jetta 2012 and I would like to know how to take out only the leather from the Emergency brake handle as shown in the picture.
View 1 RepliesReally enjoying my first Lexus RX350, but there seem to be some noise issues...
1. When shifting the gear, especially in the morning, from P to R, it is not smooth making some annoying noise. Is this normal?
2. Also, when releasing the break, there is some sort of a "thump" noise.
Don't think it is a big deal, but just wondering if these are considered normal.
I recently noticed that when I release the parking brake on our new 15 F-Sport it make a loud noise. It's hard to explain, but it kind of sounds like a spring being released with a clunking sound. (Sorry for the weird description).
When I press the brake to set it I am not pushing it all the way to the floor or forcing it at all. I am just using normal pressure to apply it.
It's a 2003, 2.0, rear disks. If I take it apart and manually compress the piston with that rotating clamp that Autozone lent me I can put it back together and use it 2 or 3 times and then it's too tight and I have to take it all apart again. I don't have the cable hooked up, I just move the lever with my hand or a screwdriver.
I'm a little irritated cause I replaced this caliper last year. I remember finding a good description of how this device worked and now I can't find it again.
Is it all the lexus rx350 had that noise? From the day I noticed hissing noise when I gentally press the brake pedal down and release it . And same noise can be heard when drive slowly and release gas pedal.
View 10 RepliesI went test drove a R32 today and I noticed when the headlight switch is in the off position, the HID came on when I release the hand brake, is this normal? I thought the DRL suppose to be the inner two halogen lights not the HID. This way, having a switch is kinda pointless except to turn on/off the the instrumental lights because you have the HID on whenever you release the parking brake, doesn't matter if the switch is in the off position or the on/lowbeam position.
View 12 RepliesQuick background. 1+ years ago I'd sometimes get the "moo" when in reverse. It was intermittent and never enough or a persistent issue to address. Recently, no moo, but I noticed when I'd release the parking brake and move forward there'd be a minor hesitation and an audible thunk, not too pronounced, then it'd roll freely from then forward.
Replaced rear brakes a few weeks ago, noticed the right side parking brake arm doesn't reset as far free as the left. Pushing it 'home' by hand made a little thunk in the cable house up near where it bends towards the vehicle's midline. Brakes installed, and it spun freely by hand with perhaps only a very small amount of 'hiss' but not consistent for a full revolution, only periodically. Lubed both cables from the center console.
Last night installed parking brake return springs, set and released the parking brake a few times to see how it felt. Right side looks like it still does not return home 100% (maybe, 2-3mm away, same as before). Today, made a run to Napa. Got there fine, when leaving, drop the parking brake, and as I'm grabbing reverse I get a yellow dash light and a "check brake pads" warning. I drove about a block, pulled over, shut off engine, got underneath (no parking brake set) and the arm seemed to sit about where it should. I drove a few miles at low speed, pulled over (left engine running, set parking brake), checked temp of all rotors (both sides) with my finger, nothing noticeable. Drove a few more, repeated the above (engine running, brake set) and temps were still cool.
Got home, replaced fans. Started up to test fans, and the error isn't there now.
If it was going to throw an error I'd more likely expect it when leaving home, where I had cycled the parking brake handle multiple times. No error there, or en route to Napa. Leaving Napa, parking brake engaged only once, I got the error. Powering off and restarting, it was still there. Successive stops did not have the engine shut off. Once home, it cleared.
I had not driven the Prius in a few weeks, and even then, that was for less than five miles, and had the low tire pressure indicator come on late last week when the temperatures cooled down, which I fully expected given my opportunities with the Toyota Dealer properly inflating tires. We were away for another week and returned today and I decided to check the tires and add air, and in addition to the tire pressure indicator, the ABS, Traction Control, and Brake Indicator lights were on. As soon as I filled all the tires to the specified PSI, that indicator disappeared but the brake related ones all stayed on.
View 10 RepliesThis has happened twice now, about a month ago and then again today.
I was stopped at a light with my foot on the brake. There is a clunk noise, then the indicator light comes on.
The first time I tried to go, and the car stayed put. I hit the parking button, then went back into gear, no problem.
The second time I just put it in park and then back to gear. No problem.
So I noticed this has happened a few times.. If I press on the brake pedal too hard, the indicator light will come on and then turn off a few moments after I depress the brake pedal. This has happened when the car is stationary as well as when I was coming to a stop, it's happened maybe 5 times since I picked the car up a few weeks ago. Is this normal behavior or an indication of a problem? Just an FYI, I'm not talking about when the indicators light up when first starting the car.. This is tied strictly to pressing the brake pedal hard.
View 8 Replies2010 Prius V owner as of last week. All has been going well and got into the car this morning and all of the above noted lights are on at start-up and stay on as I drive. Have made appointment with the dealer but they cannot get me in until late next week. I did make a short drive this morning and all seemed fine with handling and braking. Searched a few threads here and answers are very varied and none that I saw had all of above lights on. I don't think that it is the Hill Start Assist. Safe to drive until we can get into the dealership?
View 14 RepliesSo, according to my wife, there has been an indicator that the brake fluid is low, a couple of times, over the past several months.
Now, I know pretty much nothing about brake fluid, since it is usually simply changed at specified intervals. My mechanic might have not filled it up to level at the last service - there is no indication of leaks, especially since the warning is rather sporadic.
My wife went and got a bottle of "Prestone DOT 3 High Temperature Synthetic Brake Fluid." Will that do? Any precautions?
And yes, this is for my 2010 MT Golf TDI.
My "Check Brake Pad" sign lit up yesterday. I check the pads with out taking the wheels off around. I am still on OEM original rotors and brake pads. The car has 35,000 miles.
Both rears looks fine with about 3/16" left the fronts right side and left side has the lowest at 1/8". Do you think i can still use the rotor one more time before i replace them or should i replace them with the pads?