Gmc - Sonoma :: 1997 - Code P0300 / Misfiring
Jul 16, 2011
I got a 1997 sonoma which has a p0300 code. I changed the plugs and wires, cap and rotor and the pcv value, and it still misses. what could this be?
View 18 Replies
Jul 16, 2011
Advertisement
Golf/GTI VI :: Misfiring - Code P0300 And P0302
I have a 2011 GTI (purchased new in 2010) with a stage 1 APR tune and a carbonio stage 1 intake. 71K miles on the car, tune has been on it from nearly the beginning, no issues. I have religiously filled with 93 octane gas -- like, always. The other day I was filling up an empty tank in NJ -- land of mandatory attendants -- and I accidentally said "premium" instead of "super." (I normally self-serve in PA). Before I realized what had happened, I had a full tank of 91 in the car.
I run the 93 octane program on my APR, and I couldn't remember how to switch, so I've been running around the last few days that way, seemingly with no issues. I'm not even sure what's supposed to happen if you burn 91 while in the 93 program.
Anyway, yesterday I happened to go full-throttle in 1st or 2nd gear, and I ran into a little stumble. Strange, but I figured maybe this was the result of my refueling mistake. So, I got out my APR manual and figured out how to switch programs down to the 91 program, which I then did. Took the car out again, and was still able to get it to stumble, eventually with a blinking, then solid CEL. A quick VCDS check showed a "Random/Multiple Cylinder Misfire Detected" -- P0300 and "Cylinder 2 Misfire Detected - MIL" -- P0302.
Now at 71K miles, I've never replaced the coils or the plugs, although I have had 2 intake manifolds replaced under warranty. I'm kind of figuring the octane and tune are not really causing this and it's probably just in need of some coils/plugs. what is "supposed" to happen if you run 91 octane on the 93 program? I haven't tired backing down to stock yet, but I could certainly do that and see what happens.
Golf V R32 :: Getting Code P0300 / P0303/ P0306 - Misfiring?
Went to do a few things this morning, started the car and it ran like crap. It was an obvious multi cylinder misfire. I checked to make sure all the coil connections and all other visible connectors were tight. Went back around and noticed the mil was flashing, so I shut it down and took the girl's car. I returned later in the afternoon and swapped out my intake in anticipation of it going to the dealer. Started up the car afterward and it ran fine without the mil lit. I had the codes pulled:
p0300 p0303 p0306 Its kind of weird that 2 coils would go at the same time. Do these cylinders share a coil or fuel injector driver off the ecm?
Chevy - K1500 :: 1997 - Code P0300 Rough Idle
97 chevy k1500 with 305, engine rebuilt by shop 60k ago, last few months only drove truck 4-5 times, last time driving gave p0306, new plugs, wires, cap, rotor, cleared code, now gives p0300, took intake apart removed spider, sprayed/scrubbed each injector and poppet with cleaner, but no way of cleaning the line between the injector and poppets. No change after cleaning. Also ran injector cleaner through tank. All vacuum hoses look in good order, sprayed carb cleaner around intake to check for leaks at intake/throttle body, no leaks.
Checked TPS, IAC, MAF, Coil and fuel pressure, all good except fuel pressure was 52-54 while idle, replaced fuel pump, screen filter and main filter, cleared code, rough start and rough idle still gives p0300. Checked coil with ohmmeter, between posts A & C, Chilton says 0.1 ohms, i got 0.5 ohms, went to autozone and had them check a new coil, it have 0.5 ohms......? Can drive at higher speeds and runs smooth, but idle is poor almost dies.Checked fuel pressure after pump replacement, still ~54 psi. Stumped and don't want to throw more parts at it without a proper diagnosis. Have a OBDII pocket scan tool, but can't find manual, will try to find manual and see if I can pinpoint the misfiring cylinders.
Accent MC (2006-11) :: 2007 - Misfiring Codes P0300 And P0302
My girlfriends 2007 accent as thrown codes p0300 and p0302.
After reading everything I could find, I had coil pack on my list of possible problem items.
The car sat in the driveway yesterday and when she went to start it today, she couldn't get it to.
I got it to start when I got home by giving it some gas while turning the key, but I don't want to drive it anywhere.
The hard start is leading me to believe it's the coil pack.
I was going to start with changing the pcv, spark plugs, and run fuel injector cleaner through it because those are the cheap possibilities...but now may add in a new coil pack.
Santa FE SM (2001-06) :: 2002 - Misfiring / Codes P0171 And P0300 Came Up
My car is misfiring, codes p0171 and p0300 come up on the code reader. It idles rough and has very little power. I have checked my exhaust , it is not plugged. When I unplug coil #2 while idling there is no change as to the engine performance so I switched the coils around with no difference when coil is unplugged on cylinder #2. I have changed the plugs, there is power to the coil, all plugs are firing and when removed plugs 2 and 3 are wet with fuel indicating I am getting fuel and fire. I have replaced the cam sensor with no change.
View 3 RepliesPassat (B5) :: 2001 - Misfiring - Got Codes P0300 / P0301 / P0302 / P0303?
i have a 01 passat with a v6 in it on 4 motion and im having an issue with soem mis-firing
i pulled the codes. P0300 P0301 P0302 and P0303 which are all saying that there are missfires in cylander 1,2 and 3 and random miss fires.
im also getting a P0340 which is cam sensor A or the right hand bank. problem is i just replaced the cam sensor and when the motor got warm, the code came back. I was told by the previous owner that the car needed a Coolant Temp Sensor....can this be the cause of my mis-fire issue? hear me out.... it only happens when the car is warm so im thinking that the car is warm but the ecu thinks its cold cause its not getting a good signal from the CTS. thus its either advancing the timing as if the motor is cold and cuasing a miss fire or something along those lines. any thoughts?
GMC - Sonoma :: 1997 - Transmission Died - How To Fix It
Just had a quick question in regards to my Sonoma. My 97 Sonoma 2.2l transmission died on me a few weeks back and i happen to have a working 4.3L transmission from an old 2000 Sonoma i once had. My question is will it work? Am I able to bolt the 4.3L tranny to my 2.2L engine? and if they would is there anything else I would require to make it work?
View 7 RepliesGolf IV / Jetta IV :: Getting P0300 Code?
Yesterday I went to star my 2.0 Jetta and it instantly starting sputtering at idle. After maybe a minute of sputtering the car died. Tried restarting it and it would instantly die after starting. Car threw code P0300: Random Misfire.
As of today the car now runs again with no problems. No codes. I didn't touch a thing and it seems to have resolved itself.
The entire engine bay was wet from condensation due to temperature change. Is there any way this could've contributed to the misfiring? I'm thinking the spark plug wires might have gotten wet and that was causing the misfire.
Camry :: 2002 - Intermittent Misfire Code P0300 / 301 And 302
I've got the intermittent misfire codes on my '02 Camry, and after changing the spark plugs and the ignition coils the problem still persists.
At first there was no noticeable misfire, I took it to two different mechanics and neither said they could find anything wrong. A few weeks later the misfire became noticeable when I'm sitting at a stop light. I can feel an occasional rumble in the engine.
LS / MKZ :: 2001 - Loses Power Under Loads / Code P0300
I have a 2001 ls that runs rich and shows no codes except p0300. It will miss under loads and get worse as temp rises. I can smell exhaust and burns eyes when running inside shop.
View 2 RepliesPhaeton :: 2006 - P0300 Code On W12 / Intermittent Misfire
I took my 2006 W12 to get its yearly smog check, and it will not run "air" monitors due to intermittent misfire. The code is P0300.
Any way clearing this up? (I could find no air leaks)....
Prius (2004-09) :: CEL Code P0300 After Replacing The Air Filter
My CEL has come on about four times in the last month shortly after replacing the air filter with a pepboys Purolator air filter. I have cleaned the MAF sensor each time using MAF cleaner and the issue along with the CEL go away then come back in about a week.
I don't know if the MAF sensor is bad because each time i clean it, the issue stops. also, upon first glance at the Purolator filter, i thought it looked a little thicker than the stock one but I didn't think twice about it.
TrailBlazer :: Random Misfire And Code P0300 - Rough Idle
'02 TB w/ code P0300 / Random misfire. Started the other day when it was very damp out, FWIW. Feels like ur driving on rumble strips during acceleration. Rough idle also. It does not do this continually though as after a while (minute) it clears up and runs smooth for a while then runs rough & light will again for a while. I seafoamed it today since it been about 60k since last seafoam. I thought that might have worked until I drove about 20 mile and it went rough again. I also cleaned the oil out of the cam sensor elect connector, since that caused rough running before, although it didn't throw that code. It seems to be very intermittent. '02 TB, 185k miles, orig plugs changed at 125k. Is it actually just going in & out of a limp-mode? O2 since it's random ???
View 14 RepliesLexus ES 2013+ :: VSC / Engine / Trac Light On - Code P0300 Only
I had a check vsc, engine light, and trac light come on... I got the code checked and it returned P0300 only. That was three days ago (5 totals days of the lights being on) and today I start my car up, and all the lights are off.
I've only had my 2007 ES 350 for 5 months. I bought it used with 48k miles on it. I'd been advised it probably need new plugs since none of the coil codes hit... should I still be concerned? should I still replace the plugs although the lights have gone out?
Suburban :: 2000 4WD - Code P0300 Misfire Only Occur At Idle
I have a 2000 Suburban 4wd that has a p0300 code. The misfires are coming mainly from #2 and #7 cylinders. Misfires only occur at idle. over 1500 rpm the misfires disappear. I have put new A/C Iridium plugs in, new wires, and new coil packs on both cylinders but the problem is not any better. All 8 fuel injectors all go to 55 psi when activated and drop to 28 when released. All tests were done with my Snap-On Solus.
View 2 RepliesPrius (Gen 2) :: P0300 Code And Random Misfire - Car Shaking More Than Usual
Recently i started the car and it was shaking more that usual. the CEL light came stating P0300 with random misfires. It sounds and feels like misfires so i believe this is true.
View 10 RepliesGMC - Sierra :: 2004 - Code P0300 Random Misfire While Under Load
2004 GMC Sierra 2500 HD, 227,000 miles 6.0L V8.
While driving up hills or increasing load, the CEL will flash multiple times, I pull over as I know CEL flashing is not good. I turn the truck off, allow it to sit for a few minutes, whip out the code scanner, only code that was there happens to be P0300. Truck has poor MPGS, idles rough, loss of power. this happens every time I drive this vehicle as I use this truck to pull my trailer that weighs around 4000 lbs. Problems come and go. Some days I can drive the truck for an hour with no problems, come up to a red-light, BAM, CEL is flashing, truck is bouncing side to side due to the poor idle, other days this happens while sitting in the parking lot of my job with the ac on.
Truck has been to the shop several times as I'm no mechanic. Parts replaced are as follows:
- Fuel pump
- Throttle Body
- All plugs
- All wires-All Coils
- Intake Manifold Gasket-
- Battery
- Sensor 1 Bank 1 O2 Sensor
- Sensor 1 Bank 2 O2 sensor
Sonata NF (2006-10) :: Code P0300 - Multiple Misfires On 2009 V6 3.3l
I am trying to get a 2009 Sonata NF with a 3.3L V6 to run correctly and i have tried everything that i can find and still get the problem. The car runs very rich with a strong gas smell. The engine runs rough but doesn't stall. The car has has period where it runs fine and then the issue returns but is in more frequent and steady now. The car will run for the first 5 minutes great if it is cold and it also runs good at full throttle and the check engine light went off during hard acceleration which seems consistent with getting too much fuel. I bought a BlueDriver to read the codes and I love the data it provides but I am learning all the features.
For a little history the car has 95,250 miles. At 81157 miles the check engine light came on and an independent shop replaced the downstream O2 sensor and the light has been off for 2 years until coming back on recently. The code showing was a P0300. The shop replaced spark plugs and the manifold gasket with and oil change for $775. The check engine light stayed off for about a month and 550 miles. The car was taken back to the shop and they replaced the rear O2 sensor for $429 . The check engine light was off for a couple of days and then returned with the P0300. It might go a couple of days without a problem and then it would return.
This is when I got the car and started reading all the forums i could for possible causes. I saw the Tech Bulletin on the Variable Valve Timing Oil Control Solenoids so i replaced both valves. The check engine light returned with a P0303 for cylinder 3 misfire so i figured it was a coil so i replaced all the coils. The P0300 code returned. I check fuel pressure after seeing a post about fuel pressure regulators causing the problem but the pressure was correct. I changed the Mass Flow Sensor figuring it was getting too much gas but no improvement. I bought the BlueDriver so I could see more than just the codes. The O2 sensor looked erratic so i changed the front upper O2 sensor.
I found the Tech Bulletin about the O2 sensors fuel trim readings and realized there was an upper sensor on the back manifold and it was reading -18% so i changed it and now I don't know which way to go. I currently have the P0303 code confirmed and P0300 pending. With the live data the items that looked strange at idle were O2 Sensor Bank 1 Sensor 2 steady at 99.2% and Calculated Engine Load a 21.6%. The freeze frame data from when the light came on has all the short fuel trim at 0.0% and long term at -0.8% for both banks. Calculated Engine Load was 45.9% even though I was trying to drive slowly at 29 mph. Mass Air was 21.71 g/s, I had been running 3 minutes from a slightly warm start, Absolute engine load was 44.3%. Anything else to check or data I should look at?
Santa FE SM (2001-06) :: 2004 3.5L V6 - Random Misfire Code P0300
I have a 2004 Hyundai Santa Fe 3.5L V6 when i was driving a couple of days ago the check engine light flashed and after a while it stayed on the codes are P0300 which is a random misfire as well as a misfire in cylinder 2, 4 and 6
I replaced all 6 spark plugs and the 3 spark plug wires still the same issue. The car hesitates when accelerating when i accelerate it looks like it wants to stop the rpm goes to almost zero and then it moves and so on. the rpm goes up and down like crazy.
Sometimes it won't move past 1000 rpm I'm moving 60mph and still on 1000rpm and sometimes it works just fine like there is no issue at all. When idle the car is fine and everything seems normal it stays on 900rpm. The car has 158K miles on it.
I uploaded a video to show you what's happening to the tachometer when I accelerate [URL] ....
I'm on a limited budget I'm thinking of changing the ignition coils but i want to make sure that's what is causing the problem first because i spent 200$ to change spark plugs and wires and the mechanic didn't fix the issue.
Saturn - Cylinder - Vue - Misfire :: 2005 - Steady CEL Code P0300
2005 4cyl. Vue with 54K... Steady CEL. Runs great. Absolutely no problem accelerating. Don?t hear or feel any misfiring. There is a slight rumbling sound when I first start to drive the car, but to me, the sound doesn't seem come from the engine, but rather underneath the car. It goes away when I continue to drive. Since winter began, I occasionally feel a very slight hesitation during idle?happened once or twice lately.
Again, I only feel justified in mentioning it simply because of the codes that were generated. None of my passengers have made a comment about the idle or the drive. My friend, however, made a remark that occasionally, there is a very very very slight hesitation at the downshift when braking. No crack in gas cap. Great fuel economy. No problems accelerating at all. Never hear or an actual misfire, which I take it, means a problem when accelerating, a jerking, or popping noise.
Took it to a dealer. Codes were 0300, 301, 302, 303, 304?302 generating most often. Dealer recommended new ignition module and plug replacement, but they said it wouldn?t be a guaranteed fix and that it may need EGR replacement (don?t hear knocking though) or be a burnt valve in the cylinder. No suction out tailpipe, no rotten egg smell (signs of burnt valve). What are the chances of burnt valve in a car with 54K anyway?
Also, my maintenance schedule claims that I don?t need new spark plugs until 100K. Is there anything else this could be such as a dirty injector system, fuel filter, fuel pump, or air filter? Again, overall, the car runs GREAT! Should I just wait and see if the misfire becomes more pronounced so when I take it to a mechanic, they won't be looking for a needle in a haystack?