I have a 20th 1.8t. It was running fine last week but all of the sudden i was only getting about 4-5 psi. I have check all over vwvortex for somewhat of an answer. I have no C.E.L.. I have checked for vacuum leaks with nothing coming up. I tried to check for boost leaks but it comes out of the dipstick hole. I have undone and re-installed the pancake pipe. The DV is holding pressure.
View 1 Replies02 GTI 1.8T ... Stage 2
Was running the car at about 4500 rpms in 5th gear. All of a sudden lost power and heard a loud whooshing/ hissing of air which sounded like it was coming from under the front passenger side of the car. Lost about 50% of power in all gears. What I screwed up and broke?
I'm to the point of driving the car off a cliff! I've included a log of the car acting upt. The car is a 20th AE GTI AWP. It was chipped all it's life and ran like a champ. In November I installed a Frankenturbo F21T turbo kit, Bosch EV14 550cc injectors, 3" MAF, eBay FMIC, 3" catted exhaust, and a custom tune from Motoza. Dave at Motoza has updated the file 4 times and no matter what he changes, the car will boost up to the requested boost of 19psi and hold it for almost one second, then boost will drop to 12-15psi and then boost past the request to like 22-24 psi and go back and forth until the gear is over and I shift. Then it does the same thing in the next gear. i just want a solid 18-20psi without a manual boost controller! Things I have tried:
-Changed the N75J back to a NEW stock N75
-Replaced all the N75 vacuum lines
-Wastegate cracks at 7-8psi
-Replaced every worm feed clamp to a nice T-bolt clamp
-Boost leak tested to 18psi and found no leaks
-Deleted SAI, N249, and N112
-Unplugged MAF, nothing changed
LOG with multiple WOT pulls: [URL]...
when the traction control is off my boost hits 18psi and there have been times where it was 20 psi. My friend said i probably have stage 1 software .
View 4 RepliesStart with the basics, no CEL's, car has not cut out while driving and I've only had to attempt cranking up the car twice since I started noticing these issues about 6 months ago.
Symptoms: hesitation/variation in boost during acceleration- doesn't matter if I really get into the gas or just "normal" passing acceleration RPM's steadily climb, but just not as consistent or quickly. Also, the one that really has me really confused. With a 1/4 tank of gas or less, going up a slight incline (overpass); 70-mph-ish... acceleration dies off, rpm's slowly decline, and gas pedal doesn't respond for about 2-3 seconds. Car never shuts off, no CEL's, then everything is fine again! Even does it when I'm using cruise control. Car just rolled 110,000 miles
I'm not sure what to make of this ... I disconnected the battery before installing . The gauge seems to be reading correct based on what i researched. If there was a slight leak would it throw the CEL ? is it maybe just a one time thing that needs to be cleared afterwards ? Car drives fine and I plan on trying to stop at autozone to get there crapo freebie scan . Kinda annoyed considering everything went smoothly up until I drove the car more then 50 miles .
View 14 RepliesSo I have a 20th AE with 113k Miles.
All of engine is stock, but when I FLOOR it from about 3rd-4th or sometimes 2nd-3rd the car will build up boost but release it without me letting go off pedal.
So, basically as I am driving the car sort of builds up, drops, builds up, drops without my doing anything but drive.
It will rev to about 3k stop for a second, rev to 4k stop for a split second, rev to 5k and so on... Not sure what this is or why it could be happening...
Having trouble with car going into limp mode or just not boosting at all. Tried some basic things to fix it, plugs, coilpacks, tune, none have work.
View 4 RepliesSo I just installed a boost gauge. Vacuum line is running off the fuel pressure regulator. My boost is now not going over 10 psi and the engine is cutting out. It kinda feels like the dv isn't holding psi but just always open. The car is a 05 gli with intake and exhaust.
Also the car seems to be running alright at below 2000 rpm and it just starts to cut out when it should be making boost. And I'm pretty sure this car is reprogrammed because yesterday when I finished the boost gauge install it was running at19 psi.
For some reason My car won't boost like it used to in the upper gears. 1st, 2nd and even 3rd I can still boost around 18 but once I go 4th, 5th, 6th my boost get lower and lower to the point the I get only 10psi in 6th gear. The car also seems slower a doesn't spool that fast like it used. i checked most of the hoses, even my intercooler pipes which were leaking before and everything is tight. Could it be my DV which is still stock or should I look someplace else?
View 13 RepliesWhen I hit the gas and my turbo reached high boost (15 psi and up), it would slightly sputter and make an odd sound. I even noticed my exhaust made a different exhaust note than usual. While it sputtered the CEL began flashing. I then drove it normally (not high boost) all the way home and it drove completely fine. I'm gonna try and get my codes checked tomorrow.
View 9 RepliesCar now has about 67,000 miles on it. I drove it from the bay to Lake Tahoe 2 weeks ago, which is when I first noticed the light. I tried to go to a couple of autozone's to get the code read but none of them would do it. I also noticed that now on my boost gauge that i am only reading 4-5psi under load, so its not quite feeling like i'm getting as much power as before. What a common issue is at about this many miles on a 1.8t car? (GLI)
View 3 RepliesIf your diverter valve is bad, will it throw a CEL or not always? I don't have a CEL but sometimes I feel like there is a lag in the boost. Wondering if the diverter valve is bad or not.
View 6 RepliesSometimes while driving if i accelerate the car fully the rpms will accelerate way to fast (at least 2x faster than usual) without picking up much speed at all. I can tell that the car is not going to full boost. The problem is the worst in 5th and 6th gear (when the car is relying more on boost im guessing?) and will happen one day and be perfectly fine the next. I just had the car checked for a boost leak about 3 weeks ago so i dont think its that. The car is chipped with uni stage 1+ (20psi) and has a full 3 inch turboback.
View 15 RepliesI installed a brand new "A line" 007 last night. Now I have ridiculous boost surge (15psi then to 5psi, then holds 11 hard) I did a N75 race valve last year (ECS), so I have my doubts that it is the N75. So what gives? The car wasnt that bad with a blown stock DV compared to this. I have minor mods: CAI, exhaust, Forge TIP, APR stage 1.
View 24 RepliesI've had this problem a while but now i want to get around to fixing it.. my boost gauge is always at 0 now and sometimes when i drive the car it starts working but it starts like sticking... like when i didn't have my chip it would go up and down really fast between 10 - 15psi... i heard from a friend that you can take it apart and re-adjust some screws or something so it works like a charm... right now its just like frozen at 0 psi when i drive it doesnt go down or up.
View 4 RepliesWas driving the other day and one of the couplers came loos and I lost boost and went into limp mode. I pulled over, got it reattached, and after that it would only hit 10 lbs. i have a KO4-001 with the GIAC file and it usually hits 20+ and holds 20 lbs. I have a regular code reader and I had a code for the EBC, cleared it, rechecked the hoses, and verified with the flash loader that I was on the correct file, but it is still only hitting 10 lbs. What else I should check.
View 1 RepliesThere ended up being 6 or 7 codes. Originally the first O2 sensor and wire seemed to go bad, I replaced them and it ran well for a couple days and then started running like ass again...Now there are a few codes, none for the 02 sensor, but for over boost issues...Does this mean my n75J valve is causing the problems? Is it possible that my software is just going bad? ...I bought the car somewhat molested and don't quite know the extent of the parts on it, nor the brands( specifically, the software...).
The current codes being thrown:
P0238 mani pres g31 sig to high
P0234 overboost
P0106mani barometric sensor g31
We replaced the manifold pressure sensor, and am not having the issues but they could and probably will come back after 50 or so miles...Previous code also was P1114 02 sensors and we replaced the front sensor. It may be that the software that is on the car is starting to go..
I am running the GIAC X+ 93 octane tune with a cold air intake and when i hit full boost it fluctuates from 20 to 15 through out the gear. i am guessing its because of my stock dv. im looking in buying the eurojet dv.
View 13 RepliesPreliminary info:
APR 93 tune
Carbonio Intake
Silicone TIP
I picked up my 20th today and drove it 4 hours home. It has 74k on it, original timing belt. The timing belt kit is in the mail on its way here. Its the first thing I'm doing.
As I was driving it home on the autobahn doing about 150k/hr and I gave it half throttle to pass, I felt the turbo spool and I accelerated past the car. However, when I went to make the next pass, it felt like I had no power. I feathered the throttle a bit and it felt like my car was only getting maybe 3 PSI of boost. Very little actually. I do not have a boost gauge so I can't really say it accurately. As I was driving, i shut the ignition off and turned it back on. After that, I was able to get full pressure back.
I got a 04 jetta gli that is making a loud blow off noise at around 15 psi. Up until then the the boost holds fine but then at around 15 psi it just starts whistling really loud and loses all boost. I recently replaced the DV and venthose by the camshaft, and made sure that it is tight. I also installed a 42DD 3" exhaust recently. The car has about 96k on it with stock vacuum hoses except for the aforementioned adjustments. I'm pretty sure it's not the hose and DV I replaced because I made sure that they were tight to see if that was the problem, and it did not fix it.
View 2 Replies