So, I just installed a ESE cold air intake on my gli...and when i shift it sounds like air is coming out of the intake. make sense? is this normal? Also, how high is the risk of a hydrolock?
View 15 RepliesI just installed a neuspeed ram air intake on my gli. I noticed that top end seems a little more sluggish. Is there anything i need to do? I have heard you should disconnect your battery for a few to reset your computer.
View 5 RepliesSo I dont have the money to but a new intake, I am having problems with water getting into my cold air intake under the car. What i could do or something cheap to buy to prevent this problem??
View 13 RepliesI am having an issue after my intake install, it was working fine all day and last night i get a light on the dash bored (looks like the one when you take off the esp) and I get this:
code 16485 Mass Air Flow Sensor (G70) Implausible Signal : P0101
Static - No
What could be the cause of this because i ran this intake before no issues I only took it off and put the stock intake back in due to the rain but now since the rain is gone i decided to switch
On my gti when in low revs, theres a rattle that sounds like a shield but I've check the one around that cat and the one under the turbo. but it still rattles. What this could be?
View 3 RepliesFirst off i couldn't get the car into reverse to back out of a convenience store and then i let off the clutch to try and pump it again and the car just dies. drove just fine up until i parked. Now when i try to move through gears it sounds like it's shifting but the car doesn't move. The car does have a stronger clutch and unitronic chip if that would have to do with anything.
View 13 RepliesI was randomly driving today and my turbo started to sound a little weird.
Every time i accelerate, turn it on or rev it up it sounds like a turbo diesel truck! I have no clue what it could be..
I have a 20th ae Gti. When i bought the car it has installed a EIP Short Shifter and it was working fine, But... Yesterday i cant shift to reverse. So i decide to take a look since that was the first time that i have a problem with that, i thought that was something wrong with the Short Shifter so i decide to see how to install the Short Shifter so i can Re do it all by my self and now i cant Find any gear, No reverse, no 1st no 2d not even neutral.
View 2 RepliesSo i went to start up my car after about an hour of not driving , (previously working fine) and I am not able to shift into reverse 1st or 2nd , ive been looking around and i guess the options are linkage, gear selectors, gear box or tranny.... Its a 337 so its a 6 speed . don't know if that makes a difference
View 2 RepliesYesterday I went to shift from 2nd to 3rd real easy going like 25mph and i couldn't shift out of second. I could wiggle the shifter up and down but barely side to side. Even when moving it up and down it didn't feel like it was engaged in any gear although it was apparent I was stuck in second. Clutch feels normal and still grabs well.
So after driving only in second all the way to my uncles shop I sit at school waiting to see where i can pour more money into the GTI. Its a 20th ae totally stock tranny, I don't know a whole lot about transmissions but possibly the linkage got messed up? I didnt hit any big bumps or anything before it happened.
How to remove the OEM "golf ball" shifter on a 20th AE? I tried everything but it still won't budge. Is there a trick to removing it? Is it a tight press fit or does it screw on?
I have the latest edition of the Bentley repair manual and it does not cover this shifter knob.
I was looking through the DIY and I couldn't find one that just removes the knob it self. I know its all the same steps to remove everything but everyone just swapped the boot and everything. I want to keep my boot and just change the knob to a solid glass ball.
View 1 RepliesI am having trouble shifting my 6 speed into 2nd, 4th, and 6th. I got my clutch replaced about a year ago, not sure if that makes a difference. Any fixes short of bringing it to a shop?
View 1 RepliesMine broke and needs to be replaced but i can't find any directions on how to remove it.
View 9 RepliesLooks like the 1-2 shift fork failed on my 337. This is the 2nd time this has happened to my car in under 100,000 miles of driving (I'm the original owner). The last time was about 3 years ago and the shop I was going to found a used transmission for me. Just curious, how common this happens to our 6-speeds.
View 4 RepliesI had my shift fork and 1 and 2 gear synchros replaced. Whenever i shift into second it doesnt feel as smooth as first. when i hold the clutch longer and put it into second it feels smoother.
View 2 RepliesSo there is an imowa 20th that im really interested in, 100k chip and exhaust. But there is a problem that could be a deal breaker
He says that 6th grinds when you go into it, it has no problem getting in but it makes a noise when you shift in, best guess is that its a synchro problem. This would not bother me so much if this wasn't an 8 year old limited edition sporty hatchback with a transmission unique to the standard gti.
So the other day was driving my car... And he said reverse quit working. I'm nowhere near my car right now, but it sounds like the same thing that it had done for me a few times. Basically, the gear shift won't go into the slot for reverse, and even first is hard to get into sometimes. Sometimes it works and sometimes it doesn't... My car's a 337 with an O2M transmission.
View 3 RepliesSometimes (most of the time), when I shift from first to second, its either hard to do or it "pops" into gear. There's not like a grinding gear but it sounds like it is hitting something as it goes into gear. If I go 1st to 2nd while stopped, it goes in nice and smooth. It sort of feels like how you can't shift into 1st while you are moving slowly, you have to push on it a bit and then it finally pops in.
View 8 RepliesPulling into work today and backing into my parking spot, a fellow employee noticed something odd about my front wheels, so he hopped in my car so I could see the issue.
From a dead stop accelerating forward, the front wheels shift a few inches to the rear, and same thing when backing up from a dead stop they shift to the front. Both sides are doing this evenly. I haven't thrown it on the lift yet but I was thinking a possibly bad dogbone mount. The car has 133K on it and the bone has never been touched.
It all started after it being cold outside it's hard to shift into second gear when i first start up the car, and then after a couple shifts like that i get a notchy shift. after a while of driving it all disappears.
View 3 Replies