GTI 337/20th Anniversary :: Sudden Low Boost - Soft Limp Mode?
Apr 9, 2010
Preliminary info:
APR 93 tune
Carbonio Intake
Silicone TIP
I picked up my 20th today and drove it 4 hours home. It has 74k on it, original timing belt. The timing belt kit is in the mail on its way here. Its the first thing I'm doing.
As I was driving it home on the autobahn doing about 150k/hr and I gave it half throttle to pass, I felt the turbo spool and I accelerated past the car. However, when I went to make the next pass, it felt like I had no power. I feathered the throttle a bit and it felt like my car was only getting maybe 3 PSI of boost. Very little actually. I do not have a boost gauge so I can't really say it accurately. As I was driving, i shut the ignition off and turned it back on. After that, I was able to get full pressure back.
View 6 Replies
Advertisement
Having trouble with car going into limp mode or just not boosting at all. Tried some basic things to fix it, plugs, coilpacks, tune, none have work.
View 4 Replies
Was driving the other day and one of the couplers came loos and I lost boost and went into limp mode. I pulled over, got it reattached, and after that it would only hit 10 lbs. i have a KO4-001 with the GIAC file and it usually hits 20+ and holds 20 lbs. I have a regular code reader and I had a code for the EBC, cleared it, rechecked the hoses, and verified with the flash loader that I was on the correct file, but it is still only hitting 10 lbs. What else I should check.
View 1 Replies
There ended up being 6 or 7 codes. Originally the first O2 sensor and wire seemed to go bad, I replaced them and it ran well for a couple days and then started running like ass again...Now there are a few codes, none for the 02 sensor, but for over boost issues...Does this mean my n75J valve is causing the problems? Is it possible that my software is just going bad? ...I bought the car somewhat molested and don't quite know the extent of the parts on it, nor the brands( specifically, the software...).
The current codes being thrown:
P0238 mani pres g31 sig to high
P0234 overboost
P0106mani barometric sensor g31
We replaced the manifold pressure sensor, and am not having the issues but they could and probably will come back after 50 or so miles...Previous code also was P1114 02 sensors and we replaced the front sensor. It may be that the software that is on the car is starting to go..
View 2 Replies
So I have a bad map sensor and lately my turbos been going in and out of limp mode. I recently just replaced with a new n75 valve and it solved the problem for about a week and now it's acting up again. Its not a constant problem it occurs usually every 20 starts. Could the map sensor be the reason why my car is going into limp mode?
View 4 Replies
I got a quick question about limp mode. I know this has prolly been covered a few times but I couldn't find anything too similar. Well, to start out my car cannot boost past 3lbs. If i turn the car off and take the terminals off the battery and let it reset for a while, it goes back to normal for a while. After a few times driving it, limp mode comes back on.
The first time this happened, the check engine light came on also. But once I reset the battery it turned off and went back to normal. But it never stays away for good, limp mode always ends up coming back...
View 9 Replies
I got this car (03 gti 20th a/e) a few months back, and days after taking ownership it started having issues. the one that's still present is related to the boost. Every time I go to accelerate and hit 15-17psi the car sputters, and sounds like a popping noise under the hood..followed by the car going to 5psi for a few seconds, and the engine light flashing (then goes to solid cel).
The car has been scanned for the cel and it had thrown a number of codes-all have been addressed..but still have the same issue!--misfire in #3. I have had a local shop that only works with vw's & audis do all the repairs. we have replaced the coil pack, the spark plugs, and the N249 boost valve. The car is still showing a misfire in #3. What could be the issue? Maybe its the tune?
View 11 Replies
I have a 2004 1.8T AWM auto tranny Passat with APR chip. CIA, Bolt down Coil Packs, Bosch F6DTC plugs, OEM cat to straight pipe to magnaflow muffler, N75J, Forge DV (not the 007).
I installed a MBC bypassing the N75 to keep the spike at 16psi and hold (the n75J i spike at 22psi and hold 12~14), When I did that, the car will go in limp mode from 'over boosting'. I have to turn the MBC down to 9 to keep the car limping out. I love the way the MBC have the boost curve (the N75 is too passive for me). would like to fix this issue.
Also, with the N75 and or MBC, while in the APR 93 oct chip mode, I always get surging in 4th and 5th gear. Any time the boost is over 10psi, it is like I have tons of boost, but the engine is not using it. APR said it is the tranny, the tranny shop said it is the engine or computer, the engine shop said it is the tuning.
View 1 Replies
I currently own a 2001 Jetta 1.8t. It is currently tuned for 15 psi supposedly. I have never seen that number been hit and the highest it will go(only in 4th and 5th gear) is 13-14psi on a good day. And even when it does get there it does not hold the boost what so ever. It will start losing boost almost as soon as it reaches those numbers. Another thing is my MAF is currently unplugged and is making my car throw a code. When MAF is plugged in it cuts out boost and goes into "limp" mode.
Here are some engine mods that may be apart of this issue:
- Front mount intercooler, full intercooler pipe kit
- Oem diverter valve
- N75 j valve
- ACHTUNING tune on 15 psi not sure which stage
- Forged turbo inlet pipe
- 032 motorsports crankcase breather hose conversion
- Ecs tuning
- 2.0t coilpacks and mounting plate
- AWP head
View 3 Replies
I have been battling a big boost upon acceleration at stoplights for approximately 6 months. Now twice I have gone into limp mode and the tech reads: PO700 (Transmission) and PO731 (Gear 1). I just turned over 190,000 miles but only purchased it a year ago. What is the problem(s)?
View 1 Replies
We were headed home the clutch pedal went soft... Ok, I thought it's either the clutch master or slave. I get it home and replace the master and after bleeding I had good pedal feel.
Great I thought, I got lucky and it was only the master. Drive it around for a bit and get on the highway and just as I was about to downshift the pedal went flat to the floor again.
Well after pumping the pedal until it had good feel again I got it home and bleed it a couple more times just to make sure I got all the air out. Drove it again. Same thing, after a little while the pedal gets soft again.
Now before I go and replace the slave is it possible I have a faulty master? Having issues after replacing the master?
View 3 Replies
I keep finding air every time i bleed my clutch. I am not losing fluid but i can not figure out whats causing my problems. The pedal is soft at first and then gets harder and it sometimes needs pumped before i change gears or to even get into gear. I am afraid its the slave but i also just may have air in the system.
View 8 Replies
20th with 120,000 miles. Ok here's my problem, get in my car in the morning after a coldish night, (around freezing) clutch pedal goes almost to the floor with no resistance, i pump it a say 5 or 6 times and it gets stiffer but not 100% i drive it for 10 or 15 min and it warms up and the clutch gets back to normal stiffness. I'm thinking its the master or slave cylinder going bad or maybe it just needs to be bled and before i go and buy both of them and replace them, just wanted some opinions. Also its not leaking fluid at all and the reservoir is full.
View 2 Replies
A 2003 20th GTI (1104). It has the 1.8T engine. Car has appx 75k miles on it, timing belt has not been done yet.
My concern is here: I checked it out the other day, and while it was running I heard a soft whirring sound coming from the engine. So I popped the hood and I couldn't really put my finger on what it could've been. I liked the car aside from that, and would like to get it, but I don't want a car with problems.
View 5 Replies
I have an Imola 20th and recently i have been having some problems with my clutch. The pedal goes from being soft to very hard when its close to disengaging. It also engages very heavily when I go to let it out. This only started happening recently when temperatures started to drop if this has any effect on a clutch. Also, I replaced a shift fork two months ago and was curious if there was possibly anything going on with seals around the slave cylinder.
View 2 Replies
I took my car in for a clutch install, everything was fine except the clutch slipping. I go to pick up my car and once the car warmed up it started bucking / limp mode while accelerating. Take it back to the mechanic and he thinks he didn't reset the throttle body. So he says that should be it and I pull away. Same thing. Leave it with him again and he replaces with "diag" coils and new plugs. Leave again, same thing. He tells me to get totally new coils and try that. I am thinking its a missed ground cable or messed up ECU or something. During all this not one code it thrown.
20th GTI 1.8T 6 speed, stock clutch, all stock
View 14 Replies
I'm to the point of driving the car off a cliff! I've included a log of the car acting upt. The car is a 20th AE GTI AWP. It was chipped all it's life and ran like a champ. In November I installed a Frankenturbo F21T turbo kit, Bosch EV14 550cc injectors, 3" MAF, eBay FMIC, 3" catted exhaust, and a custom tune from Motoza. Dave at Motoza has updated the file 4 times and no matter what he changes, the car will boost up to the requested boost of 19psi and hold it for almost one second, then boost will drop to 12-15psi and then boost past the request to like 22-24 psi and go back and forth until the gear is over and I shift. Then it does the same thing in the next gear. i just want a solid 18-20psi without a manual boost controller! Things I have tried:
-Changed the N75J back to a NEW stock N75
-Replaced all the N75 vacuum lines
-Wastegate cracks at 7-8psi
-Replaced every worm feed clamp to a nice T-bolt clamp
-Boost leak tested to 18psi and found no leaks
-Deleted SAI, N249, and N112
-Unplugged MAF, nothing changed
LOG with multiple WOT pulls: [URL]...
View 17 Replies
I have a 20th 1.8t. It was running fine last week but all of the sudden i was only getting about 4-5 psi. I have check all over vwvortex for somewhat of an answer. I have no C.E.L.. I have checked for vacuum leaks with nothing coming up. I tried to check for boost leaks but it comes out of the dipstick hole. I have undone and re-installed the pancake pipe. The DV is holding pressure.
View 1 Replies
Earlier I was driving and some reason I just wanted to rev my car up. So I did and all of a sudden my car cuts off at around 5000 rpms.
View 5 Replies
when the traction control is off my boost hits 18psi and there have been times where it was 20 psi. My friend said i probably have stage 1 software .
View 4 Replies
Start with the basics, no CEL's, car has not cut out while driving and I've only had to attempt cranking up the car twice since I started noticing these issues about 6 months ago.
Symptoms: hesitation/variation in boost during acceleration- doesn't matter if I really get into the gas or just "normal" passing acceleration RPM's steadily climb, but just not as consistent or quickly. Also, the one that really has me really confused. With a 1/4 tank of gas or less, going up a slight incline (overpass); 70-mph-ish... acceleration dies off, rpm's slowly decline, and gas pedal doesn't respond for about 2-3 seconds. Car never shuts off, no CEL's, then everything is fine again! Even does it when I'm using cruise control. Car just rolled 110,000 miles
View 7 Replies
