Getting a slight FW chatter on stock clutch setup (02M)? I've noticed it for a while...most of the time I don't notice it, but other times I will be sitting in the drive-through and it will chatter. Goes away when the clutch is depressed.
View 17 RepliesI have an 04 Gli with 85000 miles on it. I just had the clutch done with a conversion from a dual mass to a single. When the car is idling there is some chatter coming from the tranny but it stops once i press the clutch.
View 3 RepliesI was driving down the street and i noticed i couldnt get it in first gear, almost like a wall blocking it. and then i put it into 2nd gear and i started rolling... i turned my car off and when i started it back up, it had a slight grinding noise (in neutral). i put it in first gear, took out the clutch and i wasnt going anywhere... same with 2nd gear...
so i towed my car to the shop, they said my clutch went out and i "lost first and REVERSE gear".... is that possible?!
I have 3.8k miles on my GTI, and recently started noticing this clutch chatter when my car is at a stop in neutral with the clutch engaged (pedal out). It goes away when the clutch is disengaged (pedal in). I'm not sure if the noise has always been there or not, but now that I hear it, it's really bothering me.
It doesn't affect driveability, and seems to disappear once the car gets moving. And it's usually not too bad, BUT sometimes the clutch engages in such a way that I get the rattle like in the second video. This is really the noise that makes me nervous. Does this sound like typical clutch chatter or do I possibly have a bad DMF and/or throw out bearing?
Car was taken to dealer today 3/7/14 and a new throw out bearing was ordered. I inquired about the possibility of it being a flywheel issue, and was told they wouldn't know that until they get into the transmission. So for now, car is schedule to have the throw out bearing replaced under warranty next week.
One day i was driving my pedal went flat to the floor ,then i noticed my brake fluid was low so then i tried adding more fluid and bleeding it n pumping the clutch i got pressure back, but now i hear chatter in the tranny and it wasn't doing that till after I bleed it. It will go into gear with the car off but as soon as the car starts in wont at all.
View 12 RepliesWhen pulling away casually in 1st from a stop, I hear a slight chatter noise. Had this since before the tune (stage 1). Almost like the sound a diesel makes at idle but only lasts a second or two. To the best of my knowledge it is an OEM clutch. Had 9k miles when I bought it, now has 25k.
View 24 RepliesI heard that smlw flywheel on the 6 speed trannys make a lot of chatter noise, I was cool with that so I put one in with a satch clutch kit and now it sounds like a marble or something is banging around inside!!!
View 3 RepliesI wanted to get a blow-off valve for my GLI but its bone stock, i was wondering if its possible or if it would cause problems. and if i can whats a good brand?
View 17 RepliesSo I have been looking but cant really seem to find an efficiant way to remove my stock shifter.
View 1 RepliesSo, yesterday I had my GLI in the shop to put a new timing belt on as well as some ECS Lightweight Pulleys. When I went to pick up the car, they did not install the pulleys. The reason they said was because the stock crank pulley has a dampener which keep vibration and balanced weight on the crank assembly and that the lightweight crank does not have these benefits.
So, now I have a set red anodized pulleys.. [URL].............
I find that the Rubber stock ones are not grippy enough. I have used the turner motorsport ones on my bmw but not sure if they will retro-fit on my 337.
View 2 RepliesI have a 20th with 106k on it and I notice mostly my right front rubbing on hard turns. Suspension is totally stock other than a 28mm rear sway. Is it possible that's causing it or is my suspension just getting old? No spacer on the fronts.
View 9 RepliesI recently got the GTI 1.8L 337 with 64,000 on it. It had been sitting, with daily start-ups, for about 8 months until the ALT was replaced. I've been driving it for a month with no problems until last week. At first I noticed the clutch pedal would pause on the way up for a split second then tap the bottom of my shoe. I thought maybe it needed adjustment but nothing serious. A few days ago the pedal would stick at 3/4 of the way up, and stay there most of the time unless I raised it with my foot, till the car warmed up a bit. Yesterday and today the pedal started to stick 1/4 of the way up, unless raised with my foot, at the morning start-up and will only come up 3/4 when warm. It also wont go into reverse at initial start-up until it gets really warmed up, shifting into other gears is fine. I've had no problems or real sounds shifting into any other gears, though out of 1st has been a little jumpy.
View 3 RepliesToday I went to start my car and let it warm up and everything worked fine and it started regularly but when I went to go drive the car and put the clutch in the pedal didn't return and I could not put it into gear, need to identify the problem.
View 4 RepliesMy wife was driving home and was exiting the freeway, downshifted and then no response from the clutch or gearbox. It would move left to right but not go into any gear with the car on. No real pressure in the clutch pedal either. With the car off you are able to find all the gears but when you start the car in gear with the clutch down it just jumps forward and dies. No smoke or burning smells either way and the pedal does come up by itself. Pushed the car into the driveway and its goin to the shop tomorrow morning.
With the search button so far: master/ slave cylinder, full clutch problem, air in brake/clutch lines, shifter linkage bracket
I don't think it's the slave cylinder as the pedal is NOT stuck to the floor, but I am not handy with cars, only motorcycles. First thing I checked was the linkage bracket, which seemed to be fine and as I stated, I was able to get in gear while car was off. Brake fluid was almost full but i know that doesnt rule out air in the lines.
We were headed home the clutch pedal went soft... Ok, I thought it's either the clutch master or slave. I get it home and replace the master and after bleeding I had good pedal feel.
Great I thought, I got lucky and it was only the master. Drive it around for a bit and get on the highway and just as I was about to downshift the pedal went flat to the floor again.
Well after pumping the pedal until it had good feel again I got it home and bleed it a couple more times just to make sure I got all the air out. Drove it again. Same thing, after a little while the pedal gets soft again.
Now before I go and replace the slave is it possible I have a faulty master? Having issues after replacing the master?
So I am pretty sure its my clutch that is the problem, here's what happens: When I go into second gear, it doesn't really grind.. but its tough to get it into gear and its only with second gear. sometimes it will go right in and others i have to double clutch. when i double clutch it goes in smooth every time. now I don't think it would be syncros because I am pretty sure if it was that it would do it every time I shift? It only does it while its cold or hasn't been drove in awhile.. but after i drive it around its fine so I am pretty sure its the clutch. Second thing, what is an upgraded clutch that is good for these 6 speed transmissions?
View 2 RepliesNoticed recently that my clutch is starting to slip. It only seems to happen when I'm cruising in 6th and floor it. When the boost spikes, the revs will shoot up ~750 rpm and then settle back down before the car starts to pull. It is chipped Unitronic Stage 2 with some other bolt-ons.
What I'm wondering is, should I just drive it like this until it really starts to go, or should I replace it now? And what are my options for a new clutch? I don't want to big turbo this car, so the most it could get is a few more bolt-ons. I'd like a stock feeling clutch.
I just put a stage 1 clutch in my 20th anniversary. When i was taking the transmission out, i dropped the hydraulic clutch line and all of the fluid spilled out. I got the whole thing done, and bled the clutch line and topped off the reservoir. I started the car and the clutch pedal had, what felt like the right amount of pressure. More than the stock, but not significantly. When i went to put it in gear, its like there is no clutch, just grinding and it doesn't go in to anywhere. I can cycle through the gears with the car off and like i said, the clutch has the right pressure and everything.
View 10 RepliesI have a 2002 1.8 Turbo VW GTI. Lately I've noticed that the car would hesitate slightly when slowing down. It would go up to at least 5000 RPM's or higher before it shifted over. The hesitation when slowing down and accelerating tend to happen when I drive. What to do, I went to the vw company they said if i want to change the transmission would cost me ~6k$ and f*ck me twice if if am paying 6k on a 2002 car.
View 3 RepliesNoticed the other day my clutch pedal trim is coming off... What did you do to fix it?
View 8 Replies