GTI 337/20th Anniversary :: Inner CV Joint Boot Cover Won't Come Off
Sep 23, 2011
Trying to do new boot kit on inner cv joint. I have the ball and cage type inner joint. The joint cap comes off really easy (and a new one comes in the boot kit). The boot cover doesn't come off so easy (and there is no replacement in the boot kit). Bentley's and pretty much every other source of info says to carefully drive off the boot cover to remove cage. But they all pretty much gloss over how to do this carefully. I've hit it a couple of times with a screwdriver blade and hammer, but it's not budging. Trying not to hit it too hard.
View 6 Replies
Advertisement
I just pulled my axles, cleaned and regreased the cv's, and replaced all the torn boots with better ones. Now it seems as though the joints make noise when they didn't before. It's kind of a metal scraping sound, at low speed over sudden bumps, when the wheels are turned.
View 1 Replies
So the long story short, i bought a JB 20th with 36k miles on it, lowered on Neuspeed Race Springs and HD Koni Struts. When bought, both inner CV boots were torn on the car. I ordered OEM CV boot repair kits for all four joints (made by Rein OEM manufacturer) and rebuild the axles completely.
I got the car up in the air today and the drivers side inner CV boot is already torn, after only a few hundred miles (if that many).
From what i understand, it is a common problem on the O2M 1.8T setups after lowering? Is there a solution?
I searched around, but it is still not clear what is the source of it, even though i found plenty of threads that state that its a common problem.
Upon inspection, the geometry of the axle or the angle at which it operates when the car is on the ground does not look that bad, it simply does not make sense.
View 17 Replies
I know this has been covered before and I did search but got no where. It's covered in the FAQ sticky but the link is no good. Where can I get an axle assembly that's not going to cost me 550 bones like on ECS?
View 14 Replies
Just tore through my second driver side outer boot it's frustrating. I'm thinking about buying an axle but are the boots not going to rip on them. Thing is I don't really get why the are ripping since I'm not super low or anything I know people that are lower and haven't had any issues
I put this new OEM axle in just a couple months ago. Could my Coilover be sitting to low in the strut housing and rubbing on the boot or what. I don't know if that is the mechanical terms but I did my best but how would I go about fixing this.
When I was looking around for the axle last time and I tried to go through smaller shops but none of the axles they had matched up, so I had to go to the dealership and my wallet took a beating. This time thinking about the cv boot kit for urotuning.
View 14 Replies
I have a 2002 337. My gear selector has broke down under the boot.
Can I replace this part? Where can I get one? How do I get the old one out?
View 1 Replies
My Question is, I have a 20th and I was wondering how to unclip the ring that's at the base of the shifter to get to the shift knob and boot. I'm sure its really easy but, I've been messing around with it and it seems pretty solid. I just don't want to break any tabs or anything. Is there a trick to getting this off without breaking the clips on the ring?
My 2 question is, How easy is it to swap out the shift boot? Will a universal shift boot with the elastic bottom work? I'm just wondering cause I have a momo setup that I'd like to swap over.
View 5 Replies
Can't manage to get it back on. Who knows the trick?
View 4 Replies
My GTI has a problem i don't know how to fix. Shift knob on the automatic mk4 (2005) GTI, has a rubber piece that covers the ther gears when you are in the one of your choices. Such as if you were to be in drive then park reverse and neutral would be covered by the rubber sheet, as would the gears under drives such as the 4th 3rd and 2nd gears. That sheet of rubber on the car has been unattached from the front side of the sifter so that there is a hole in front of the shifter if I were in drive, the rubber piece that covers that hole was jammed into the front part of the gearbox (directly under the shift knob when in park).
I managed to get the rubber piece out from under there with a pair of very fine pliers. now my problem is how to attach the sheet back to the front of the shift knob. the rubber sheet seems to be very loose and when it is moved side to side you can see that there is some sort of zipper pattern along each edge of the rubber cover. MY QUESTION IS!! how to reattach the rubber cover?? or do i have to take that section apart and replace it?
View 1 Replies
I have a 2004 1.8T 4Motion (automatic) that blew a CV joint boot. After inspection of the other side, I decided to replace both (just the outer boots). Got the axles out without much trouble but now I cannot drive the joints from the axles. I've tried both and neither is cooperating, I've knocked out off them with a mallet but they aren't budging. Is there something to do besides just driving them off?
Axles are tubes (hollow) p/n's 8D0 407 271 (& 272) ED.
View 10 Replies
How hard to replace it? I found a minor leak from left crimp clamp, the grease leaks all around it. It looks not too bad, but the grease will leak all out later. I thought there is repair kit on ECS, It seems I can replace brake pad,rotor and cv boots joint in the same day.
View 17 Replies
I believe that I have a leaking CV joint boot in my 2006 Outback. Occasionally smell something burning. Lifted hood and had some smoke. Saw leak and a friend stuck a finger into a hole in the boot.
View 9 Replies
I'm repainting my peeling shifter trim plate and replacing the shift boot with a new one. Lots of support available on removing the shifter and disassembling the trim plate, but no clear instructions on how to remove the boot from the knob. It looks like this inside:
How do I separate the boot from the knob to install a new boot? The only instructions I found showed a metal collar which is not the case in our cars.
View 1 Replies
I want a 20th AE & have seen pics that say ESP on a button next to the hazard & others say ASR. I know that their was one option for the car: ESP. So what's ASR? Is one better than the other? Is it the same? I've heard that the ESP sucks for autocross. Is this true?
View 8 Replies
I was driving at about 60mph in 4th gear and knocked it into 2nd and the rpm's hit the max and the car shut off and I have not been able to get it started. I have compression, fuel, and spark . I've checked oil and don't have any coolant in and nor did I have any oil in my coolant. When I try to start it it try's to start but won't turn over so .
View 12 Replies
Driving home from work, I was about 5 minutes from home, got to a light only to not be able to go into 1st. I popped it into 2nd and drove home like that pretty much. Car will let me get into reverse and all other gears.
I can put the shifter towards first but it doesn't fully go in and when I gave it gas it would let me start to creep and then grind a little and pop out.
Heres a pic for your click .....
View 24 Replies
I was searching but I can't find any DYI's on turning your Daytime Running Lights off on our cars. I don't feel like buying a euro switch right now. How to do this or has done this to their vw's?
View 24 Replies
I was following the directions on the APR site to remove the ECU and it seems to not make sense. Saying the ECU is on the passenger side underneath the molding....
is the ECU in the center?
View 1 Replies
I've had the leak for a long time now possibly from when I've gotten it... anyway when I first bought it I drove it a lot, like 8k miles in 6 months. During that time I went through a qt of oil about every week and a half. Now the last 3 months I've been barely driving it due to life changes so I'm barely putting oil in I'll go weeks sometimes of checking the level and it'll be fine. This leak has to relate with how often its driven and maybe hot?
I've had the car up multiple times to try and find the spot all I know is it's behind the engine below the valve cover gasket and above or near the turbo area(I've only owned my first VW this 20th for less then a yr so I'm still learning)
View 8 Replies
I get up to go to work today and the car runs fine, a few hours later i get back in, try to put it in reverse, and nothing.. it wont let me shift in after i push it down. So i push it back in neutral and drive away.. every gear works fine, when i got home i took off the boot, tried to see if anything was loose, shake it a few times and out of nowhere first and second give. They were working perfectly 5 min before, and now they just feel really loose, but every other gear works fine, so now I have no reverse, 1st or 2nd. Did I just knock something out of alignment or is the problem a lot worse.
View 3 Replies
I recently took out my headliner And my passenger's side seat. When I put everything back together, I turned the car on and the light came on. What can be the issue?
View 10 Replies
