GTI 337/20th Anniversary :: Front End Rocks And Bucks When Shifting?
Apr 11, 2010
I just had new R32 rear lower control arm bushing installed but I still notice that the car rocks and bucks somewhat when I shift. I can control it I shift and accelerate slowly and deliberately but where's the fun in that?
I didn't replace the front lower control arm bushings but I'm starting to think I should have. Or maybe something else needs replacing??
Experiencing this bucking when shift? Maybe I just suck at shifting?
View 11 Replies
Advertisement
If the car is moving, the transmission feels like it doesn't want to let you shift into first (even with the clutch all the way in) until you've slowed down considerably. it grinds if the clutch is all the way in and i try to put it into 1st at about 30 mph, for example.
I always thought that it was probably a safety feature so you don't try to get into such a steep gear at that speed. i guess I'm just trying to make sure of that, because I've never researched it before. What I'm starting to notice now (or maybe its in my head) is that the trans is being real particular about me having the clutch pushed in all the way _to the floor_, something that it something that it tends to give me a bit more slack with the other gears.
For example shifting 2nd to 3rd, i can usually have the clutch pedal about an inch off the floor and it will still shift. is this a sign of clutch wear? it's got over 100K miles on it of mostly granny shifting.
View 8 Replies
Trying to find if any updates to this problem. Just broke a second fork yesterday- only issue I've seen is to simply replace with the same brass fork.
View 10 Replies
was diriving my toy1and was shifting from 3rd to 4th when the rpm reved up and the car would not take any gears to drive foword or revers my gears when you shift are engagging but no mvement also i dont have to push the clutch in to shift it will go with out clutching.
View 9 Replies
First off i couldn't get the car into reverse to back out of a convenience store and then i let off the clutch to try and pump it again and the car just dies. drove just fine up until i parked. Now when i try to move through gears it sounds like it's shifting but the car doesn't move. The car does have a stronger clutch and unitronic chip if that would have to do with anything.
View 13 Replies
Quick q recently just got a gli and I've noticed a knocking sound when accelerating and shifting from stops could this be my motor mounts ? I was thinking my tranny or clutch but everything runs smooth and goes into gear fine
View 5 Replies
sometimes when i switch from 1st to 2nd or 2nd to 3rd i get a loud popping noise like my exhaust is hitting the under side of the center column. I have had the car on a lift and shook the hell out of the exhaust...it's not moving enough to cause that loud popping...so i figured it could possibly be the dogbone mount gone and the downpipe is hitting when i shift because the mount is bad?
Or could it be one of the other mounts...I'm going through a divorce right now and really really broke so i need to make sure i get the right one and fix it right the first time. What mount it is if not positive its the dogbone?
View 4 Replies
2002 GTi 337 not shifting out of 1st until is warmed up for 20 min. Then shifts fine. I've already attempted to add the "liquid gold" G-052-990-A2 ATF fluid from VW at $35qt. I put in about 200ML to no change, then another 200ML to no change. So from reading other posts in VWvortex I've seen many folks with the Jetta have had very similar symptoms. They are installing a new (Solenoid valve N92 (green) to fix this issue. Many of them are even using over the counter synthetic ATF. Before I dig in, just wanted to know what folks with the GTi 337 think about this? Am I dealing with basically the same transmission?
View 2 Replies
well what are the chances that all in one week.. I would get my front end hit in the same spot that i just fixed.
get a crack in my windshield.
get a flat tire.
Have the tab that holds the passenger sun visor in place break off.
Have a new "clunking" noise in the front end.
View 9 Replies
I got a question..how do u remove the front gli valance?
View 4 Replies
Went to lower my front end today and after trying for 15 min the nut directly under the spring was frozen. i sprayed it with PB blaster let it sit for like 20 min, kept on spraying it during that time. tried adter that and still did not budge a mm. even tried with a flat head and a hammer trying loosen it. did not work. was wondering if there was any other way i can get it loose?
View 8 Replies
Both the front headlights do not turn on. I checked the fuses on the side panel and they all seem fine. I removed my battery to start another car. Do not know if that is the cause for killing the front head lights. Day time running lights are not on either. Lower fog lights work.
View 8 Replies
Couple of days ago I notice some rubbing on my front passenger side and I'm pretty sure it's my sway that rubs on the axle. I could understand that if I was slammed but I'm not even all the way down on my vmaxxs. I have about 15 threads left and it still rubs especially while making left turns. When I first got my coilovers I used to drive all the way down with no issues but now it's getting worse and worse and I don't know what to do besides going up couple of threads. The tricky part is that my driver's side front doesn't rub at all. Any ides why would start rubbing all of the sudden when it never rubbed before even when I was lower? Is there anything I could do, maybe adjust the end links or something? I know I can cut the sway out but but I'm pretty sure there is another way to fix it since it started rubbing recently.
View 13 Replies
Ok, Im trying to get my front licence plate holder off. I've looked in all the DIY forums and cant find what im looking for. My question is how do i get this thing off?? I've took the two screws that hold the thing to the bumper off, and its still soild as before i took the screws out. Is it held on by the rub strip?
View 24 Replies
I am wondering what size spacers i should run in the front and back?
I am going to be on the stock aristos for a bit but would like some poke, fill the fender or maybe even come out a little bit further.
View 10 Replies
I just picked up a BMP 20th ann last weekend after looking for a nice clean one for a while. I love the way the car looks compared to my stock 1.8t gti, and I am also loving the Recaro seats. The 20th is all stock, and i have a few minor things in mind for it just to get the car to look how i want. I also had a few questions... do tires rub against the front when turning sharply? The car has stock suspension... also the front lip has a small crack and i was wondering if it was worth it to get it fixed or to buy a new one? And there is an annoying squeaking sound coming from the steering column area...
[URL]...
View 19 Replies
Noticed the other day when I was backing my GLI out of the garage a clunking or popping noise that sounds like it's coming from the drivers side. It only doesn't it once and only when I am backing out and turning at the same time like out of my garage or parking spot at work. My car has roughly 54 thousand miles on it and still the original suspension.
View 10 Replies
Pulling into work today and backing into my parking spot, a fellow employee noticed something odd about my front wheels, so he hopped in my car so I could see the issue.
From a dead stop accelerating forward, the front wheels shift a few inches to the rear, and same thing when backing up from a dead stop they shift to the front. Both sides are doing this evenly. I haven't thrown it on the lift yet but I was thinking a possibly bad dogbone mount. The car has 133K on it and the bone has never been touched.
View 4 Replies
I got 66,000 miles and I am getting a rattle/popping noise when driving on roads that are bumpy. I thought it might be a strut going bad but somebody told me it might be a Lower control arm rear bushing....
View 2 Replies
After euro switch is installed on mk4 gli, the parking lights still remain on with the front fogs.The switch would be in the middle position. So the DRL's are off and just the parking lights are on until the switch is pulled out into position 1. Then the fogs come on and pulling out into position 2, turns the rear fogs on.
View 3 Replies
Having trouble with front brake pads rattling? About a month ago, I replaced pads - rotors - caliper pins on my 20th GLI. I know these cars ride a bit stiff but it sounds like my front end is about to fall off. All brake parts were torqued to spec - I've gone through all T25/T30 torx front end screws etc and I just can't find the rattle??? This has only started within the last few days. Any other places to check for obvious loose bolts etc?
View 15 Replies
