Changing the oil in my friends gli tonight and the drain plug ended up becoming stuck in the oil pan hole, just spinning in both directions and not tightening or loosening. He has the hybrid oil pan, and we took the bottom steel part off, do they sell just that part so I could fix the stripped drain hole, or should I try and salvage the one I have now and rethread the hole with a bigger drain plug?
View 1 RepliesI can't see where it's coming from but it's leaking onto my TIP. it's not a lot though.
View 4 RepliesHappened first yesterday. The rpm and speed gauges get stuck at the 10 o'clock position. Seems all the lights come on. I can accelerate for a bit but the car just putts and then turns off. After that i try to start the car and nothing. If i take the ground of the battery for 10 min (ecu reset?) the car starts right up but any sooner and it wont start. I have APR stage 1 flash, cat back exhaust, drop in filter, forge hybrid valve, and Boost gauge.
View 4 RepliesWeirdest thing happened this morning. I went to start the car and the horn was immediately on. I figured maybe the steering wheel was stuck. Anyways it went for a bit then while I was on the highway it came on and stayed on. People were looking while I'm going 60mph with the horn blasting. Anyways it went off on its own. I checked the fuse today and it is blown. I no longer have a horn. Why this happened? I will take the steering wheel off tomorrow to check the grounds.
View 4 RepliesI parked the car yesterday and everything was working fine. I go out this morning to go to work and i cannot get the car to go into reverse. I put it in neutral and attempted to push it out of my parking spot, but when I took my foot off the clutch, it stalled like it was still in gear even though the stick was in the neutral position. While still in the neutral position, i can still move forward as if it were in first. When i put it in reverse and attempt to move, i get no movement. I can get it to move forward, but it refuses to go into reverse. I have no diagnostic lights illuminated and the car has no issues running or starting.
View 14 Replies50k Miles on my clutch. Was driving a couple weeks ago on the highway and clutch stuck to the floor. At first I thought it was my Slave cylinder. Got the trans out this weekend to find the mess (below) inside my bell housing. Obviously need a new clutch now and will still replace the slave while I am in there.
Cars setup is around 375ish whp. I know I could spend 1300 bucks and call it a day for a clutch master or south bend but was seeing if there is a cheaper alternative.
Also If I were to buy an OEM clutch or an upgraded one that was not rated for up to 400~whp would it drive and pull the same as a fully upgraded one just not last as long?
6 Speed ...
So last night I was driving home from work, and at a red light while i was waiting to go i had my clutch down when light turned green i tried to go and noticed i could not put it in gear and that my clutch pedal was stuck in place. i didn't know what to do so I checked my shifter plate everything looked fine so went to look at the pedal and i pulled it forward and it came lose. I started it up everything was fine and back to order. This morning going to work same thing happened again, I don't know what is going on and what could be the cause?
View 5 RepliesWell, like the title says, The trans is stuck in third gear, with no other gears, or neutral or reverse. The car is slightly modified 02 GTI 337. APR Chip, Forge TIP, Full 3" exhaust, Greddy FMIC. I definitely drive the car, and had been beating up on it on the highway for a little on my way in to work, then on the way home, down shifted to pass someone, dropped it third, passed them, went to shift to fourth, Shifter moved, felt like it engaged "a gear" and then then i let off the clutch and it was still in third.
I also noticed that unless, I press the clutch in the, the car stays in this gear, even when the shifter is in neutral. I looked at the linkage, and it appears to be functioning. I did some reading around the Vortex and it seems like this might be a shift fork problem. Also, if the trans will be apart, what items should be upgraded?
Yeah it was stuck in the "up" position, just running forever. Turn the car off and just keep running. So I took it apart and un-plugged it.
I plan on swapping it for the drivers and see if it follows the mirror motor. Yeah, I been getting dead battery and this is why.
Happened on my mk6 now on the 20th! When I go to hit the switch for the gas tank release it is completely silent. Could that be the module? Half a tank left so not to worried about bringing it somewhere.
View 2 RepliesI just got a Walker SoundFX muffler and there is no drain hole for condensation. Should I make one?
View 3 Replies2000 honda accord automatic, 4 cylinder. As I unscrew the drain plug of the transmission, i stripped about 2/3 of the hole threads. the bolt threads are OK. what are my choices to fix it? i do not believe there is room to "tap and die" (?). I visited locan NAPA and they suggested me using 2 liquid epoxy. what i am thinking to do first is to use the liquid gasket surrounding my bolt, bolt them in using the remaining 1/3 of the hole thread. Let is sit and cured. it will work?
View 8 RepliesI have a 91 corolla 1.6 5 speed. There is oil in one of the spark plugs and its covering the entire bottom of the spark plug, which is also making the car sputter as it runs. I'm told the seals are bad? If so, what kind of seal is this? Where is it located inside the engine exactly? If not, what else could it be?
View 3 RepliesOkay so I was getting the misfire in cylinder 3 so I pulled the plug out and it had coolant in it. Does that mean it needs a new intake manifold gasket? That is what the guy told me at the parts store. Also can I drive it like this or will it damage the engine?
View 1 RepliesHaving issues with transmission fluid spewing out the dipstick hole? Truck is an 04 Escape and has worked great until I had a rear manifold leaking. I took the truck to our mechanic and he replaced the rear manifold cat converter. He broke 3 of the 4 bolts so he told me he had to roll the engine forward to gain access to tap out the broken bolts. Im sure he took the throttle body and intake off for more room. I Got the truck back and noticed transmission fluid all over my driveway the next day. I contacted the mechanic and he states it was nothing he did and cannot figure why this is happening. Basically told me to fly a kite!
View 14 RepliesSo I have the oil filter out and can't get the drain plug off the pan. I tried the 034motorsports dogbone insert but I couldn't get that bolt loose either. Mainly looking for tips on the drain plug. Even when I put extra leverage on the ratchet if won't budge.
View 7 RepliesI had my 10k service done at the dealership earlier this year, currently at 16.5K miles. My GTI was parked at my parents' garage for a week while I was away for travel. When I returned and went to move my car, I noticed a puddle of oil under the GTI. Since it was a sunday, there were no dealership service departments open, so I went to a quick change oil place and they told me that there is a leak at the drain plug. The tech noticed the oil was low, drained the oil and replaced the drain plug, and when they filled the oil, it immediately started leaking at the drain plug. They added teflon tape to temporarily work with the leak. I will be scheduling a service appointment at the dealer I had my 10k service done.
Have a MK6 and experienced a leak at the drain plug? Could this leak be due to the dealership service tech over tightening the drain plug at my 10k service? The quick oil change place did note that I came in with a leak from the drain plug, in case the dealership tries to blame the oil change place for the leak.
2001 Ford F350 V10, 220K in crap condition
First of all on the left side 2 of the coils were so withered the rubber separated from the bolt and were loose. Without any tools I was able to remove 2 coils. Typically there is the hole and several inches inside hole is where the spark plug sits.
On cylinder 4 the spark plug is on a funny angle and is level with the hole or possibly poking up above the hole. Tried sticking the ignition coil over the spark plug but it wasn't correct. Leaving it alone until my cousin can take a look. Spark plug was tight but I didn't put a ratchet on it.
Wondering, is this the infamous spark plug blew threw the cylinder thing. Wish I would have taken a picture (I will next time I'm with truck).
Had codes for misfires on 4 cylinders but that was with 2 coils unplugged (way I got truck at auction)....I replaced 3 of them (1/2/6).Cleared codes...4th cylinder remained unplugged....And the only code I got after letting truck idle for 10 minutes was something about ignition coil D (which would line up with cylinder 4 I think).
Doing the oil change today and I'd like to know where the oil drain plug is. I have the skid plate off but I'm not 100% sure on the plug location.
View 1 RepliesI have around 127 miles on my car and was using it as a daily for sometime for work. Due to this, oil changes were done by Kauffman Tire, work paid. Now that I am in a different role my car is not my daily any longer and I tired to change my own oil. My oil filter cap drain plug is hollowed out! I couldn't get it out at all with the 6mm Allen. I thought I would be able to take the filter off from the inside. I soon found out I can't do that. Am I stuck buying a new filter cap and plug from the dealer? Any way to get the filter off without the drain plug?
View 9 RepliesWhat are the correct torque settings for oil drain plug, oil filter and spark plugs on a 2.0 FSI engine?
View 3 Replies