GTI 337/20th Anniversary :: Clutch Pedal Went Soft?
Mar 24, 2011
We were headed home the clutch pedal went soft... Ok, I thought it's either the clutch master or slave. I get it home and replace the master and after bleeding I had good pedal feel.
Great I thought, I got lucky and it was only the master. Drive it around for a bit and get on the highway and just as I was about to downshift the pedal went flat to the floor again.
Well after pumping the pedal until it had good feel again I got it home and bleed it a couple more times just to make sure I got all the air out. Drove it again. Same thing, after a little while the pedal gets soft again.
Now before I go and replace the slave is it possible I have a faulty master? Having issues after replacing the master?
View 3 Replies
Advertisement
I keep finding air every time i bleed my clutch. I am not losing fluid but i can not figure out whats causing my problems. The pedal is soft at first and then gets harder and it sometimes needs pumped before i change gears or to even get into gear. I am afraid its the slave but i also just may have air in the system.
View 8 Replies
I have an Imola 20th and recently i have been having some problems with my clutch. The pedal goes from being soft to very hard when its close to disengaging. It also engages very heavily when I go to let it out. This only started happening recently when temperatures started to drop if this has any effect on a clutch. Also, I replaced a shift fork two months ago and was curious if there was possibly anything going on with seals around the slave cylinder.
View 2 Replies
20th with 120,000 miles. Ok here's my problem, get in my car in the morning after a coldish night, (around freezing) clutch pedal goes almost to the floor with no resistance, i pump it a say 5 or 6 times and it gets stiffer but not 100% i drive it for 10 or 15 min and it warms up and the clutch gets back to normal stiffness. I'm thinking its the master or slave cylinder going bad or maybe it just needs to be bled and before i go and buy both of them and replace them, just wanted some opinions. Also its not leaking fluid at all and the reservoir is full.
View 2 Replies
I recently got the GTI 1.8L 337 with 64,000 on it. It had been sitting, with daily start-ups, for about 8 months until the ALT was replaced. I've been driving it for a month with no problems until last week. At first I noticed the clutch pedal would pause on the way up for a split second then tap the bottom of my shoe. I thought maybe it needed adjustment but nothing serious. A few days ago the pedal would stick at 3/4 of the way up, and stay there most of the time unless I raised it with my foot, till the car warmed up a bit. Yesterday and today the pedal started to stick 1/4 of the way up, unless raised with my foot, at the morning start-up and will only come up 3/4 when warm. It also wont go into reverse at initial start-up until it gets really warmed up, shifting into other gears is fine. I've had no problems or real sounds shifting into any other gears, though out of 1st has been a little jumpy.
View 3 Replies
Noticed the other day my clutch pedal trim is coming off... What did you do to fix it?
View 8 Replies
I just replaced my clutch and have put everything back together, and bled my clutch line, but I have absolutely no pressure still in my pedal. I read that u need to make sure your brake fluid reservoir is filled to the max, but following the clutch line, I dont see it going to the reservoir? I also read that the master cylinder is behind the clutch pedal, does the master cylinder hold any fluid that maybe I lost during the bleeding? I'm at a loss right now.
View 12 Replies
So last night I was driving home from work, and at a red light while i was waiting to go i had my clutch down when light turned green i tried to go and noticed i could not put it in gear and that my clutch pedal was stuck in place. i didn't know what to do so I checked my shifter plate everything looked fine so went to look at the pedal and i pulled it forward and it came lose. I started it up everything was fine and back to order. This morning going to work same thing happened again, I don't know what is going on and what could be the cause?
View 5 Replies
Coming to a stop, clutch pedal just lost all pressure. I can bring it back up, but even the slightest touch will send it to the floor again. I get the brake warning light on the dash. What could be causing this?
View 7 Replies
My clutch has been feeling very strange lately, and has had a mind of its own. I have looked underneath myself, and have even taken it in to two transmission speacialists and they can't figure it out. The master cylinder isn't leaking, and the slave cylinder is fine as well.
Here's what is going on with my clutch...
- I will push in the pedal, and there will be ZERO resistance until about 1 inch from hitting the floor, then all the pressure is there, and I am able to shift. However, sometimes I won't even be able to put it into gear because the clutch won't engage.
- Then I will pump the pedal, and slowly I will gain a little more room on the draw of the clutch, and it will feel fine. All the way to the point where a few days later it will be driving like new.
- Then it will start feeling funky again a few days later and the cycle starts over.
I drive a 2003 GTI 20th AE.
View 6 Replies
The transmission is a Six-speed MQ350 transmission in an MKIV 337 GTI.
I was driving last week and ran over a large snow chunk, heard it hit the underside of my car. A mile down the road my foot is resting on the clutch pedal at a stop light, and the clutch slowly went to the floor. It was still drivable, barely. The clutch came about an inch off the floorboard, but still caught. So i pull into the parking lot ahead of me, and was barely able to move the shifter left to right nor would the shifter go into gear. There were no fluids coming from under the car, nor could i see anything that looked wrong. I turned off, back on again. nothing. I then pulled the clutch pedal up from the floor and it went back to normal. Everything seems normal now, but the shifter seemed a little sticky yesterday from left to right.
View 6 Replies
Recently my clutch started acting strange, the pedal felt softer and eventually after I pressed it in it stayed on the floor. After pumping it, everything went back to normal. Next day, still same thing, no pressure in the clutch pedal. I checked the brake fluid and it's full. There is also no sign of any leak. Took the car to the mechanic, he recommended changing the master cylinder. I changed it but still nothing. I tried bleeding the slave but every time I bleed it, it has air in it. So I'm stuck and don't know what should I do next. I think it might be my slave cylinder but I don't have a place or tools to do it myself. I'm pretty sure the entire tranny needs to be pulled out to remove the cylinder. I also read that most people change the clutch when they replace the slave.
View 10 Replies
So your clutch pedal operates properly, the clutch engages with no issues, but this annoying squeak, snap, crackle, and pop noise keeps coming from the clutch pedal within the cabin.
Could it be your clutch master cylinder? CMC is not leaking in the engine bay and the driver footwell. Not the CMC.
Could it be your clutch switch that's used to control revs and cruise control? Removed it and clutch pedal still made noises when pressing and releasing the pedal. Not the CS.
Could it be the over-center spring that sits behind the clutch pedal assembly? How could it be? It's just a spring. Springs that compress in that orientation don't make snap, crackle, and pop noises.
What most people fail to realize is the noise is coming from the pedal assembly, but it's not the pedal structure or the pedal. It's the pivot point where it mates with the clutch pedal mounting bracket. At the pivot point are two bushings (one on each side of the pedal structure) that wears out over time creating these noises.
Please look up the part number for these bushings. They look like the following at this link but these are aftermarket upgrades for BMW's.[URL] ....
View 4 Replies
Just as the title states. When I put the AC on in the car my clutch pedal gets some play in it, enough that it messes up shifting and gets jerky. I tried searching, but no results
View 14 Replies
I have had everything related to the clutch changed, and I even had a dealership bleed the clutch line. The problem is the clutch pedal is soft and will sometimes work good and sometimes won't. If I prop the pedal to the floor for a few hours, it works fine for the day. what gives?
View 1 Replies
Preliminary info:
APR 93 tune
Carbonio Intake
Silicone TIP
I picked up my 20th today and drove it 4 hours home. It has 74k on it, original timing belt. The timing belt kit is in the mail on its way here. Its the first thing I'm doing.
As I was driving it home on the autobahn doing about 150k/hr and I gave it half throttle to pass, I felt the turbo spool and I accelerated past the car. However, when I went to make the next pass, it felt like I had no power. I feathered the throttle a bit and it felt like my car was only getting maybe 3 PSI of boost. Very little actually. I do not have a boost gauge so I can't really say it accurately. As I was driving, i shut the ignition off and turned it back on. After that, I was able to get full pressure back.
View 6 Replies
A 2003 20th GTI (1104). It has the 1.8T engine. Car has appx 75k miles on it, timing belt has not been done yet.
My concern is here: I checked it out the other day, and while it was running I heard a soft whirring sound coming from the engine. So I popped the hood and I couldn't really put my finger on what it could've been. I liked the car aside from that, and would like to get it, but I don't want a car with problems.
View 5 Replies
Just the other day I got the clutch replaced on my 06 WRX. I took it to a reputable workshop that I've dealt with before. When I got it back the clutch pedal feels very soft and goes to the floor with ease, whereas before it was a lot harder and felt good. It works good and dosen't slip but just a soft pedal. I also went for the OEM replacement and not aftermarket. Some of the google searches I've read say the pedal will get harder after about 1000-2000 km.
View 5 Replies
We have a 1997 Mitsubishi Eclipse with a hydraulic clutch. The pedal is very soft in the morning and requires a good bit of pumping the pedal to get good pressure. I know the system needs to be bled. Does this mean one of the cylinders is bad? I have added a little bit of fluid over the last year- maybe 2 or 3 ounces total. Right now the fluid level seems fine but it still needs to be pumped before driving.
View 7 Replies
I changed my oem clutch in my mk4 golf 2.0l with a stage 1 ecs tuning clutch kit. Lightweight flywheel, clutch disk, pressure plate and throw out bearing. But since I have my clutch pedal has been less stiff then usual. I like my clutch pedal as stiff as possible but it just isn't I bled off the slave cylinder. When I was done no air was coming out but it is still way to soft for me. What should I do next??
View 6 Replies
Today I went to start my car and let it warm up and everything worked fine and it started regularly but when I went to go drive the car and put the clutch in the pedal didn't return and I could not put it into gear, need to identify the problem.
View 4 Replies
