GTI 337/20th Anniversary :: Clutch Grinding When Go Into Second Gear
Feb 7, 2010
So I am pretty sure its my clutch that is the problem, here's what happens: When I go into second gear, it doesn't really grind.. but its tough to get it into gear and its only with second gear. sometimes it will go right in and others i have to double clutch. when i double clutch it goes in smooth every time. now I don't think it would be syncros because I am pretty sure if it was that it would do it every time I shift? It only does it while its cold or hasn't been drove in awhile.. but after i drive it around its fine so I am pretty sure its the clutch. Second thing, what is an upgraded clutch that is good for these 6 speed transmissions?
View 2 Replies
Advertisement
I just put a stage 1 clutch in my 20th anniversary. When i was taking the transmission out, i dropped the hydraulic clutch line and all of the fluid spilled out. I got the whole thing done, and bled the clutch line and topped off the reservoir. I started the car and the clutch pedal had, what felt like the right amount of pressure. More than the stock, but not significantly. When i went to put it in gear, its like there is no clutch, just grinding and it doesn't go in to anywhere. I can cycle through the gears with the car off and like i said, the clutch has the right pressure and everything.
View 10 Replies
So I picked up a 20th today. The clutch has 30k on it its an oem luk. Drove fine most of the ride home then i went to shift and it wouldn't grab. Got it towed home. trans goes into all gears fine. When you put it in first and try to go it starts to roll but just makes a grinding type noise and doesnt go into gear. I didn't hear any chatter until maybe 10 miles before this happened. I still have pressure in the clutch pedal as well. when the car is in neutral running there isnt any noise which makes me think it isnt the throw out bearing.
View 2 Replies
Normally I'm pretty good about searching and finding info, but there doesn't seem to be a lot out there for these trannys. In any case, when I hopped in my 20th to move it today, I got this grinding noise when letting out the clutch. The car won't go move in reverse or any of the forward gears. Idles fine, sounds fine when in neutral or when the clutch is depressed. It just grinds when you let the clutch out. Seems like I can select each gear OK. Linkage feels normal.
View 2 Replies
I was driving down the street and i noticed i couldnt get it in first gear, almost like a wall blocking it. and then i put it into 2nd gear and i started rolling... i turned my car off and when i started it back up, it had a slight grinding noise (in neutral). i put it in first gear, took out the clutch and i wasnt going anywhere... same with 2nd gear...
so i towed my car to the shop, they said my clutch went out and i "lost first and REVERSE gear".... is that possible?!
View 9 Replies
Today I went to start my car and let it warm up and everything worked fine and it started regularly but when I went to go drive the car and put the clutch in the pedal didn't return and I could not put it into gear, need to identify the problem.
View 4 Replies
My wife was driving home and was exiting the freeway, downshifted and then no response from the clutch or gearbox. It would move left to right but not go into any gear with the car on. No real pressure in the clutch pedal either. With the car off you are able to find all the gears but when you start the car in gear with the clutch down it just jumps forward and dies. No smoke or burning smells either way and the pedal does come up by itself. Pushed the car into the driveway and its goin to the shop tomorrow morning.
With the search button so far: master/ slave cylinder, full clutch problem, air in brake/clutch lines, shifter linkage bracket
I don't think it's the slave cylinder as the pedal is NOT stuck to the floor, but I am not handy with cars, only motorcycles. First thing I checked was the linkage bracket, which seemed to be fine and as I stated, I was able to get in gear while car was off. Brake fluid was almost full but i know that doesnt rule out air in the lines.
View 3 Replies
so I bought my gli about a month ago assuming it needed a clutch (got it for a steal so wasn't worried about it) the kid I bought it from didn't really know much about the issue but it was a constant grinding when in gear and moving but the second you engage the clutch it would stop, and quiet down completely, so I dropped the trans and inspected clutch, throw out bearing, & fly wheel it all looked new.
So than my second guess was it was something internally in the transmission so I sent it out to be inspected and repaired as needed. I got a call from the shop today that said everything was perfect so I am completely stumped as to what my problem is. I have a new clutch, flywheel, throwout bearing, all new linkage, & am changing fluid. I don't know what else it could be and really don't wanna have to drop the trans again once its back together.
View 1 Replies
I recently was driving home from a buddy's house, when at the light i go to put the car in 1st gear and it was way harder than normal. I kept driving just to try and get home but it was so bad that i never went past 3rd gear.. I'm pretty sure the clutch went out, since it was extremely hard to get the clutch to engage to get it from gear to gear, and i basically have to turn the car off to get it to stop so.....
I'm pretty new too the vw game, and don't know of any good companies as far as clutch kits. Im looking to buy somethings either oem like or a little better but with the same feel. also, just a Pressure plate and clutch. I doubt the flywheel is damaged.
View 8 Replies
So after replacing my shift forks in my 20th, installing a new clutchmasters fx100 clutch kit with a LWFW I've become a victim of the typical clutch disengagement issue.
In a nut shell car doesn't go into gear while the car is running. System is fully bled with no leaks and a brand new slave installed supplied by CM.
My understanding is the early FML code o2ms in the 20ths can not make use of the NLS shim kit and a stainless line is not a 100% fix.
Who's solved their disengagement issues and how?
View 6 Replies
So I was on the free way in 6th gear and decided to get on it, the rpm's shot up and I barely picked up speed. It's only a slight clutch slip tho only really noticeable in 6th gear so I was wondering what clutch I should go with because I was planning on going BT eventually.
View 3 Replies
Just recently bought a 04 gli. When I shift in to 3rd and let off the gas there is a weird grinding rubbing like noise. It only makes the noise when it's in 3rd gear...
View 3 Replies
So last night I was driving home from work, and at a red light while i was waiting to go i had my clutch down when light turned green i tried to go and noticed i could not put it in gear and that my clutch pedal was stuck in place. i didn't know what to do so I checked my shifter plate everything looked fine so went to look at the pedal and i pulled it forward and it came lose. I started it up everything was fine and back to order. This morning going to work same thing happened again, I don't know what is going on and what could be the cause?
View 5 Replies
I recently got the GTI 1.8L 337 with 64,000 on it. It had been sitting, with daily start-ups, for about 8 months until the ALT was replaced. I've been driving it for a month with no problems until last week. At first I noticed the clutch pedal would pause on the way up for a split second then tap the bottom of my shoe. I thought maybe it needed adjustment but nothing serious. A few days ago the pedal would stick at 3/4 of the way up, and stay there most of the time unless I raised it with my foot, till the car warmed up a bit. Yesterday and today the pedal started to stick 1/4 of the way up, unless raised with my foot, at the morning start-up and will only come up 3/4 when warm. It also wont go into reverse at initial start-up until it gets really warmed up, shifting into other gears is fine. I've had no problems or real sounds shifting into any other gears, though out of 1st has been a little jumpy.
View 3 Replies
We were headed home the clutch pedal went soft... Ok, I thought it's either the clutch master or slave. I get it home and replace the master and after bleeding I had good pedal feel.
Great I thought, I got lucky and it was only the master. Drive it around for a bit and get on the highway and just as I was about to downshift the pedal went flat to the floor again.
Well after pumping the pedal until it had good feel again I got it home and bleed it a couple more times just to make sure I got all the air out. Drove it again. Same thing, after a little while the pedal gets soft again.
Now before I go and replace the slave is it possible I have a faulty master? Having issues after replacing the master?
View 3 Replies
Noticed recently that my clutch is starting to slip. It only seems to happen when I'm cruising in 6th and floor it. When the boost spikes, the revs will shoot up ~750 rpm and then settle back down before the car starts to pull. It is chipped Unitronic Stage 2 with some other bolt-ons.
What I'm wondering is, should I just drive it like this until it really starts to go, or should I replace it now? And what are my options for a new clutch? I don't want to big turbo this car, so the most it could get is a few more bolt-ons. I'd like a stock feeling clutch.
View 8 Replies
Noticed the other day my clutch pedal trim is coming off... What did you do to fix it?
View 8 Replies
I just bought a 2005 GLI and when i test drove it the Clutch was extremely light when I shifted, I have never drove a gli before. Now after researching and further driving i think the clutch is going out. am i right? if so, should i bother putting in a new stock clutch kit or should i go stage one etc...
View 3 Replies
I keep finding air every time i bleed my clutch. I am not losing fluid but i can not figure out whats causing my problems. The pedal is soft at first and then gets harder and it sometimes needs pumped before i change gears or to even get into gear. I am afraid its the slave but i also just may have air in the system.
View 8 Replies
I just replaced my clutch and have put everything back together, and bled my clutch line, but I have absolutely no pressure still in my pedal. I read that u need to make sure your brake fluid reservoir is filled to the max, but following the clutch line, I dont see it going to the reservoir? I also read that the master cylinder is behind the clutch pedal, does the master cylinder hold any fluid that maybe I lost during the bleeding? I'm at a loss right now.
View 12 Replies
Just got in my car and the clutch went to the floor and stayed there when I stepped on it. What are the steps to diagnose this problem? I'm assuming my slave cylinder went kaput!
View 11 Replies
