GTI 337/20th Anniversary :: Broken Glove Box Handle - Replacing The Door
May 23, 2009
Most of the info I could find recommended replacing the entire glove box, and removing the center console to do so. I found a replacement door on ECS tuning's website, but I can't find a DIY on replacing the door/lid only. Any way out on replacing the door only, are the same steps required/removing the center console and taking the entire box out, or can the ECS tuning lid be fitted without as much disassembly?
View 12 Replies
Advertisement
Just replaced the door lock up/down on a 2001 golf. After getting the door all back together I pulled the door open and the door handle popped out slightly at both ends. What happened? It now wont reset into the door flush like before.
View 2 Replies
1996 K2500 Sub. My driver's door inside handle broke. I can get just the handle, or the whole inside unit w/handle for about the same price. Any difference in installation? One easier than the other?
View 1 Replies
The right side of my driver side door handle recently came detached, and I can't get in my vehicle unless I crawl in through the passenger seat.
View 7 Replies
We just bought our 2008 Elantra. The door handle just fell off. I have a warranty and have been trying to get the dealership which has been futile. The handle is plastic. I am tempted to just glue it. This is not the greatest first problem to have right after buying the car and bein unable to reach the dealer.
View 2 Replies
Driver's inside door handle no longer opens door. Need to lower window and open from outside. 2009 Sonata GL?
Apparently the plastic connector/retainer to the door latch cable is broken off so that the handle no longer moves the cable.
Does the replacement door handle come with the connector/retainer to the latch cable?
To complete this repair, does the whole inner door panel have to removed or simply the assembly around the door handle?
View 6 Replies
I have a 2002 xlt excursion. My passenger rear door handle is broken. It is the plastic clip that hold the linkage rod to the assembly (slotted) inside the door. I can't find a diagram to get a part number. Just not very technical looking things up... looking for a parts diagram or a part#?
View 2 Replies
I have a 2007 Sonata and the rear driver side exterior door handle broke. How to repair it? Does the interior panel need to come off? I see a screw under the pivot side and an interior bolt through an access port from the inside.
View 1 Replies
Trying to replace a right rear door handle on my 01 7.3. Attached is a photo of the new handle with the unlock rod. Also is attached is photos of the door without handle. I pointed to the part that moves the lack to unlock.
Looking for the clip part number or photo that is missing. I thought a hose clamp would work maybe with a nut on the rod?
View 6 Replies
I was driving today and when attempting to go to fifth gear and sixth gear the shifter went completely loose, but if I returned it to neutral and go back to 1st through 4th I regain feeling of the shifter. Could something within my shifter box be box be broken? I can go into fifth and sixth manually from the shifter tower on the transmission,
View 3 Replies
its cracked and its leaking i was tld its 210 dollars to replace it... what is the part number for this??? or is this not that bad of a deal?
View 2 Replies
I looked through the MKIV DIY stuff but didn't see one. My serp belt is in need of replacing soon. Seeing some cracking on it for sure. According to records from the PO it was bought as part of the timing belt kit at the end of '09 so I imagine it was changed then...just didn't think it would be so cracked so fast!
Anyway, looking to replace it in the coming weeks. If I could be pointed in the right direction that would be awesome. I do have a Bentley, but I find how-to's on here to often be better. But if I need to just follow the Bentley, I can do that too.
View 24 Replies
Two weeks ago had to replace my ECU due to failing. Got a new one, reflashed my Uni software and the only code left after the ECU was replaced was the Air Intake Temp Sensor. That was 12 days ago. Today, get home. Car was running smooth all day. No issues. Go out and start the car and my idle is at 1300. (Normally 750) I have zero throttle response. I've unhooked the battery twice to do a reset, unplugged the throttle body sensor and plugged back in, still got nothing.
View 9 Replies
I'm new to VW but I just replaced a manifold hose and now my car keeps shutting off but if I let it sit for like 5 min. It starts right up. The hose that came on it was plastic n I switched it to a rubber one from advanced.
View 12 Replies
so i've had my 337 for a couple months now and when i first got it i found 2 broken vacuum hoses that were causing misfires. once i got those replaced my CEL went off and seemed to be running fine other than from time to time when i started it up my idle would be around 1.2k rpms and then after a couple miles itd settle down to 750-800 rpms but it wasn't rock solid, so obviously there is still something wrong.
on my drive home tonight from work i was in the mood for some spirited driving but when i'd hit the gas i could feel some hesitation through the powerband at wide open throttle. when i got home i turned it off, and started it back up to see if it was idling funny and when it ignited the rpms jumped to almost 2k and immediately fell back down to 1.2k.
My thoughts are its either a vacuum leak again, bad/dirty maf, dirty throttle body, or a boost leak.
View 1 Replies
I have a 2002 337. My gear selector has broke down under the boot.
Can I replace this part? Where can I get one? How do I get the old one out?
View 1 Replies
I replace my timing belt and water pump and my engine is now over heating. I notice it's only over heats when the ac is running and the engine is idling. When I start to drive the engine temp goes down.
View 1 Replies
(6 speed)... I have faulty reverse lights, my speed sensor is working so I am sure it isn't the fuse, I am guessing this means the switch/sensor is broken. Where it is located, and what the correct part number is?
View 3 Replies
My 20th Ann. GTI randomly would not go into first or second (they move into place but are just limp there and not catching into the gear) I was told for replacement of new 6-speed transmission and they did not offer any alternatives beside replacing it completely.
I know there is a thread talking about this but I read about the shift fork, or a piece of the shift fork that breaks and this problem fits my exact description. Not much info on what I can do, or at least not specified. What is any cost effective way to get my gears back without completely replacing the transmission? Is there anything I can do to just replace a broken part or are there any alternatives?
View 14 Replies
Ok, got in a fender bender a few weeks ago. The plastic strips (with the Torx screws) holding the headlight steady, broke from the impact. The headlight itself is fine, no glass was broken, headlight still works, but without those plastic things, it will not, of course, stay still. My question is...would I need to buy a whole new headlight just because the plastic tabs are broken?
View 5 Replies
I had my '09 F-150 Super Crew lock punched out on driver side door. To prevent this from happening again, I am replacing that handle with a handle for the rear door that has NO lock. I will no longer have key access to the truck. I am also ordering a spare remote. Is there anything I should consider before following through with this decision? Why I shouldn't do this? Is this a common thing to do?
View 14 Replies
