GTI 337/20th Anniversary :: 2005 - Shake And Idle Hard When Gets Under 1000 RPMs
Sep 18, 2012
I have a 05 gli I just put a k04 turbo on. It runs on stock ecu but I have been told that's not the problem. When I start the car the rpm's spike to around 3 grand then slowly drop to normal idle rpm's when it gets under 1000 rpms the car starts to shake and idle hard. Idk what it is Cel is on and read misfires in 3 of 4 cylinders but checked plugs and everything they r fine. I'm thinking maybe vacuum leak or something along those lines.
View 6 Replies
Advertisement
I have a pretty bad flex pipe leak on my 20th. Would this leak cause a very rough idle almost stalling when I come to a complete stop. The Idle fluctuates from almost stalling to 1000rpms.
View 1 Replies
I have a 05 gli and when in idle the rpms go down really low then shoot back up. what could be the cause and how would i go about fixing this?
View 1 Replies
Have a jazz blue chipped tuned with giac.. It does this random times.. When I come to a red light on idle the rpms go up and down just a bet but never stalls. The car vibrates and the engine shakes a bit. Engine is stable when car is on and off. Idk if its motor mounts or what?
View 10 Replies
About a week ago I noticed my RPMs suddenly dropped while I was driving. a couple days later after driving the highway for about 45 mins, averaging probably 80-90mph, I got into town and I stopped for a car to park. Then it just stalled, I didn't notice a kick back, it's like the car just shut itself off. It took probably 10 attempts to start again. About a mile down the road it did the same thing pulling up to a stop light. I sat through 2 light cycles before it started again.
Got to my destination was there for maybe an hour, when I left the car started fine. Drove for about another hour on back roads when the Rpms started dropping again and I would need to dump the clutch to get them to go back up. Then my screen started beeping telling me to STOP with and oil pressure alert. I ended up driving the car home dumping the clutch whenever the rpms would drop. Once I got home I had my boyfriend take it out and nothing... Of course... A couple days have gone by and it hasnt been as bad but it still drops every now and then, and today after driving home maybe 5 miles it stalled again...
I've plugged it in and my speed sensor is throwing codes, but I don't think that's the entire problem. Whenever my car acts up the EPC light comes on but no check engine light so far. 2005 Jetta GLI 1.8t.....
View 2 Replies
Just checking in to see where you'd recommend to start looking for a rough idle issue. It seems to get worse once the car fully warms up. I took a vid, and although it may not seem horrible in the video, it sometimes causes throttle lag from a stop and causes the car to get close to stalling when falling from high RPM's. Take a look at the video .....
View 2 Replies
The car will start up fine, run for 10 - 20 min and stall. I will try and restart it but i takes atleast 7 or 8 sec of the car just turning over before it slowly fires up. Which results in a high idle 1200-1400 rpm and the car stalling another 5 min later.
Ive fixed my o2 sensor the wire was cut, replaced the fuel filter, and got a eurojet lower pcv hose for the vacuum leak i found.
View 4 Replies
2012 SEL... Experiencing High Idle (1000 rpms) when the AC is ON. When I power the AC system OFF... the idle comes down to 700-800rpms. Then I power the AC back ON and it stays for the rest of my trip. Restart the car, and it's back to 1000 rpms with the AC on.
View 2 Replies
My 2001 BMW 325Ci has an occasional "surging" idle problem. When coming to a stop or at idle, the engine will rev between 500 and 1000 rpm's. Sometimes it will correct the problem and idle normally, or keeps surging until it eventually stalls. When restarted it works fine. Tried fuel injector treatment, fuel stabilizer treatment, and replaced thermostat. Still surges about 50% of the time. Had it to a dealer, and computer says its running fine.
View 1 Replies
I have a 2005 Chrysler 300C ( original owner )Mileage 172,000 and I take care of my car. I use full synthetic oil and change it every 5000 miles. I noticed a hesitation between 1000 and 2000 RPM's. It disappears after 2000 RPM's. The Chrysler dealer kept doing repairs and claimed the problem was gone and it is still there. The dealer did a full tune up, induction service and also replaced the EGR valve, gasket and seal. The problem gets worse in higher mountain altitudes.
View 3 Replies
My mother has a '04 Santa Fe 3.5. Her automobile makes a rattling/grinding sound when around 1000rpms/idle. However, the sound disappears when accelerating and drives like a charm. The sound returns once again around 1000rmps at idle or stop. I have changed the oil pan, replaced oil and filter and even put in a new battery. I'm not an aficionado when it comes to Hyundais (Subaru driver here).Car also has 180k miles.
View 6 Replies
I have a 2003 Ford Musang 3.8L v6 when I start my car for the first time of the day or after several hours of sitting the car idles high between 1000-1300 RPMs for approximately 15-20 seconds after that it idles down to 600-800 rpms. I changed the spark plugs wires air filter not sure what else it could be no Check engine light.
View 1 Replies
I have a 2008 Ford Focus - 4 Door Sedan SE 60300 miles.
I've gone to 3 mechanics now and no one can seem to figure out whats wrong with my car. Here's whats happening:
About 1 1/2 years ago I took my car to get an oil change at Jiffy Lube (Yeah never again). When I left, my car was idling funny... Silly me didn't take it right back and have them tell me what was wrong.. so I let it go, well about a month later it started idling even weirder. Basically it feels like my car is shaking when it gets under 1000 RPM and I notice my RPM dial start falling and bouncing back, acting like its going to stall, but never does. I notice a loss of power when this is happening (on speed up and just accelerating in general). All of this is random, I can't seem to put a pattern to it as to when it happens. One day I'll start it up and everything is perfect... Then I'll shut it off and restart it later, and it starts vibrating and puttering again... No signals as to if its hot/cold or wet/dry, no environmental variables seem to cause it to happen anymore than others. And there is no check engine light on, everything "looks" normal.
What I've had done to it so far is:
Air filter changed / reseated
3 oil changes (keep getting told it will work)
Throttle cleaned
Computer reset for idle sensor data rebuilding
Now I'm told that I need new engine mounts, and that could be the reason for the vibration. I'm thinking that the vibration caused the mounts to wear out, more so than the mounts being the cause. Mainly because I don't see how bad mounts could cause loss in power/bad idling.
What could be wrong?!? Really bugging me and don't want to keep throwing money at it for phantom solutions. Seems like mechanics I go to can't figure it out unless there is a check engine light on with some diagnosis code to tell them exactly whats wrong.
View 8 Replies
My car is a 2001 honda accord v6. It sat for 3 winter months. When I go to turn it on in the morning, the car will rev while idling. Jumping between 1000 and 3000 rpms. Why this might be happening?
View 3 Replies
Well, it's looking sort of depressing for my '06 Sonata! I had an oil change done yesterday and now I'm getting a Low Oil Pressure Light on idle under 1,000 rpm's. Today the check engine light came on and it's code P0021.
I also experience very noisy "bearing" type noise upon start-up which happens for about 10 seconds or so. This has been going on for a month or so.
During my online research it's appearing that I may be suffering from the dreaded Timing Chain Tensioner I've read a lot about.
I'm aware of the TSB (10-EM-006) and have a copy of it if needed.
My question is this...my Sonata has 151,000 miles on it, well beyond the 100k warranty period. Will Hyundai repair my issue as a warranty item under that TSB?
View 8 Replies
I have several problems with my 06 FEH maybe some of you had same issues. I have imported this car from new york in my country 1 month ago, this is first Ford for me. Love this car but there is some issues and want to figure them out.
1. seat heating is turning on without clicking on the button, but not always it's random. Often on passenger seat some time on driver side to. I try to disable fuse but it also for 4x4 so it's not an option.
2. My engine idle RPMs is always higher that 1000. Maybe it is normal but want to be sure.
3. car cannot climb the hills here is the video.... car is just doing nothing to climb no rev up no trying just stall in middle. In my country there is some roads with hills like this and I want to visit that places.
4. Cruise control is working random to maybe it will start speed control in one click or after 20 -s try.
5.Is there any way to see soc? factory unis is replaced in my car with aftermarket radio. I have elm327 and tourque pro but can't find that option.
6. When monitoring with obd water temperature is always lower then it was on my other cars. its around 158-176F on other cars it was 200F.
YouTube......
View 2 Replies
2010 F150 ... So I have the tick noise at rpm's 800-1000 at drive through, stops, etc. So I did research on it a few months ago and saw that it might be VCT's but should be able to drive. so I drove it waiting to save money and have it go to a shop. well this past weekend while coming home from work my oil light came on the pressure dropped to zero, I was on the highway so I drove about another mile to get off highway and once I got off my truck died. I had it towed to my house and I thought I blew my motor. So I started doing research here and found that the VCT's AND cam Phaser could be bad. so I replaced my VCT on driver side put it all back together it started and loud knock was gone. then after 5 mins it was back very loud knock!
So I shut it down and took apart the passenger side once I got the valve cover off I found the problem.... The bolt that holds the cam phaser in place snapped off and was riding along the camshaft. So I took that out and extracted remaining part of bolt. inspected my camshaft and it was really messed up. so I bought new Phaser and Camshaft. the camshaft just came in today and I am trying to put it back in. but the hole for the pin in the phaser doesn't line up and I cant spin the shaft to make it line up. should I spin the cam phaser? I marked the chain and the phaser is where it should be on chain, but with that bolt snapping off could that have thrown the timing off so my mark is no good? when I lay the camshaft in place it sits perfect and if I just move the phase over 2-3 links it will all fit together. Should I do that?
View 5 Replies
I recently picked up a 2004 Mercury Mountaineer, 4.0 with 113,000 miles. OBD reader says misfire on 3 cylinders.. Installed new plug wires first.. nothing.. going to install plugs next when she is cold. Now, am I really looking at replacing the coil pack to end the misfire codes? She likes to buck and shake and idle around 400 rpms.. I know that is too low..
View 4 Replies
So my 20th AE has been wrecked. But here is the issue, the car will idle for a about 30 seconds to a minute but surge from 1500 rpms to around 750. But after that, it won't idle. If I let it sit for a couple of days, then it will idle for a little bit then die again.
View 2 Replies
So about a week ago i got on the onramp to get on the freeway and stepped on the throttle as usual to get up to speed, but now for some odd reason the rpm's dont go past 5,500. Not sure whats wrong. I stay on the throttle but it pretty much stops and levels out at right around 5,500.. i must say i am pretty clueless. i just past 80k not long ago, and everything seemed to be going fine.
View 3 Replies
I bought my gti about a month ago and every time I warm it up in the morning or any time it has been sitting over a long period of time the rpms sit at about 1300 until about a minute and it goes under 1k ... I am not to familiar with this issue.
View 14 Replies
