GTI 337/20th Anniversary :: 2003 - Zero Resistance When Clutch Pedal Pushed
Jul 15, 2011
My clutch has been feeling very strange lately, and has had a mind of its own. I have looked underneath myself, and have even taken it in to two transmission speacialists and they can't figure it out. The master cylinder isn't leaking, and the slave cylinder is fine as well.
Here's what is going on with my clutch...
- I will push in the pedal, and there will be ZERO resistance until about 1 inch from hitting the floor, then all the pressure is there, and I am able to shift. However, sometimes I won't even be able to put it into gear because the clutch won't engage.
- Then I will pump the pedal, and slowly I will gain a little more room on the draw of the clutch, and it will feel fine. All the way to the point where a few days later it will be driving like new.
- Then it will start feeling funky again a few days later and the cycle starts over.
I drive a 2003 GTI 20th AE.
View 6 Replies
Advertisement
Started losing pressure on my clutch pedal yesterday. When I would push in the clutch pedal it would not push back up to the reset position. It would only come back up half the way. Now today I have a steady ABS light and ASR light on. Checked for fault codes and found no trouble code. Checked brake fluid resevoir for leaks; still has plenty of fluid. Checked slave cylinder bleeder valve for leaks and looks dry. The only thing I think it could be is the clutch master cylinder. If I drive the car for a few minutes I am able to build pressure back up in the clutch, however the ABS light and ASR light still remain while driving. Turning the car off and back on again shuts off the light for a few minutes until I start driving, but the clutch pressure starts back low again.
View 3 Replies
So last evening, I went to start my car and the clutch pedal went straight to the floor with no resistance. Car started and was extremely hard to get into every gear. Felt like the only thing pushing the clutch pedal back up was the spring underneath the pedal itself. Clutch pedal was 100% just the day before. Got the clutch line bled (vacuum bleeder) and it worked fine again.
Any clue as to what could caused this overnight?
Its a AWP 1.8t jetta with ASR.. I believe I came across something about a revision in the hydraulic line but I'm not sure.
View 3 Replies
I recently got the GTI 1.8L 337 with 64,000 on it. It had been sitting, with daily start-ups, for about 8 months until the ALT was replaced. I've been driving it for a month with no problems until last week. At first I noticed the clutch pedal would pause on the way up for a split second then tap the bottom of my shoe. I thought maybe it needed adjustment but nothing serious. A few days ago the pedal would stick at 3/4 of the way up, and stay there most of the time unless I raised it with my foot, till the car warmed up a bit. Yesterday and today the pedal started to stick 1/4 of the way up, unless raised with my foot, at the morning start-up and will only come up 3/4 when warm. It also wont go into reverse at initial start-up until it gets really warmed up, shifting into other gears is fine. I've had no problems or real sounds shifting into any other gears, though out of 1st has been a little jumpy.
View 3 Replies
We were headed home the clutch pedal went soft... Ok, I thought it's either the clutch master or slave. I get it home and replace the master and after bleeding I had good pedal feel.
Great I thought, I got lucky and it was only the master. Drive it around for a bit and get on the highway and just as I was about to downshift the pedal went flat to the floor again.
Well after pumping the pedal until it had good feel again I got it home and bleed it a couple more times just to make sure I got all the air out. Drove it again. Same thing, after a little while the pedal gets soft again.
Now before I go and replace the slave is it possible I have a faulty master? Having issues after replacing the master?
View 3 Replies
Noticed the other day my clutch pedal trim is coming off... What did you do to fix it?
View 8 Replies
I keep finding air every time i bleed my clutch. I am not losing fluid but i can not figure out whats causing my problems. The pedal is soft at first and then gets harder and it sometimes needs pumped before i change gears or to even get into gear. I am afraid its the slave but i also just may have air in the system.
View 8 Replies
I just replaced my clutch and have put everything back together, and bled my clutch line, but I have absolutely no pressure still in my pedal. I read that u need to make sure your brake fluid reservoir is filled to the max, but following the clutch line, I dont see it going to the reservoir? I also read that the master cylinder is behind the clutch pedal, does the master cylinder hold any fluid that maybe I lost during the bleeding? I'm at a loss right now.
View 12 Replies
So last night I was driving home from work, and at a red light while i was waiting to go i had my clutch down when light turned green i tried to go and noticed i could not put it in gear and that my clutch pedal was stuck in place. i didn't know what to do so I checked my shifter plate everything looked fine so went to look at the pedal and i pulled it forward and it came lose. I started it up everything was fine and back to order. This morning going to work same thing happened again, I don't know what is going on and what could be the cause?
View 5 Replies
Coming to a stop, clutch pedal just lost all pressure. I can bring it back up, but even the slightest touch will send it to the floor again. I get the brake warning light on the dash. What could be causing this?
View 7 Replies
I have an Imola 20th and recently i have been having some problems with my clutch. The pedal goes from being soft to very hard when its close to disengaging. It also engages very heavily when I go to let it out. This only started happening recently when temperatures started to drop if this has any effect on a clutch. Also, I replaced a shift fork two months ago and was curious if there was possibly anything going on with seals around the slave cylinder.
View 2 Replies
The transmission is a Six-speed MQ350 transmission in an MKIV 337 GTI.
I was driving last week and ran over a large snow chunk, heard it hit the underside of my car. A mile down the road my foot is resting on the clutch pedal at a stop light, and the clutch slowly went to the floor. It was still drivable, barely. The clutch came about an inch off the floorboard, but still caught. So i pull into the parking lot ahead of me, and was barely able to move the shifter left to right nor would the shifter go into gear. There were no fluids coming from under the car, nor could i see anything that looked wrong. I turned off, back on again. nothing. I then pulled the clutch pedal up from the floor and it went back to normal. Everything seems normal now, but the shifter seemed a little sticky yesterday from left to right.
View 6 Replies
Recently my clutch started acting strange, the pedal felt softer and eventually after I pressed it in it stayed on the floor. After pumping it, everything went back to normal. Next day, still same thing, no pressure in the clutch pedal. I checked the brake fluid and it's full. There is also no sign of any leak. Took the car to the mechanic, he recommended changing the master cylinder. I changed it but still nothing. I tried bleeding the slave but every time I bleed it, it has air in it. So I'm stuck and don't know what should I do next. I think it might be my slave cylinder but I don't have a place or tools to do it myself. I'm pretty sure the entire tranny needs to be pulled out to remove the cylinder. I also read that most people change the clutch when they replace the slave.
View 10 Replies
So your clutch pedal operates properly, the clutch engages with no issues, but this annoying squeak, snap, crackle, and pop noise keeps coming from the clutch pedal within the cabin.
Could it be your clutch master cylinder? CMC is not leaking in the engine bay and the driver footwell. Not the CMC.
Could it be your clutch switch that's used to control revs and cruise control? Removed it and clutch pedal still made noises when pressing and releasing the pedal. Not the CS.
Could it be the over-center spring that sits behind the clutch pedal assembly? How could it be? It's just a spring. Springs that compress in that orientation don't make snap, crackle, and pop noises.
What most people fail to realize is the noise is coming from the pedal assembly, but it's not the pedal structure or the pedal. It's the pivot point where it mates with the clutch pedal mounting bracket. At the pivot point are two bushings (one on each side of the pedal structure) that wears out over time creating these noises.
Please look up the part number for these bushings. They look like the following at this link but these are aftermarket upgrades for BMW's.[URL] ....
View 4 Replies
I have a co-worker that is having trouble with his 06 passat. He explained that the clutch pedal has no resistance and is on the floor. The dealer he took it to is saying he needs a new clutch and pressure plate claiming that the "pedal doesn't have pressure on it is because the clutch discs won't engage" which sounds backwards if you ask me. Anyway, what could this be? Where could we start tracking this down?
View 13 Replies
Last night I was driving home and decided to show off at a light. I punched it pretty hard, but it wasn't anything outrageous.. anyway, as soon as I shifted to second, my clutch pedal gave out and dropped to the floor without resistance. I coasted it to a gas station, luckily.. When I lifted my foot the pedal rose back slowly. I tried pumping the pedal, didn't work. I looked for leaks, but none were found. I turned it off, put it in first and tried starting it, and it turned over and jumped/jerked forward, a lot like it did right when I shifted into second and it went out. So I'm assuming that its not the entire clutch cause it wouldn't have engaged the engine. It's not a leak. pumping it didn't work so it's can't be a pressure issue.. what is going on? is it my master cylinder, or maybe my slave?
View 7 Replies
Just went to leave my apartment and I get at the first traffic light and put it into neutral. Light turns green and I try to put it into first and it won't let me... In fact I cannot shift into any gear while the car is started. Put the flashers on and I am stumped. There was also more resistance in the clutch pedal as soon as this happened.
I turned the car off and tried wiggling it into any gear. For some reason while the car is off I can put it into any gear. So I had to put the car in first gear and start it and limp it home. I had to rev the engine to about 2,800 - 3,000 RPMS in order to get the car to bite and take off. Shifting into any other gear while driving was a hassle and it felt like there was a lot of resistance.
Just did some quick Vwvortex recon and some people are saying that it is a broken pressure plate? Pressure plate welds itself to the clutch? Or possibly a throwout bearing? Also what Transmission is in a 2003 Passat 1.8T Engine code AWM.
View 2 Replies
Since I have gotten my Sentra 2003 I have had issues with it. This past year my thermostat went about 6 weeks ago. I noticed that when my car would idle the engine would rev. Over the weekend I drove on the highway for 2 hours. When I started slowing the speed don I noticed that I could press the clutch pedal all the way to the floor without any resistance. It came back up. I rolled into the toll plaza and stopped to pay the toll at which point I could shift the shifter into a gear but the car would not catch. No movement. I think my clutch mechanism needs to be fully replaced as the car has 115000 miles with the original still intact. IS that most likely the case and what am I looking at for the cost?
View 2 Replies
I have a 2001 Saturn SL2, with a manual transmission. The clutch pedal recently gave up -- it goes to the floor with no resistance, and I can't shift. I understand that this car has a hydraulic clutch, and that the hydraulic system has failed. My mechanic says the whole transmission system should be replaced, (though he hasn't been able to look at the car 'cause it's stuck in my driveway!) Before I donate the car to charity, could the problem be anything simpler? Or is it a straight forward diagnosis?
View 11 Replies
Experienced a chatter in the clutch pedal with the a/c on when clutch pedal is pushed in. To me it feels like the throw bearing isn't disengaging the clutch fully, plus my clutch is kind of high once full disengage unless its normal.
View 5 Replies
I have a 5-speed transmission pickup (’04 Ford Ranger EDGE SuperCab). Clutch pedal feels "normal", No resistance when shifting gears. Will go into gear with ease, except for 2nd gear (grinding noise), must push clutch to the floor and still grinds; but only 2nd gear. In 1st gear, my truck will slowly creep forward as if unable to engage and not having any kind of pulling power. Even when shifting to 2nd, 3rd, 4th and 5th gears, it barely maxes out at 30MPH (top speed unless vehicle is on a slope or slight decline then I can get up to and over 40MPH. Checked brake fluid level, it’s ok. The fluid’s at max. Clutch is relatively new (April 2014), with only about 13,000 miles on it, if that. It must be cylinder issue. Is there any way to tell whether it's the clutch master cylinder or slave cylinder?
View 5 Replies
