GMC - Sierra :: 1995 - Runs Rough And No Power
Jun 17, 2014
I have a 1995 GMC that I have owned since new. It has 212,000 miles on it, a 305 TBI, and a manual five speed. It started running bad all at once. It idles rough, at different speeds and never settles down, (between 900 and 1300 rpm. It smells like raw gas, smokes, and has no power to get started from a stop. I checked the vacuum, it is at 19" at all rpms. The MAP sensor reads 0.3VDC when off, 4.12VDC when idling, and 1.5VDC at WOT. It appears to have 12PSI fuel pressure (after a messy test set up!) on the fuel pump side of the fuel filter (filter replaced 10,000 miles ago). The EGR valve appears to cycle OK when I suck on the vacuum line so I assume it works OK. I found a bad TBI flange gasket and replaced it. It runs slightly better but still smells like raw gas and has no power. When I try to accelerate, it immediately has no power, like a big vacuum leak. The idle is close to normal (900rpm = normal). Do I just start replacing parts?
View 9 Replies
Advertisement
1995 G20 5.7L... This van runs great when first started and continues to run fine after it's warmed up and will do so until it’s turned off and restarted. When first started vacuum at idle is steady at 21” and 10” at 55mph cruising speed. I can continue driving for an hour or so and it will continue to run fine. It's only when I shut it down and restart after 20 minutes or so that I have a rough running condition. After parking for 10 to 20 minutes and restarting idle is still steady at 21” vacuum but the van hesitates on acceleration and runs rough at cruise with a 5” vacuum. If I continue to drive I get low vacuum trouble codes for the MAP and Oxygen sensors. I’ve replaced the oxygen sensor and performed a diagnostic on the MAP sensor which checks out ok. I’ve checked for vacuum leaks – none found. I've replaced the spark plugs, cap and rotor. What to look at next?
View 8 Replies
So I have a 95 aerostar 3.0. I use it every day my a delivery vehicle. I keep it maintained. About a month that ago, it developed a skip or a hesitation, most!y at high speeds, usually under load. I thought it may be transmission but had it checked and was ok. I drove it like that for several weeks. Then got worse so I parked it for ten days until my mechanic was available. When I cranked it to drive it over, it spit and sputtered the whole way here and barely made it. It had never done that before. He changed plugs and wires and distributor cap, even though it had been less than a year since all that had been done. Still no change. Driving way worse after sitting for ten days.
View 6 Replies
I have a 87 gmc sierra with a 305 tbi motor, i drove it and parked it for a year and it was running fine, i went to go start it again it fired up and high idles for about 5 seconds then dies, I have put fresh gas in it and ran some seafoam threw it, changed fuel filter, rebuilt the tbi system with all new gaskets and seals, injectors seem to work as they should, i have replaced the distributor,and the cap and rotor, new plugs, IAC, coolant temp sensor, map sensor, egr valve, egr solenoid,, new oil and filter, and checked all vacuum lines, grounds,checked all the sensors with the ohmn meter and all getting the correct power, its pretty close on timing, i just cant seem to figure it out, it will idle high and sound good then fall on its face, the only way to keep it running is you have to pump the peddle, it wont rev up at all it just sputters and dies.
View 1 Replies
My truck runs very rough and lacks power when cold, even during the Texas summer. Once it warms-up, everything is fine. It's almost like turning on a light switch. If it's plugged in for a couple/few hours, it's smooth as soon as it starts. I'm assuming it likes the oil once it reaches a specific temperature. What my problem is?
View 14 Replies
My 2001 V70 24T runs smooth when cold as it warms up it runs rough with delayed acceleration reaction ....
View 1 Replies
I just bought this nicely used 1991 GMC Sierra 1500 series pickup truck for $650. It started up and ran fine when I gave the seller the money - the few leaks in the break lines.
Easy fix right!
So my son (19 that knows it all) and I went and changed all the brake lines (made everything one size 3/8 line.) Filled it up with break fluid and started the truck. I had my so pumping the breaks and holding them (his first time) I bled the far rear (passenger side) then I had him turn the steering wheel to the right so I could bleed the front driver side.
He turned, and turned and turned until the engine died.
Now the truck only runs when the steering wheel is turned all the way to the right or all the way to the left.
Going to pull the codes to see what the heck is going on....
View 9 Replies
THE FREQUENCY: This is a condition that has become progressively worse over the last six months. Initially it occurred once a week and now it is happening almost every day, lasts longer and is more acute.
THE SYMPTOMS: Initially and randomly, while driving at any speed, the car would begin to hesitate as if it might stall but did not- The hesitation was much like a shudder or power loss. At this time the check engine light would blink and stay on for a couple of days. This whole event would last less than a minute and the car would return to normal until the next one.
Now, six months later, it is occurring almost every day. At startup, at low speeds, at stop lights.... A LOT!
WHAT HAS BEEN DONE SO FAR: After frequent and unsuccessful visits to the Volvo Dealer all the plugs, the wires, the cap, and the rotor have been replaced with no luck.
The dealer says the code indicates a misfire on the #3 cylinder.
View 3 Replies
I have a 1994 Ford F-150 pickup with a 4.9 litre fuel injected inline six. Truck ran fine and took me to my destination but after sitting for 4 hours the truck would not start. Engine would turn over normally and could hear fuel pump running (didn't seem to stop) but truck would not start.
I changed fuel filter but truck would still not start. I removed air filter assembly and poured starting fluid in the air intake and engine started but idled roughly. Engine will rev up but runs very rough and lacks power when driven. Also the check engine light stays on.
View 14 Replies
I have an 02 2.4 gas SF. After a good while, the car will run rough, lose power and will not take any throttle. As if it is starving for fuel. But it will idle fine and if it does stall, will restart. On a hill, I have to drop into first and keep it at 1000 RPM (yikes!)
If I keep going with very little throttle, it may resolve itself. It is always fine after a complete cool down. I checked for vacuum in the tank by opening the filler while it was misbehaving. I have a new CPS, new coil packs, new filters. I've have enough gas fill ups to eliminate water in the gas.
It has thrown no codes. I went ahead and ordered a MAF sensor and a cam position sensor...just guessing. (it had failed emissions which I resolved by cleaning the MAF.)
View 16 Replies
I just changed the plugs and wires on my 2008 Ranger 3L. Now it runs rough with no power. It was fine before I did the work but I thought I should change the plugs at 215000KM. I used Ford wires but unfortunately I used Bosh platinum plugs and now think I will change to Ford plugs. Do you think the Bosch plugs would be that bad for the Ranger? What is the belt tensioner torx size? I had to move the A/C compressor over to get the #4 plug but had a very hard time trying to loosen the belt.
View 7 Replies
'03 6.0 Powerstroke. Rough idle AFTER it warms up. Runs fine cold. It seems to studder and miss at mid range acceleration. Egr deleted and new oil cooler installed. New lift pump. Replaced ICP sensor. Have 48.5 volts at the FICM. Replaced the fuel pressure spring to the blue one. All new filters. Does not smoke. Does not throw codes. I need to fix this truck one last time. It has a date with the bottem of a very deep lake! It has been nothing but a pos since it hit the ripe old age of 25k miles!
View 14 Replies
Our 07 Mazda5 (80k) once in a while will start and run very roughly, and pressing the gas to the floor only gets it to 3,000 rpms.It has diminished power for climbing hills when this occurs. Everytime this happens if we shut the car off and let it sit (between 10 minutes - a couple hours) it starts and runs like a top. We have added drygas 2 of the times, but the last time it happened was on the same tank of gas that we added the drygas to. Check engine light comes on, but will go off after a day or so.
View 5 Replies
i have a 1995 sierra 2500 gas series. then my horn and my washer fluid aren't working. i cleaned all my ground posts and put in new fuses. when i hit the horn, you can hear the relay switch clicking. and, when i first went to use the washer fluid, it squirted once, then stopped. i checked and cleaned all ground posts. i also used an ohm meter on both horns' plugs. there's power coming to the horns???
View 3 Replies
I have my 2002 Ford F250 Powerstroke. 175,000 original miles by me and only me. SCT, MBRP, Howes or Stanandyne almost always. Runs like new. It starts rough if I don't plug it in. Even on 50 degree days. Then it levels off and runs perfectly. If I plug the truck in I can drive off immediately with perfect operation of motor. I just went 1500 miles. Pulling a car hauler with car. NP at all.
New Glow Plugs, GPR "Yes it works", IPR, New Harness, Buzz Test shows it's fine, New #8 injector last year, New O rings HPOP. My buddy who is a PStroke guy said this trucks runs too perfect for it to be injectors. He recommends seals for the injectors. What does this mean. Or what else can it be. Where should I start.
View 9 Replies
My '03 6.0 is hard to start and runs rough when cold. Not just cold outside temps, but engine not up to temp. Starts and runs like a champ once it's up to temp. It was doing this when I got it, but it's getting worse.
From what I've read the common culprits are:
1 - failed solder joints on FICM power supply board
2 - bad power supply side of the FICM
3 - updated flash needed for FICM
4 - injector stiction
5 - leaky O-rings at high pressure oil rail to injectors
I have read up on how to run the voltage test on the FICM with a multimeter.
Seems like I would have to go to a dealer to have the software version for the FICM checked.
I am 100% competent to do the tests and/or repairs myself, but since I recently moved in with my fiance in a condo and my tools are in storage, I will have to do it at a friend's house. That being the case, I want to know what all of the common things are that I may need to check for so I am prepared. So, I wanted to see if there were any other common causes of this issue.
I plan to test the FICM voltage and give FICMRepair.com some business if that's the problem. And if that's not the problem (or maybe even if it is) I will get the injector seal kits and replace all of the injector seals as well as disassembling and cleaning the spool valves in the solenoids. I will also change oil and fuel filters with Motorcraft parts and Rotella synthetic oil while I'm in there.
View 14 Replies
I have a 2001 7.3 with 259,000 miles. It does not get too cold here, however over the past few winters when the temp is below 50 at night the first minute or two of running out of the neighborhood is tough going unless I let it heat up. It has been getting worse over the past few years and now if its even 55 or 60 I need to let it heat up. Glow plugs? Injectors?
View 3 Replies
Car has 252k miles runs ruff after engine warms up, looses power, if I give more gas, car will sputter, but rev up to 5k engine smoothes out. This situation constantly comes and goes.
View 3 Replies
I have an 03 F350 with the 6.0L. It has 210,000 miles on it and the injectors are beginning to be suspect. Its very hard to start when its cold, smokes and runs like crap untill it warms up.
I've found a set of injectors out of a 2005 truck with 8000 miles on them. The truck was overboosted and blew a head gasket.
Now finally to my question.....Can the overboost damage the injector? Would it be safe to buy these and install them or rebuild them before install or just leave them alone?
View 14 Replies
Here's what I'm dealing with. Took the truck on a 1500 mile trip with no issues. Got home and started it the next morning and it started right up. 1/2 mile from home it starts to run rough and wants to die. It does this for a few minutes and then perks back up and runs fine for however long the trip is. It will always re fire and have no issues. Every morning it's the same game as described above. Within 1/2 from home it's doing this. Seems to be fuel delivery related, but why would it start after sitting overnight, and then after its little fit, run without an issue?
No codes in computer.
View 7 Replies
I have a 2001 F350 with the 7.3 standard trans. The previous owner put a toggle switch to control the EBPV as an engine brake, I've never used it. It blows white/blue smoke when cold but has for the last 4 years and doesn't seem any worse now.
Last fall I ran the truck the lowest on fuel that I ever have, the light was on for a long time and I thought I would run out. I made it to the gas station and filled it up then drove home. The next time I drove it I went about 25 miles and it started to buck while going up hill. This got worse and eventually the check engine light came on and it stalled.
It wouldn't start again so I had it towed home. I got it started a couple hours later but it would run really rough and only for a minute or so then stall. It will usually start again once or twice and stall, then it wont start again until it has sat for an hour or so.
I didn't have a code reader at the time so I started reading threads. Here's what I've done to date.
Changed the oil and filter, it was way over do. New fuel filter.
The oil level in the HPOP stays about an inch from the top, I've checked it a few times after its stalled.
Dropped the tank and cleaned the screens in the pick up, no change.
The ICP had oil on it so I replaced it and a new connector, no change.
Changed the CSP with a grey one, no change.
Changed the IPR valve with one from a buddy that was on an engine that was running. The truck ran rough for a min then settled down and ran smooth. I let it idle for 20-25 minutes with no problem so I thought the problem was solved. After sitting for a month or so I fired it up and its back to running rough then stalling.
I bought a Vgate ELM327 connector and downloaded FORScan on my laptop. (I'm still not sure what I'm doing). These are the stored codes P1281, P0475, P1316, P0478, P0470, P1211. I cleared all the codes. I did a buzz test cold and the Injectors all sounded the same.
I monitored the truck while running (rough) the IPR is staying around19.92%, ICP is 701.4psi. After 5 seconds the ICP starts to climb and so does the IPR, at 12 seconds the IPR is 37.11 and ICP is 1835.1 psi the it stalls. The fuel pw,ms is around 2.50-3.0 until before it stalls, then its 1.66. The only codes that come up are P0475, P0470, B1473.
View 14 Replies
