I have a 99 gmc jimmy. Head lights and tails lights work. But not the Hazard and or turn signals. I checked fuses. I'm thinking it might be the plug under the ash tray. But I don't want to pull off the dash to find out it isn't that.
View 4 RepliesI was turning left in my 01 Excursion and I think I hit the turn signal while doing so and tripped something. Now I have no turn signals and no brake lights. Headlights and tail lights work fine. I checked a couple of fuses under the hood that I believe are for turn signals, according to my manual they are fuses #20 and 22. They aren't getting any power, but the fuses themselves are fine. Is there another fuse somewhere to check? Or something else entirely?
View 12 RepliesI have a f 550 that blew out starter cyl on inner fender.and starter, replaced both. Now I have no brake lights or 4 ways and no turn signals....
View 4 RepliesI just got a 2000 F350 cc drw 7.3l.
I did search but have had no luck. My turn signals do not work, unless my foot is on the brake pedal my green arrow indicator wont even turn on. When they do my bulbs work but don't cycle so I know all the bulbs are good as I had my wife check all four corners when I got them to come on for a split second. I have tried replacing the MFS and the turn signal relay under the radio in the dash.... When I do turn on my blinkers I can hear the relay click once but that is it, no more.
I tried checking the wiring in the column and tilting the column to its extremes while trying to engage the turn signals. Also, if I unplug the brake light switch then I do not get an arrow on the IC to light up so I am guessing the power flows through that switch. I don't have a chilton manual yet and the owners manual was not in the truck. I did check fuse 23 ?
I'm having problems with my front marker lights. The turn signals work but when I turn on the parking lights or headlights they don't work. They only work with the turn signals. And I can't get the front side marker lights to come on. I've tried everything...
View 2 Replies2005 F350 Super Duty. I have no brake lights turn signals or hazards. dealer suggested the multiswitch but changed it and still not working?
View 2 RepliesComing back from a trip I got a e-brake light show up on the dash then noticed the signals stopped working and the heated seats no longer turn on. I scanned it with my AE and got a brake fluid sensor error come up but nothing about the signals .... is this a common problem or is there a connection between all this? 2003 F350 6.0L .....
View 2 RepliesMy sons 2006 F350 brake lights and rear turn signals quit working. When the headlights are on, all the lights operate but the rear turn signals and brake lights do not nor do the emergency flashers. The front signals work but flash very rapidly. Although I'm not an auto electrician, I'm fairly mechanically inclined but the fact that the front signals work, the rear don't and all lights work as lights, just not as turn signals or brake lights.
View 4 RepliesI have a 2006 F250 Superduty 4x4 that the brake lights hazards and turn signals have stopped working in the rear.. The middle cab brake light does not work either.. The running lights do work as well as the turn signal and all lights in the front.. I also checked the trailer plugs and both work for running brake and signal lights.. I have checked all fuses under the hood as well under the dash with a test light and i have nothing blown.. I have replaced the Brake switch as well as the flasher module under the dash and picked up a new multifunction switch (Turn signal/hazard) and that didn't work either.. I'm stumped at this point.. I have not checked the bulbs yet but wouldn't think they would all blow at the same time.. (will do this next)..
View 3 RepliesEvery time I step on the brakes, there is a bright spark in fuse #13. My brake lights, turn signals and hazards don't work. At this point my truck isn't drivable.
According to the owner's manual in my truck, says circuit #13 is for "stop lamps, CHMSL/hazard, trailer tow stop lamp, and speed control."
I'm assuming that the hazard part covers the turn signals as well, but I know the cruise control works even when the fuse is blown. I used it last night on the way home (this was before I realized I didn't have brake lights).
So I know I have a short somewhere. The only mods I've done to the lights are aftermarket headlights, but if the fuse only gets blown when I step on the brakes, I don't see what that would have to do with it. Also, the lights have been installed and working for about a month before this started. The only thing that I did around the same time was install the gauges. I ran the power to them from #5, the customer access circuit.
Are there any other "common" areas for this to happen? I already removed the rear brake lights and it didn't work. I am quickly running out of 20A mini fuses.
I was adding some more running lights today and tried to tie in to the front running/turn signal light. Next thing I know I hear a pop and now no turn signals, hazards or brake lights on my 99 F250 SD V10. My 3rd (center) brake light does work though when I press the brake, it's just the tail brake lights that dont work.
I can't find a blown fuse for the turn signals or brake lights (not really sure which fuse box it's in since the manual doesn't tell me what fuse is what)
I however did find what I'm guessing are the flashers behind the radio. What might have went wrong where before I start dumping money in to flashers and relays.
The next question is, can I jump in to the marker/turn signals and add another single LED light to them off the front? If I can which color wire does what?
I have a 1995 Ford f250 Powerstroke and i do not have turn signals, rear running lights, brake lights or reverse lights. i checked the fuses and they seem to be good but i dont want to tear everything out to check the harness if it could be a bad ground. any insight?
View 1 RepliesRecently, I lost function of brake lights, turn signals, and hazard flashers. All happened at the same time. Some threads discuss flasher relays, short steering column wiring (position of steering wheel), and fuse failures.
I checked #18 fuse and a few others. All had continuity. I assumed my bulbs were all good. My hazard push-pull switch did not feel right. There didn't seem to be engagement. At this point, there was a good chance that the multi-function column switch had failed so I decided to try replacing it. I'm happy to report that this switch was the cause of all the light function failures and now, all is well again.
Removal is done by prying the key lock switch cover off,, removing three 1" Philips head screws that attach the lower column shield to the upper shield. At that point the upper shield can be completely removed. The lower shield was not totally removed because the tilt lever was left on. The switch is attached to the column with two 3/4" Torx 20 fasteners. The upper is easily accessible and the lower fastener can be removed by pulling the lower column shield down so access can be achieved. The two wiring harnesses have a conventional harness lock to depress and the connectors pull outward from the switch. Installation is the reverse of removal, noting the dowel locator and small plastic dowel on the lower shield.
When I pull down on the turn signal to signal a left turn, my emergency lights turn on (both left and right blinkers). I tried to figure out whats going on but don't understand what to check/replace. I did notice though that if I don't pull all the way down on the turn signal then the left turn light blinks normally, but as soon as I pull down to activate it to blink on its own, it triggers both blinkers at the same time.
View 11 RepliesI found out last night that all 3 of my brake lights are out. However, my tail lights work, and my turn-signals work. So obviously its not a big wiring deal. I was looking for the brake switch but i don't know where its at because i looked underneath. What fuse is the brake lights cause my manual doesn't have it listed. I drive a 04 Elantra GLS.
View 6 RepliesI have a '97 AWD and my brake light, turn signals and emergency flasher have stopped working. I've checked all the bulbs, checked all the fuses (under the dash) replaced the flasher just in front of the fuse box...nothing. All the running lights work, and the 3rd brake light above the rear door window works.
View 3 RepliesI have a 1999 GMC Jimmy 4.3 Vortec. When you turn the key it doesn't roll over, all I can hear is a click in the passenger kick panel. I have checked the starter solenoid with a jumper and it is fine. After a ton of checking with a multimeter and swapping fuses and relays I found something- when I remove the 40A "ign A" fuse in the fuse panel under the hood and plug it back in, I turn the key and it fires right up and stays running. However if I shut it off and try to start a second time, it doesn't roll over and begins clicking in kick panel again.
View 8 RepliesRecently my Infiniti G20's turn signals and hazard lights stopped working. I replaced the flasher relay and turn signal switch but it did not solve the problem. Here is the kicker or clue. The lights flash when locking or unlocking the car with the remote FOB.
View 7 RepliesIs there a way to make the parking lights (on the boot) to work with turn signals and brakes? I want the turn signal action to look like this : [URL] .....
BTW, I tried searching on this topic but I found nothing. I'm planning to buy this kit - [URL] .....
I have a set of retros with dual turns. I was wondering how to go about wiring up the turns as my city lights (i have a euro switch). Is there a diagram of the wiring anywhere?
View 3 RepliesTurn signal lights into parking/turn signals (6th gen 2011 Camry LE)? I replaced my parking lights with a bright led that matches my headlights, but I would like my turn signals to be on when my parking lights are on.
For some reason I thought they turned on with the parking lights (my other cars do), so I bought some switchback led's and after I installed them I realized that my turn signals don't come on with the parking lights. Is this something I can do by swapping out a relay or with some minor wiring changes?
I am planning on getting the relay below to stop the hyper-flashing and am curious if it would do anything else, common sense makes be believe it will not since the lights don't currently don't turn on, but I am not 100% sure. Also, is 1 relay better than another? They all seem to be the same with the exception of some have controls to adjust the flash speed.
[URL] ....