2001 gmc 2500hd 8.1l.... Check engine light is on. Code reads CAM Sensor, however I changed out the sensor myself and it still wont go away. My truck wont start on the first two-three times and it will back fire occasionally. What to do next?
View 8 RepliesMy 2001 f250 on occasion will roll a very uncomfortable distance when I put it in park. Not all the time, but enough to concern me. It will roll a good 12-18" before the park rod or what have you engages. Doesn't seem to be affected by grade. Matter if fact it has always done it on just slight grades. Nothing like a boat ramp. It rolls enough that if someone had been front or back it would have bumped them.
View 1 RepliesI have been having odd problems with my truck for several weeks now and what the problem may be. Occasionally the truck will not start. This happens after it has been run for an errand or to church. The truck turns over but no ignition. Sometimes if I pump the gas pedal very quickly I can get it to start. Other times I have to sit and wait about 5 minutes. I have gotten the following two error codes - P1506=Cylinder Head Temp Sensor and P1299=Idle Air Control Overspeed Error. For two days the "check engine" light was on, but now it has gone out. I have searched for an answer to this problem on these boards and one possibility may be a vacuum leak. Is this the most likely? 1998 Triton 4.6 ....
View 3 RepliesSo a few weeks back, i went to the store after work, came out and my truck just cranked and cranked but wouldn't turn over. I simply turned the key off and back on, waited for the WTS light to go out and she started up. I just blew it off, thinking i didn't wait long enough to start it.
Then, later that week i come out of a restaurant and it cranks and cranks but doesn't start. i tried turning the key off and on, waiting 30 seconds between em and still nothing. Then a few minutes later, i try again and she fires up, no problems and runs like a champ.
Well 2 fridays ago, I go out with some buddies, go to leave and it happens again. Cranks and cranks, but not starting. I got a ride to my place, grabbed a fuel filter, thinking maybe its clogged, it's been awhile since i changed it. I got back to my truck, and it started up fine, without changing the filter.
Then last night as i am out of town, 10 hours away from home it happens again. And i kept trying and trying and trying but it never wanted to start. I was about to submit my payment for the Uber back to my hotel when i decide to try it again and it fired right up.
Now I'm kind of afraid to drive anywhere and shut off my truck in fear of being stranded. What could be causing this? I've looked every where and havent found someone with the exact same problem, usually when i find a thread on turning over but not starting, the truck dies once it runs as well. Mine doesn't. when it starts, she runs great.
No smoke coming out the tail pipe when cranking.
WTS light comes on and off as it should.
Tach does not move, and it won't because it's a 2002.
Where to start, would the CPS cause it to act this way? It only seems to do it when the engine is warm.
I bought my 2003 F-150 XL (4.2L V6, 2WD, had 165k miles when purchased, 170k now, battery is a Napa brand manufactured in April 2012) in June 2012. A few weeks after I got it, I started having some weird issues. The check engine light came on and I went and had the codes read at Advance Auto. They were P0171 and P0174, lean bank one and lean bank two. The vacuum leak causing these codes isn't the issue I'm dealing with, it is the electrical problem.
The truck will occasionally flash every light on the dash (service engine soon, low fuel, oil, coolant temperature, seat belt, door ajar, and a couple others if I remember correctly) when I turn the key to power on the electronics. The first time I turn the key all the way to crank the truck up, it cranks fine, starts up, and dies within 3-4 seconds. The second time, it does the same thing. Third time, it just cranks and cranks, but will not start. After cranking and not starting a few times, the truck basically just clicks because the battery is run down.
This problem has happened randomly since June. It might be six weeks, one week, or only a few days between occurrences. The last two times it did it, I took the battery out of the truck, put it on a 6 amp charger overnight (about 8 hours), put it back in the truck, and it still wouldn't start, lights still flashing, etc. I gave it about 2-3 hours and both times the truck would start strongly and without incident, and the service engine soon light was off.
It rained here a LOT this summer, so I figured it might have something to do with driving through standing water at various speeds. The problem seems loosely associated with rainy weather (it rained last Saturday and I had to drive approximately 10-12 miles in it), but now it has started something new.
Yesterday afternoon, I tried to start the truck and it did the above described problem. I took the battery off and put it on a 10 amp charger for about six hours yesterday and left it disconnected overnight. Reconnected it this morning, gave it a couple of hours, still nothing. I remembered one time a while back that hitting the odometer reset button made the dash lights stop flashing. I held down the reset button and everything stayed lit up, but stopped flashing. Turned the key with the reset button held down and the truck started right up, but the dash kept flashing.
Turned it off, tried starting it without holding down the odometer reset, would crank, but not start. Tried starting it while holding down the odometer reset again, started right up. When I turned it off and tried it a third time, it just cranked for about six seconds before I gave up. This time, the oil, coolant temperature, battery, and service engine soon lights stayed lit (not flashing, they were solid) and the truck refused to start anymore.
Before it did the odometer reset BS I thought maybe I could figure it out because while it was a ghost of a problem that randomly came and went, it was always the same issue. Now I'm COMPLETELY lost.
so my 96 dodge dakota has been acting up a lot lately. I can barely drive in town let alone on the highway. when I drive, keep in mind its random most of the time, my truck will start jumping and then lose power. when I try to power thru it my truck will backfire and then shut off. once I try to start again it floods the engine. most of the time it will do this going up a hill or when it has to get above 3000 rpm. I don't know what's causing it. I replaced the throttle body fuel injection sensor and tranny filter but I figure its a fuel problem.
View 9 RepliesMy GF has a 2002 Elantra, and recently, she's had a remote start kit put in her car. Previously, though, we were moving something in/out of her car and broke the shift knob and the rod became bent, so we had to bend the rod back to be able to put the car back into park. (The car is an auto).
Recently, she's had a couple rough/no starts from her car. There have been a few times where she would come over to my house and the car would not restart soon after she turns off the ignition. However, the car will start rough about 3 hours later and run perfectly fine once it cranks. This doesn't happen often, but enough to be troublesome.
The problem with this though is the fact that sometimes it starts and sometimes it doesn't, and it runs PERFECTLY fine. The lights are not dimming, the battery is not dying, the car has not required to be jumped. While having these problems we drove the car around for about 5-6 hours and it was perfectly fine. Her dad thinks it's the alternator, but the battery hasn't been losing any charge and the battery hasn't been dying. There has been one time where her father moved the shifter up and down and put it back into park and the car started just fine. Could this be related to the shifter, and how the car isn't reading that's it's fully in park to relay ignition? Her dad said he tested the alternator and it was "bad," but like I said, if the alternator was bad, her battery would be losing charge, and that is definitely not the case.
2001 F250 5.4 ... I'm losing my mind chasing a Gremlin. I've been having mostly intermittent starting issues with my truck. I've had the truck for a little over a year, after someone totaled my previous one.
It occasionally wouldn't start on the first attempt, but it got really bad in the last couple weeks.
I first thought it was a faulty inertia switch or wiring in that vicinity, as at one point after manually tripping and resetting the cutoff switch it would start, UNTIL I put the trim panel back. At this point I think that may have been a coincidence.
I eventually probed the switch and it tests as it should electrically.
I put in a new fuel filter and things were fine for several days, but it acted up again. That time was last Saturday. Got it to start and all was good until tonight. Now it won't go, and I've tried so many times that I can see the battery power is dropping.
Last Saturday I pulled the relays from behind the radio and cleaned 'em up real nice. Also, just to check another variable I swapped the two that matched.
I'm about ready to change the fuel pump, but I've heard so many people say they did that but the problem was something else. Not only will it costs hundreds of dollars, its cold out and we'll have to drop the tank in the driveway.
In addition to the relay, inertia switch and fuse, I have found some mention of faulty fuel pressure regulators causing issues. I'll pry the vacuum line off in the morning to see if I can detect fuel residue on the vacuum side. (There is some noticeable corrosion on the fuel rail in that area).
I REALLY want to make sure I rule everything else out before spending hours under the truck in freezing weather dropping the tank and changing the sending unit out.
On key-on there is a noise from the gas tank, but someone else listening described it as a click but no whirring.
I do hear the relay clicking behind the radio. (Also, I pulled them again tonight and put a meter to them. With 12V on the primary side, they click and the other side shows continuity on diode check, and about .2 Ohm on resistance mode.)
I went through a lot of trouble to get my spare out looking for the fuel control module before finding out my truck is about 3 years too old to have one too. What else to check?
I just acquired a 01 wolfsburg jetta 1.8t and first time vw owner.
I just got the car and found that all the pcv ventilation hoses were crumbling and broken down. I replaced everything under the intake up to the y at the valve cover. All was in stock at the dealer was the oil cooler elbow, tee and pcv valve. From there, i made my own hoses using 3/4 hose and couplers.
Before this, it ran fine but sometimes at idle the idle would jump up and down but not die. I also had a couple codes, can't remember what the number was. One was O2 bank 1 sensor 1 lean and i think the other was O2 related.
Now, after trying to fix the leaks. CE light went out but idle still does the same but my boost improved from like 5psi to like 9psi wot. That's not an issue but coming home tonight when i went to second, it felt like it was dragging or not wanting to accelerate or accelerate and like stall for a second. If you blip the throttle it back fires while in second when its doing this.
Only mod on the car i know of is it has a forge DV/blowoff i guess is the correct name. It can be used as a dv or both.
2003 Elantra gt 90,0000 miles manual transmission. Rough idle under 1000 rpm it smooths out completely above 1000 rpm.
Also the engine makes a ticking noise from a cold start up. It stops making the ticking noise after 1500rpm or when the engine warms up.
Occasionally the car has a sputtering backfire. This happens when I park the car after being on the highway.
Replaced the plugs, wires, and the pcv valve. Dropped the oil pan and it and the oil pump pick up screen were clean.
The only check engine light to come on was for the speed sensor. It has since gone out on it's own.
I have A 2001 Santa Fe. The check engine light came on about 3 weeks ago and the car was still running fine up until the last few days it felt a little sluggish. Today I got a little muffled backfire noise. It was like a putting noise if I pushed on the gas to hard to speed up. The car has 95,000 miles on it.The car starts up with no problems and doesn't stall. Its A 6 cylinder All wheel drive vehicle.
View 10 RepliesI have a problem with my 01 santa fe. When I start it the engine runs rough and when u try to give it gas it pops or backfire through throttle body and air intake tube? Checked the timing belt its ok hasnt slipped.so im stuck at this point.
View 8 RepliesI have been having this odd issue where my car will back fire after a cold start. It only happens when getting out of first gear and going into second while driving (it happens as soon as I press the clutch pedal all the way in, and stops as soon as the clutch pedal is back out). It doesn't happen all the time, just every now and then. My only explanation of this would be that I live a mile above sea level (I looked at the FAQs and know that the car will act like its about to die on a cold start, yet it doesn't). So with my only "explanation" of this phenomenon being that I live a mile above sea level and the engine running rich for a few minutes after start up. My car is stock with the exception of the flapper mod.
Pics for Clicks ......
So, I was driving down the road one day at like 50mph or so and had the loudest backfire I've ever heard. As I was putting my car on the dolly to tow home I heard a bunch of rattling and thought maybe it was a rod bearing or something. I pulled the oil pan and found chunks of my upper chain guide (rod bearings were fine).
I replaced the chain guide and checked the timing hoping it would fix the problem, but it didn't. The rattling was gone but I was only running on 3 cylinders. Did a compression check and had 0 compression in Cyl5 and about 60-70 in Cyl2. I don't remember exactly what the compression was for the other cylinders since it was a while ago.
Started thinking it was bent valves, so I just recently pulled the head off to check them. They all looked like they were seating properly and none looked bent from what I could tell. I'm about to try to put some compressed air through it to see if the valves are leaking anywhere. the plugs, wires, and coilpack are all functioning properly.
My silverado no longer starts and the fuel gauge no longer reads. so far figured out that there is no power to the fuel pump and sending unit. Looking for an engine wiring diagram for this truck with the 6.0 engine?
View 14 RepliesRecently my 2001 F150 4x4 5.4 truck has been misbehaving by being difficult to start at random times. The engine will turn over with however will not fire. After some time, I am able to get it to fire. When this happens the truck start normally for the rest of the day and maybe several days. Around the same time, error codes for a variety of sensors would occur. This problem was traced to a broken PCM connection. When this problem does materialize, no error codes are generated. After some time in repair shop, a probable cause could not be found.
View 9 RepliesSo I just bought a 2001 F-150. It has the 4.6 v8 it's a 4x4 automatic. Sometimes i'll go to start it in park but nothing will happen. But if I put it in neutral. It'll start right up.
View 7 RepliesI have a 2001 ford F150 with a 5.4 2WD, with a starting problem. Last Friday I went to leave work the truck cranked but did not start, turned the key off and tried again same thing, on the third try it started. Drove it home 30 miles with one stop on the way, restarted just fine. At home in the driveway I restarted it 5 times without a problem so I was thinking it was just a glitch. Did not drive the truck all weekend thinking the problem was fixed.
Monday morning leave for work and everything was fine, went to start the truck in the afternoon and the same problem as listed above (3 or 4 tries and it started). It home again in the driveway restarts every time. I do not have any check engine light on but I thought I would still plug in my code reader NO CODE. Where to start troubling shooting this problem?
2001 f150 4x4 5.4 205k ... This truck is not my daily driver but I use it about once or twice a week. Last night I drove it to the store and it ran great. As good as ever.
This morning it won't start. It cranks and the battery is strong but no bang. It was cold. Just below freezing for the first time this year. No blown fuses where would you start?
So I have a 2001 f250 7.3l and on my way to work yesterday while driving down a hill I switched my ts 6 switch to 140 and it immediately stalled, so I pulled over and restarted the truck and it started up fine and I drove the rest of the way to work, I go to start it after work and it won't start, it just cranks and cranks and cranks, occasionally it'll fire and I got it to start and was able to rev it for about 30 seconds but then it died, disconnect the 6 position switch from the idm and tried but still nothing.
So today I replaced the ipr valve, got everything back together still won't start maybe a little worse now, I know it's getting fuel cause there's pressure in the bowl when I try to take it off, there's a new icp valve, cps, new fuel filter and new sending unit, the hpop is topped off. Also I noticed when I went to change the ipr the wires on the plug were bare and touching so I addressed that, I don't know what else it could be?
i have a 01 Ford F-350 7.3L quite and won't start I have replaced the ipr valve and sensor and the crank sensor and the truck still won't start...
View 1 Replies