Ford - Explorer :: 2002 4.6 L - Replace Engine - Need VIN Number For Match?
Dec 29, 2014
I just drained 3 gallons of coffee colored goo from my wifes 02 mountaineer crank case. looking for a motor I am getting migraines because the salvage guys say there were alot of changes from year to year in the early 4.6L that are not interchangeable. decypher this BS. What is the simplest way to match up what I need? Vin Number? is there a code some where? or do I need to track down an exact replica of my wifes truck?
View 1 Replies
Advertisement
Thats what my mechanic told me about my 2002 exploder sport trac with 4.0. I started another thread here a while back about my truck having a bad miss, turns out it has a broken valve spring. He said the engine must be removed to do the job as its on the #1 cylinder which happens to be on the passenger side and the cam chain drive is on the back of the block.
He said my choices are: Remove the engine and just replace the spring, which may or may not effect a repair as theres no way to know if the valve made contact with the piston. Remove the head and send it off to a machine shop for repair/inspection. Or, remove both the heads, one for repair and inspection, the other just for inspection, and then put the whole mess back together.
Whats the best option here? I'm not exactly made of money, and, I'm still licking my wounds about having such a mechanical disaster take place on a vehicle that up until this point, I absolutely loved and has only 90,000 miles on the clock.
View 2 Replies
My VIN inside the door is scratched enough that the State can't verify it. They need two locations to match the VIN otherwise the vehicle must be scheduled for a "level 3" vin inspection hundreds of miles away. Well I tried to find one on the engine where the DMV can do a "level 2" vin inspection but I can't find it. Where other vin's are on my 2002 Ford 450. Mine is a flat bed.
View 4 Replies
I've been looking online to see how often you need to replace the oxygen sensor for the 3rd gen Prius. I can't find anything online. How often you replace these? Would it be around 100,000 miles or more because it's a hybrid? Also how many are there? I've heard there is 2 and some say there's 4.
View 2 Replies
Ford Explorer Sport 2000, Number 1 spark plug has miss firing already replaced spark plugs wires and coil pack what more can i do to get spark from number 1 to spark and took garden hose to listen to injectors clicking when running. any other part for spark.
View 1 Replies
On my V8 02 XLT Explorer the engine is running rough like it's missing.
I think a coil may have gone bad,,found a LOT of anti-freeze down in the spark plug hole.
Have replaced the intake but now need to fix the roughness.
Is there any easy way to check each coil? Or should I be checing something else?
View 2 Replies
I have 02 Limited 4.6 with 128k and upon startup there's no noise (sometimes misfire, due to oil in plug wells, gonna change the intake mani and coils soon). Shortly after it warms up - 5 minutes or so there is a constant ticking at idle...I can't really tell if its there upon acceleration as I can't notice it with the window open when I'm driving, but as soon as I slow down and/or idle I hear it again.
If I let the car sit for a few hours, or while I'm at work, it starts up perfectly fine, no noise.
I tried the long screw driver trick - putting it to different parts of the engine and placing my ear over the handle, and didn't really notice anything different from any part of the engine. I had it up on my lift, and it almost sounded like it was coming from the rear - near the tranny, but what the hell would tick back there? and how do I diagnose that?
I dropped the oil pan when I first got it and there was a very little amount of black rubbery stuff - presuming its timing chain guide/tensioner related, but no chunks, not really any metallic shimmer in the oil, so I guess it could be that, I'm gonna pop the valve cover off and inspect - but like I said, didn't notice anything with the screwdriver trick....I'm at a loss
View 2 Replies
I have a 2002 Explorer with 147K that makes a chirping sound when I start it and the engine is cold. So far I have replaced the serpentine tension-er and the water pump. After about 10 minutes of running the noise stops. With the belt off the idler pulley spins freely. It does have the original power steering pump.
View 3 Replies
Used it to put my spare on after getting a flat. Now that my regular tire is fixed, my spare needs to go back on wench. HOWEVER, the guy at the tire place tried and tried and couldn't get the wench to move or lift the spare. I need a new wench. How to do this?
View 1 Replies
I think it's possessed! My sisters vehicle, a 2002 Explorer with a 4.0 V-6, automatic, 2 wheel drive will just shut off. At first it acted like it would vapor lock. But it would start right away. then the a while later, (several months), it got where it would drop rpms and the engine shudders, sometimes not dying.
When this first started, the throttle body was cleaned, a new air filter installed, fuel pressure checked. Everything checked out and for a few days it ran fine. Then it started all over again. There has never been a code thrown. All of this goes on only when the ambient temp is above 70 deg.'s. below 70 deg.'s it runs perfect.
Last week it went to the mechanic again and a new crank speed sensor, fuel pump, and diagnostic done. He could not find anything wrong any where. Took it for a test drive and it dyed on the mechanic. Still no codes. What the problem might be? Every Mechanic that has looked at it has gave up, one even saying, " it's possessed."
View 14 Replies
How to reset the Anti Theft on my explorer? The light is flashing fast and the engine won't start. Without the anti theft being reset the truck won't start. Been checking around to find an answer but can't find one...
View 7 Replies
The 2003 Ex. Made it back home last week after a couple years at college. .. registration sticker expired last June! Drivers side mirror "taped" on. Rear bumper cover torn in half w/ a few screws holding it on.
Busted out foglight & small tear in bumper cover above it.
Brake light on - noticed fluid low & cap not seated correctly. One of the tabs that hold the cap in place is broken... new reservoir under $20 at rockauto. Looking for a write up or better to replace entire master cylinder?
View 3 Replies
2002 ford sport trac.I have been having an ongoing issue that started with the engine cranking but would not turn over until an hour passed. After replacing multiple parts (cam shaft sensor, crankshaft sensor, ignition pack) I am now down to poor fuel economy as the last of the issues (roughly 12 in the city and 15 highway). I was told the issue may be the engine coolant temperature sensor going bad so I decided to replace it. I found this was very difficult due to it being a plug and locking pin design and in a very tight spot in the engine.
I tried to purchase a replacement and the parts store kept trying to insist on selling me a part with threading. I finally found someone that figured out the issue and found the part for the 2001 sport trac had the same plug style with clip that did fit but was shaped a little different on the sensor end which I assume was due to being aftermarket. I noticed that there were two plugs side by side and the one easiest to access was on the left and I was told the one on the right was the sensor that gave the temperature reading to the gauge.
After installing the engine coolant temperature sensor I found the temperature gauge on the dash now will not respond and is sitting below the cold end of the gauge completely off. Is it possible this is because the part was for a 2001? Is the sensor on the left (passenger side) the engine coolant sensor?I would hate to put the old sensor back in just to test if that's the issue due how difficult it was to put that locking pin back on. What to check that could resolve the gauge issue before pulling this sensor back out?
View 3 Replies
Got 2006 Explorer back fron trans rebuild and probably unrelated but started getting P1405 (Large vacuum leak) and alternating "replace gas cap" errors. When I installed a new gas cap, error went from large vacuum leak -which I checked for on engine and found none using smoke test- to loose gas cap. So next, I changed the emission system valve which is right up front on rt. side of engine looking into engine bay. Now, error has returned to large vacuum leak. So new gas cap and valve. Error does not come back immediately after clearing. Takes about a week and then either get SES light and large vacuum leak error or just picture of gas cap on dash error. Note that when I remove gas cap, I no longer hear the "whooosh" of releasing a vacuum. Assume now it is in back by spare tire where I need to be looking. I note on emission valve that there is a schrader valve for testing vacuum....
View 6 Replies
I am in the middle of replacing the timing chains on my 1998 4.0L SOHC 4x4 Explorer. I was going to ignore the balance shaft chain but a piece of the broken jackshaft chain tensioner broke the balance shaft chain tensioner too. Now I have to pull the upper pan/ladder frame.
Of course, the manual says I have to pull the motor to remove the upper pan/ladder frame on a 4x4 but I have heard there may be a way around this. How to avoid pulling the motor and still be able to replace the balance shaft chain tensioner?
View 9 Replies
I have a 2002 Camry V6 US model. I need to replace the Oxygen Sensor that is on the front (beginning) of the Front Exhaust Pipe Assy, just before the other sensor which is on the curved part of the front exhaust.
When looking at the DENSO website, it lists two sensors BEFORE the catalytic convertor and two AFTER it. I don't see ANY sensors after the convertor(s), nor does the Toyota Camry shop service manual show them.
Are there only two or are there more than two? Also, what is bank 1 and bank 2? I'm assuming bank 1 is the front cylinders and bank two are the rear (towards the windshield).
View 3 Replies
I just bought a 2002 Grand AM, and the radio displays 'LOCKED'.
I tried: p { margin-bottom: 0.08in; }
Looking at the face of your GM Delco radio, hold down the preset buttons 1 & 4 OR 2 & 3 (Depending on year and model) for approximately 10 seconds or until a set of 2 or 3 numbers comes up on the display. Write the numbers down. But the radio continues to display 'LOCKED', and no numbers appear.
View 2 Replies
So a line of panic stops on the highway last night and I lost - stopping an 8000lb rig compared to hondas, nissans, etc. Anyway I just kissed the corner of a nissan xterra and dented the steel part of my front bumper below the driver headlight. Nothing else. It is a 2002 all black limited.
I am wondering about fixing vs. buying a new bumper. A new one from the dealer is 436 and then needs to be painted.
View 14 Replies
With an AD2 and no HFCM, need to have a part number for just the top of engine filter? All I can find (Motorcraft, AMSOIL, Racor) are the dual filter kits.
View 4 Replies
I bought a used 2006 F150 Lariat 4x4 (5.4L) and discovered that the oil filter and filter housing did not match stock. All web searches return the fram filter ph2 but the truck had the equivalent of ph10575. It was the right filter for the housing so it's not a case of someone putting the wrong filter on the truck. The ph10575 filter is for model years 2010 - 2013. Should I start investigating whether the engine had been replaced or is this normal?
View 6 Replies
Over the last few days I have read several threads about heaters not working and blend door replacement. My '02 4.6 F-150 has 250k+ miles and I've always done regular maintenance on it. With the cold front moving in I've noticed that the heater is not blowing hot air. I flushed the radiator and flushed the heater core several times to make sure the core was not clogged. I also replaced the upper radiator hose because of the "crunchy" sound when squeezed. I also replaced the thermostat. Still, the heater is not blowing hot. I assume like many others that the blend door needs to be replaced. My question is do I need to replace the door only or the door and the motor (actuator)? I guess I need to test the motor before buying a new one. I saw a video where you remove all the components on the transmission hump and can actually stick you finger in the motor opening to see if the shaft has come apart.
View 8 Replies
