Ford Wiring/Electrical :: Ignition Stuck On With Key Out / Engine Kept Running
Nov 27, 2014
Pulled up to customers home and took key out and engine kept running. Disconnected battery, engine and aux turned off. Then Connected battery and power came on as if the key was in. Then put key in and turned with no change in power or engine trying to turn. Disc battery, put key in first then connected battery and truck started. Last stop took key out as well as disc batt and engine stayed on this time. repeated steps above several times to get back. Looking for narrowing the problem,possible ignition key cylinder, actuator or possible bad circuit.
View 4 Replies
Advertisement
I plan on moving the engine/drivetrain from my 1986 F350 460 to my 1996 F250. I also want to move over the 1986's ignition system with a Duraspark 2 setup.
Although I could just cut in the easiest places to remove the wiring for later reuse I am looking for where to make the cuts, what to take and what to scrap. Alternatively I am also asking if there are aftermarket or OEM replacement sets out there are aren't a ton of money. The current harness in the 1986 has been sprayed with engine oil and cooked for 27 years so I am looking at alternative options if there are any.
View 8 Replies
My turn signals will not work with the engine running. With the engine off they will. With the engine running if I move the ignition like I am going to turn it off they work.. Is it the ignition switch or ign cylinder....
View 5 Replies
Just bought an 04 Super duty with the factory plug 7pin and 4 pin plug. Checked the fuses and finally tracked down the 2 relays under the hood but can't seem to find anything wrong. Everything on the trailer works except for the running lights. Is there another fuse or something I have missed? Trailer works fine on my buddies Duramax and worked fine on my old 97.
View 14 Replies
I have a 1983 E350 RV with a 460 engine. It would appear that many "Mechanics" have altered the wiring in different ways. That being said I think the charging and starting electrics are fairly untouched. My issue is that once it has been running for a while the interior lights start to fluctuate so does the radio display. The AC fan speeds up and slows down and I feel like there is not enough gas being pumped up too due to some coughing and sputtering. When I press the brakes the radio stops playing and if I have the AC on it gets worse. Today I changed the voltage regulator and it made no difference. This vehicle has two batteries, one for starting the van like normal and one to run the coach part. The alternator charges both. I think it must be a bad ground somewhere but not sure where to start.
View 2 Replies
I have a 2007 e350. I installed a battery isolator and I believe I need to run a wire from the ignition circuit to the exciter post on the isolator. I found the Power Distribution Panel under the hood (drivers side) which has a fuse in slot #7 (60 amp Maxi Fuse) listed as Ignition Switch/Accessory Delay. What is the best way to tap into this?
Also, I have 8 gauge wire which I ran from the isolator to the batteries. I am second guessing this now and wondering if I should go with thicker wire?
View 5 Replies
Just got a 66 f100. Some one cut out the ignition. It has a toggle switch that doesn't seem to do anything, turned it to on and used a screwdriver to short the solenoid and it did not crank. I think I counted 9 cut wires in the area of the ignition counting 2 for the toggle. My other 61-66 trucks seem to just have five wires? So I can remove an ignition from one of these parts trucks, but might there be a difference since the gauges are unique to 1966 ?
Started to take the ignition out of my 62 f600 but i hate to cut wires but i must since there is no remnant of an ignition in the 66 f100. If I can match the five wires i should be ok. Just putting a battery in i have headlights, tailights and dash lights. Solenoid and cable to starter look horrible so i bought a new cable. I think i have a good solenoid or two? I didn't even get a spark when i shorted the solenoid with a screwdriver....
View 5 Replies
I have a 77 ford truck with a 351 ,the ignition system keeps shorting out, killing spark. If i replace the starter solenoid, it works for a while, then goes out again. I have replaced 4 solenoids this month. What could be shorting the solenoid out? Had the truck for 8 yrs. now, never had a problem with it till now. It has a mallory dist. it was in when i bought it.
View 7 Replies
I bought a 1952 F1 that is mounted on a 1978 E350 chassis.( 351W )
It has all the 78 wiring installed. When cranking engine, it will not start, unless you release key to run position. You have to get engine turning over, and then quickly release key to start. Checked back of switch, not losing voltage at ignition post while cranking...
View 5 Replies
My 77 F150 Ranger with a 400 in it didn't wanna start up at all. It wouldn't even crank or click like if the battery was dead. Then I tried again this morning and it cranked once then melted a red wired with I think a black or gray tracer, on the ignition. (I put a new solenoid on a couple months back and the positive also melted a bit by the solenoid but didn't pay any attention to it.) I'm just wondering what could be wrong with it to make it do that and how to fix it. Also when I went to put gas in it (it's on a slight hill making it lean to the driver side) it was empty but no fuel would go down the filler neck, then it started to gurgle and spit it out some. I was told it was vapor lock but I thought vapor lock happens when it's hot.
View 3 Replies
Having problems with their door locks attempting to activate when turning the ignition key? If so, how can I correct it or make repairs.
View 4 Replies
here its is i have a 1986 ford f350 6.9 aftermarket turbo set up i was driving it then i went over rail road tracks lost all power to fuse box no headlights no interior lights no ignition power batteries are good so now when i turn key nothing lights up it just killed my whole truck....
View 7 Replies
I wired up a new set of halo projector headlights. I put in load resistors for the led marker/blinker bulbs I purchased. I tested the resistors and after a few minutes I hooked up the halos for the headlights into the running lights. Noticed the resistors were pretty hot, burned my hand. I then accidentally touched the hot marker wire to the ground. That popped the fuse under the hood. But now that same side blinker. Same wires I grounded that also got hot. Blinker stays on, light on dash too. Checked blinker relay it's fine.
View 3 Replies
Moon roof is stuck open can hear motor trying to run on open side od switch but nothing on close...
View 1 Replies
I have a 2004 Ford F-150 lariat with a bit of a problem. My running lights (not sure if correct term, I'm talking about the tail lights' illumination that stays on while you drive at night) are not working. My headlights and parking lights do work, and my brake lights and turning signals also work. I have put in a brand new brake light switch and checked every fuse and relay, but no luck.
View 6 Replies
I have a 1979 f-250 4x4 with a 351m. The problem I am having is my starter keeps running after the truck starts and also after I shut off the key. I didn't get the battery unhooked in time today and it completely melted the lug off on the solenoid, but the other wires were barley warm. What could be causing this problem? The battery is new, the cables are new and the Sol. was new. Maybe the switch or the starter?
View 8 Replies
2006 F-250 SD... I Keep popping the 15A #17 fuse under certain conditions - Driving forward
1. Start with good fuse.
2. Start engine, while in park, turn on parking light...4.8A on circuit. No problems.
3. Put into reverse and drive. down the block around the corner and back up to the house... No problem. 4.8A on circuit.
Put the shifter into drive and - POP - the fuse goes. I never see a jump in the current. 1-5 seconds until fuse goes. While conducting testing, I have had the fuse blow when shifting from reverse to park. Looking at the wiring diagrams, I don't see a common wire that would cause a short when shifting. What I should try next?
View 4 Replies
I have an 01 diesel excursion and last night I came home and when I turned the headlights off the park lights/running lights stayed on. When I turned the switch to park lights on, they got a little brighter? After an hour or so, the lights then went off.
View 14 Replies
So my Honda Civic has been flashing my check engine light, which is telling my my cylinders are misfiring. I checked the ignition coils by removing them while the car was running and cylinder 2 and 3 I can remove and it doesn't change how the car runs. I put a new ignition coil In and that doesn't work so it isn't the ignition coils, what it could be?
View 8 Replies
First off my driver side brake light with stop working. I took it apart to try and find the short. In the process I shorted out all my running lights tail lights and brake lights and turn signals I think also. While I was looking for the short, turn signal wire from my tail light touched the frame and grounded out and that's when all the lights died . My tail lights are some cheap trailer lights without reverse lights. I pulled headlight switch from another Ford truck I have. On the harness connector that connects to the switch which wires should read what when I test with a voltmeter?I checked the fuses in the power distribution box under the hood and they were good. Truck has a flat bed so I don't know if that matters with the wiring, I suspect it's different then a normal bed truck. Wiring on the bed is old, maybe from 94. I am unexperienced with electrical.
View 3 Replies
F250 6.8L .. So Ive read a lot of posts about intermittent cruise control issues. I understand that the most common failure is the brake switch on the master cylinder. My concern is that I am unable to run the cruise control self test I keep reading about. Does this test not work on my model year. I have tried even when the cruise control is working and still the cc light does no come on.
View 2 Replies
