2000 F350 CC DRW 4X4. There's a 3 light bar lamp mounted here that needs replacing. Plastic mounting -Grote 10-7016-01 PCC.- Can't find one. looking for replacement PN? like to have LED.
View 1 RepliesNoticed one of my cab lights was out. Cant imagine replacing it is too bad. But, wheres a good place to find replacement? Probably get 5 for when the rest go.
View 6 RepliesAdding red/white reflective tape to the rear of superduty? Pros, cons, legal etc?
View 14 RepliesI just bought an 05 F250 XLT. I noticed tonight that the rear turn signals and brake lights dont work.
the front turn signals work fine, although they flash fast. I know that usually means a light on its way out. neither taillight flashes though, which puzzles me.
my second issue is that, of the 3 brake lights, only the high mounted light illuminates when I hit the brakes.
I have a 97 F250 HD. Wiring the rear tail lights. When we bought it the had cut off the wires going to both sides of the rear lighting assemblys and I was wondering what wire went to what i have the left turn signal working just can't seem to get the brake/back up light to work on that side and i can't figure out how to get the right side going either.
View 8 RepliesI am wanting to wire my 03 f250 cargo (3rd brake light area) lights to come on when i put my truck in reverse.
View 1 RepliesNeed a wire diagram. I have a connector in the cab that has red,blue,lt green,white wires. It's causing my brake lights not to work. I need a wire diagram that shows were they go. I can't find these wires in my Haynes manual.
View 3 RepliesI am trying to add courtesy lights to the existing reflectors in the front doors of my supercab. I can't find a wiring diagram that shows where to connect the light sockets. 1999 F250 SD...
View 2 Replies'03 E250, standard van with RKE if that's pertinent.............
Looking to replace the on-board 4-way flashing system with Whelen strobes and looking to have the column mounted button be the on/off switch for that power supply. I have a schematic from a '97 E250 (almost identical FWIW) which I can post the pin out, test procedure and EVTM version of the hazard portion of that Multi Function Switch if that's useful.
I know it would be far, far less complicated to control the Whelen via a separate switch but this above reversible mod would be somewhat cool IMHO.
2010 F-250 14,000 miles, gas engine with Knapheide utility bed. Tilt wheel has been kept in the up position from day 1.
The problem:
No rear brake lights.
No high mount brake light.
No rear turn signals.
No rear hazard flashing lights.
All trailer lights work.
All other truck lights work.
Things checked: Fuses all OK. Visual inspection of multi-function switch. Looks clean. Brake switch at brake pedal has power on one wire. Jumpered the other wire-no brake lights.
I need to haul my trailer and am nervous when I see a Savannah, GA metro police car.
Mine is all busted up. All I can find are covers for shorties.
View 6 Repliesmy rear bumper is pretty much eaten up, too.
How difficult is this to replace?
Good source for rear bumpers? Just something stock; don't need anything wild, crazy, lighted, etc.
It's a work/hunting/fishing/hauling truck. That's all.
My new body style f150 , all the rear lights have quit working.whats really odd is at first it was the left signal then the right then everything. All bulbs are good. If I pull the bulb out and test for voltage i get voltage, I replace the bulb and test again.....NOTHING. I took the rear ground off and cleaned it up, test fusses . Don't know what to do from here.
View 7 RepliesMy rear bumper reflector in 2008 Lexus RX350 broke (red plastic part below the tail light). I see replacement part in ebay for around $50. Is it easy to replace? Do we have to remove the bumper?
View 1 RepliesI have a 2013 Accent GLS and I have to replace the rear bumper cover. Any detailed instructions on how to do this?
View 2 RepliesI have no left rear signal or brake lights. The right side works fine and both left/right tail lights work fine, just no left brake or signal. I checked for broken wires and can not find anything. 1992 Ford E50 7.5L.
View 1 RepliesDo I need to remove the rear bumper to replace the rear bumper reflector?
View 8 Replies1991 F250 Supercab Diesel 4X4. I made a mistake while wiring up my trailer lights and ended up grounding out my brake controller, frying it. Along with that, I popped a couple fuses as well (1, 5 and 9 I believe). Replaced all fuses and got my signals (F/R) back at least.
Here's what's NOT working/messed up:
*Brake Lights
*Cruise Control
*Rear ABS light comes on a few minutes after driving.
*Front hazards work, not rear. When I apply the brake, the hazards pause in the on position.
I've tested the brake switch on the brake pedal (Green/Red and Green) and it works properly. So, current is obviously not reaching the rear brake lights.
Another note. The truck is wired with a 7 pin plug in the bed for a goose neck trailer. It also was wired to a 6 pin on the bumper. I replaced the 6 pin with a 7. The signal/brake pins on the plugs (both) and also not receiving power. What's the next thing to check?
Dad borrowed truck and wired 7 pin trailer harness. Lights worked on truck/trailer for use but upon return the turn signals didnt work. Hazards and running and brake lights did work. Replaced TS flasher and Haz flasher. Still no signals. Pulled steering wheel and replaced turn signal cam only, not whole switch. Now no brake lights, no rear hazards or turn signals. Losing my marbles trying to follow schematic and using test light and mulit meter. All bulbs and fuses are good. Running lights and head lights working as well.
View 6 Replies2005 Ranger XL 2.3L 5 speed 2WD 305,000 miles. Alternator has about 100,000 miles on it.
Battery light came on about 0400 and 50 miles into my daily 90 mile drive to work, made it to work. After the truck cooled down for 3 hours and I got time I checked the battery voltage 12.6VDC and started the engine and the system is charging at 14.2VDC with no battery light on (battery light out when cold). Serpentine belt looks good, dry weather.
Other than alternator nearing end of life and being warm is there anything else that may cause battery light to come on.
I just bought an 05 F250 XLT. I noticed tonight that the rear turn signals and brake lights don't work.
The front turn signals work fine, although they flash fast. I know that usually means a light on its way out. neither taillight flashes though, which puzzles me.
My second issue is that, of the 3 brake lights, only the high mounted light illuminates when I hit the brakes.