Ford Wiring/Electrical :: Adding Relays To Fan Controller
Mar 25, 2013
I have a Derale 16749 electric fan controller set up had a fan die, went back to a old set up using a fan shroud I made and sable fans being the controller isn't set up to handle the load from these fans I want to just add relays in. Way the derale is set up to the fan is 12v. constant but the ground is also a 12v. until the switch reaches temp. then becomes a ground. I am not concerned with wiring the low side up on these fans just high side.
View 1 Replies
Advertisement
I'm working on the '73 F250 in my sig. I'm not very skilled when it comes to electrical work and I don't want to hack things. First up is I'm wiring a 7-way trailer connector with brakes. I need to tap into the brake light switch at the pedal, what is the cleanest way to do this? I was thinking of sticking a blade connector in the existing connector or adding a plug pigtail.
Also in the future I will (hopefully) be doing a 3G alternator swap and adding relays to keep my headlights from shutting off. I'm looking for suggestions on a junkyard or aftermarket fuse block that will accommodate the circuit breaker for the trailer brake, the 100 amp fuse for the 3g swap and the relays for the headlights.
View 1 Replies
I just bought a hard to start 1990 F250. Per the board, just replaced all 8 glow plugs with Motorcraft. Still wouldn't start (it turns over but will only start if you use either). I attempted to install a new BWD brand (Borg Warner I believe) glow plug connector relay today...I removed the old no problem, but am unsure what wires to plug where....the only connection that I'm sure about is the blue wire that works the WTS feature...it plugs in easily but I don't know if there are other connections that need to be made or not? All the wires run from the posts and into the bottom of the unit.
View 2 Replies
My truck had power to the Brake Controller until a recent road trip and now there is no power to the controller. All fuses are good. Which circuit the power comes from?
View 4 Replies
What I am trying to do it put in 2 led spot light for added backing up light. What i want to do is have them turn on when put into reverse but also have a switch i can use to turn them on when not in reverse. Just need to know what relay I need and if it even can be done.
I was also thinking of just taping into the wiring harness and adding a wire that goes to the spot lights and another wire that goes to a switch that I could turn on and supply power to the light when not in reverse (I know it will light the revers light also) but is it ok to do that?
View 5 Replies
i have a 96 ranger and want to put cruise control in it. is the wiring there and what other parts do i need to get without going aftermarket.
View 1 Replies
I have an 2015 450 chassis Class C motorhome. The backup camera is integrated into the Pioneer stereo in the dash. The stereo is wired into the headlight switch to automatically dim the display when the lights are turned on. Since I always drive with my headlights turned on, this makes it nearly impossible to see the screen during the daytime.
I learned from Pioneer what to do to disable this feature, but need to install a switch in the circuit to do this. I'm hoping to install a simple on/off toggle switch into the dashboard's existing space. In the picture below, I'm wanting to put the switch into the "round" hole marked Audio Jack.
My question is how do I get the "round plug" out of this hole? And need to know the diameter of the existing hole?
View 4 Replies
a buddy of mine has a 12 F250 that he bought new and is ready to add power locks and windows. I know we can get some aftermarket kits for both but he wants to use the factory door panels and switches from a power setup. I am sure we could use the factory window regulators and panels and just use and aftermarket wiring and flush mount switches. I had figured the wiring might be in the jambs but not in the doors, but when I pulled the trim back, we didn't find any extra wiring going to the rear doors, its a crew.
View 1 Replies
I'm in the process of putting a brake controller and 7 pin plug in on my 98 F150 Super Cab, 4x4, 4.6 L with a auto trans. Got the Tekonsha Voyager hooked up to the existing harness under the dash. I have the 7 pin installed out back and thats where my problem begins. The 7 pin harness came with 3 30amp fuses and 2 relays that need to be placed in the power distribution box under the hood. I can figure out where the fuses go but my manual says nothing about the relays. The relays that are already in the box are for things like fuel pump etc.
View 7 Replies
I removed the rear radio controller from the back of the console and installed a power inverter in its place. It fit great and everything went smoothly. I should have known it was too easy... I now have no sound coming out of the rear speakers. I assume there is a way to jump the wires to allow the speakers to work, but I'd need a wiring diagram. Right now I have the controller hooked up and buried in the console, which I guess is fine. It's just annoying.
View 10 Replies
I am going to be pulling a trailer next week. I bought a raybestos voyager XP controller. I expected it to be plug and play but what I got was four wires. I have heard that there is a plug ready under the dash to plug a controller into directly. I found a gray pigtail with male ends. Is this it? Should I take controller back and get one with the correct plug or is there a harness one can buy or is a stop to my local ford dealer in the future.
View 5 Replies
I just bought a 2000 Excursion limited v10 4x4. I'm going camping this weekend so trying to install my brake controller. I found the plug but noticed these wires dangling. I can't see the back of the harness. I'm afraid the PO may have cut them to install a universal harness. How to recognize them? I don't want to buy a ford specific harness if the wiring has been cut.
View 3 Replies
I am a beginner when it comes to anything involving wiring. I am looking to re-wire all of the wiring coming off of the instrument cluster gauges. Once I have completed all of the wiring on the gauges, I may feel confident to move onto something else. As of rite now, it appears as though my truck is still running on all of the original wiring, and over the past few weeks, I have been having many wiring related issues. I found a schematic that includes the wiring for the gauges that I am going to go off of. I have a couple of questions before I begin.
1.) On the schematic, it shows connectors such as "Connector G" which is moving all of the gauges wires to there locations. Do I need to use a specific Ford connector, or could I purchase a new connector at any hardware store that carries them? As far as I am concerned, connectors do the same thing as all other connectors. (Let you connect and disconnect for easy instrument cluster removal.)
2.) I am not looking to purchase one of those expensive wiring harnesses. I would like to just purchase some wire that I can cut / use myself. What brand / type of wire should I be looking to purchase? I do not care if it is striped / colored as I will use wire tabs to name / label each wire.
Other than that, I feel confident enough to attempt something such as this. Here is the wiring schematic I am going to use.....
View 10 Replies
Any COMPLETE headlight switch wiring diagram? Everything I find online only shows 2-3 wires in each sub connector, nothing with all wires and colors, and what they do. and of course the factory service manuals no longer work on my new computer. the switch and associated wires went up in smoke 2 hours ago, and this truck is my only means of transportation rite now. what i need is headlight wiring with colors so i can temporary hook up a toggle switch to have lights until the new switch and connectors come in next week. I went to pull the switch and connectors out of the parts truck, but of course that does not have fog lights so it uses different switch and connections.
View 14 Replies
I plan on moving the engine/drivetrain from my 1986 F350 460 to my 1996 F250. I also want to move over the 1986's ignition system with a Duraspark 2 setup.
Although I could just cut in the easiest places to remove the wiring for later reuse I am looking for where to make the cuts, what to take and what to scrap. Alternatively I am also asking if there are aftermarket or OEM replacement sets out there are aren't a ton of money. The current harness in the 1986 has been sprayed with engine oil and cooked for 27 years so I am looking at alternative options if there are any.
View 8 Replies
I have a 97 F250 HD. Wiring the rear tail lights. When we bought it the had cut off the wires going to both sides of the rear lighting assemblys and I was wondering what wire went to what i have the left turn signal working just can't seem to get the brake/back up light to work on that side and i can't figure out how to get the right side going either.
View 8 Replies
Looking for a source for a wiring diagram for the 2003/4 f350 instrument cluster, specifically the wiring/connectors to the gauges? A link to a PDF file would be nice. I would like to try and disconnect the PCM control to the transmission temperature and engine temperature and drive the gauges from my own sensors to bypass the non-linear behavior that ford decided was in our best interest. I am NOT interested in installing any more gauges, just want to control the ones already present with my own signals. It is possible that these gauges are all addressable devices on a common bus, instead of individual controls.
View 8 Replies
Just bought an 04 Super duty with the factory plug 7pin and 4 pin plug. Checked the fuses and finally tracked down the 2 relays under the hood but can't seem to find anything wrong. Everything on the trailer works except for the running lights. Is there another fuse or something I have missed? Trailer works fine on my buddies Duramax and worked fine on my old 97.
View 14 Replies
Im installing a set of 04 lariat seats into a 00 truck. I need to know how to hook up the heat. The power part is no problem. What I thought was right which was a separate constant 12v and a switched 12v for the module and ground apparently isnt right. If somebody could ohm out their harness on a 01 truck that would be great. As I have it right now the light on the switch comes on but almost instantly turns off.
View 14 Replies
Looking for a wiring diagram for a F-150 XLT LARIAT 5.8L 4BBL, all the books I have looked at show the wiring for this year with fuel injection and this truck came with a 351W with a Holley 600 4BBL, I have a few wire's in the engine compartment that melted away all the insulation, they are located close to where the harness passes the firewall before the ignition module. Is this a common problem on old models ?. Need a clear copy of the correct diagram for a f-150 1987 with carburetor, how I can get a copy so I can fix this problem before it gets worse.
View 3 Replies
Let me start by saying electrical is something I really have no knowledge of....(never used any kind of an elec meter and don't have one) simple, Pos-grd and fuse, NP. I really don't want to fry something in these expensive new seats w/my normal trial and mostly ERROR!
The 08 (drivers) seat has 4 wires in the input clip.
GRN-RED (heavy gauge)
BLK-PURP (heavy gauge
BLU-RED
BLK-WHT
and my 01 whip out of the floor has a 3 wire setup.
GRN (heavy gauge)
BLK (heavy gauge)
BRN-BLU
I can wire PS side seat from fuse box and ground it NP. It only has a 2 wire set-up in the new seat.
View 1 Replies
