so I recently purchased a 2007 f350 SCSB and my reverse lights don't work. I am trying to trouble shoot the cause... So far I've replaced the bulbs and tested the plugs and im not receiving any power to them... Where to start to look for the problem?
View 3 RepliesI am beginning to think that I need a whole forum dedicated to my trucks wiring issues ... I finally got my reverse lights to work but my newest issue Is that while driving tonight i lost power to my parking lights, my instrument cluster lights, and my heat control lights... everything still works inside (gauges all act properly but they won't light up) and i still have turn signals and brake lights, and headlights. I really don't know where to start with this one. I don't have an owners manual so i can't figure out what fuses to check or what relays to look at. It is a 2007 f350 diesel....
View 9 RepliesWhat I am trying to do it put in 2 led spot light for added backing up light. What i want to do is have them turn on when put into reverse but also have a switch i can use to turn them on when not in reverse. Just need to know what relay I need and if it even can be done.
I was also thinking of just taping into the wiring harness and adding a wire that goes to the spot lights and another wire that goes to a switch that I could turn on and supply power to the light when not in reverse (I know it will light the revers light also) but is it ok to do that?
I don't know if this goes here but I ha a ford f350 king ranch 2006 I got it 5 months ago the fog lights never did work. One of them was burnt out.
I replaced them both today and checked the fuse and they do not come on. I checked the fuse under the dash kick box. What else could be going on here hat I can look into?
I have a 1990 F-350 7.3 lariat crew cab. The tail lights fail to work but all the turn signal and brake lights work. I changed the light switch located to the left of the steering wheel but that didn't solve the problem. all the fuses under the dash appear to be ok to. Is there another fuse for just the tail lights.
View 6 RepliesI bought a set of driving lights to mount at the back of my F250 for extra light when backing up, and hooked them up to Upfitter #4, but they do not work. I mounted them on the hitch, grounded them both on the bed (where a support bracket attaches), ran the power wire up to the front of the truck, and connected it to the white blunt cut pass through wire by the master cylinder. Then inside the cab, I connected the other end of the white pass through wire to the orange/lt. blue wire for upfitter #4. I started the truck, flipped on the #4 switch, and nothing. What I did wrong?
View 5 Replies1998 Expedition EB, the lights on my running boards do not work. Checked online and can not locate the fuse for them, checked the lamps and found one that is burnt out. Here's the dumb question, if one bulb is out will that make the other three not work, something like the Christmas light strings?
View 4 RepliesI am wanting to wire my 03 f250 cargo (3rd brake light area) lights to come on when i put my truck in reverse.
View 1 RepliesI just bought an 05 F250 XLT. I noticed tonight that the rear turn signals and brake lights don't work.
The front turn signals work fine, although they flash fast. I know that usually means a light on its way out. neither taillight flashes though, which puzzles me.
My second issue is that, of the 3 brake lights, only the high mounted light illuminates when I hit the brakes.
2004. Hazards and brake lights work.
View 6 RepliesI have a 97 F250 HD. Wiring the rear tail lights. When we bought it the had cut off the wires going to both sides of the rear lighting assemblys and I was wondering what wire went to what i have the left turn signal working just can't seem to get the brake/back up light to work on that side and i can't figure out how to get the right side going either.
View 8 RepliesJust bought an 04 Super duty with the factory plug 7pin and 4 pin plug. Checked the fuses and finally tracked down the 2 relays under the hood but can't seem to find anything wrong. Everything on the trailer works except for the running lights. Is there another fuse or something I have missed? Trailer works fine on my buddies Duramax and worked fine on my old 97.
View 14 RepliesThe truck is parked in the drive. I noticed when the truck had been parked in the drive I noticed that the tail lights came on and then about 20 seconds later turned off. I checked that the ignition was off, doors were completely closed, etc. It has happened several times. I'm worried the there is an electrical problem that might drain the battery.
View 10 Replies03 F250 Instrument panel does not work. Have checked all fuses with a meter. Have already fixed broken wires from the OD button on shifter handle. and also the alternator is not charging. I need wiring diagram that shows the wires coming out the back of the fuse box so I can see if the fuse holder is burned out......
View 8 RepliesI recenty was having some problems with my 2003 6.0 liter. My FICM connection was not seated all of the way which casued my truck to just die without warning....... AFter I had fixed that, my stereo died. Just dead??? Nothing...EVERYTHING ELSE WORKS???
So, after I had messed with everything I could think of, I thought, OK new DVD/Stereo time.
I checked fuse #32 which was the fuse to my stereo. The fuse is fine...BUT...There's no friggen power to the fuse via my test light. Test light works on other fuse spots so I know i"m not getting power to the fuse #32.
Since I don't have any power to this fuse....WHAT NOW???? How to trouble shoot this problem?
I recently bought a 92 F250 and love it but the blinkers will not work. I have replaced both flashers and the multifunction switch. (the wipers had issues too that were fixed by the switch...) Now what? Im at a loss..
View 7 RepliesMy work truck is an 03 F250 5.3L. My flashers recently stopped working. I turn them on, and they will work anywhere from 5 seconds to a few minutes, then either blink rapidly and shut off, stay solid for a few seconds and shut off, or just shut off. I push the switch off and on again, and the cycle repeats. All my other lights and turn signals work fine with no issues.
This wouldn't be a huge issue, but where I work I need the flashers a lot. The truck has a bar light and siren/pa system wired into it, but not to the lights or anywhere near that. I can't say exactly how it's wired because I didn't install it, but I followed the wires and they don't go under the steering wheel where I would assume the relay and wires for flashers would be.
What sounds like is wrong? I wouldn't think it would be the relay because then I would think that I would be having problems with more than just the flashers. So I'm not sure if there would just be a ground issue or if it's the actual switch that turns on the hazards. Also, there are no lights that are burnt out.
I have a 04 explorer I have been trouble shooting and the master switch works all but the passenger window wont work it at all but all the others work fine, its not the switches replaced both, the passenger window switch will roll the window down but not back up. I checked for power there is power to the switch in the passenger side, the ground is good. I can pull the plug off the motor and hook a jumper ground up and the switch will make it go back up. I have been working in body shops for 40 years and now this is the first one to stump me
View 7 RepliesMy turn signals will not work with the engine running. With the engine off they will. With the engine running if I move the ignition like I am going to turn it off they work.. Is it the ignition switch or ign cylinder....
View 5 RepliesAfter changing my radiator support, my fuel and temperature gauges don't work. I looked to see if everything was plugged in and I don't see anything unplugged. I do know the older trucks used the V-R regulators, but I don't know about this model.
View 2 RepliesI have a 2006 f150. Both front turn signals do not work. I replaced bulbs still nothing. There back signals do work. They blink really fast.
View 4 Replies