Ford Wiring/Electrical :: 2006 F350 - No Power To Fuse Box
Feb 9, 2013
I have a 2006 F350 Diesel. Had one of my employees go out to start the truck yesterday and when I went out I had no electrical power to most of the accessories (gauges, warning lights, power windows, radio, interior lights, turbo charger). It also seems to have no power - could barely make it go up the slight incline into my garage. I have checked all the fuses - they seem fine. Although put a tester on the interior fuse box and I don't have any power to the fuses that run these accessories.
View 10 Replies
Advertisement
2001 F-350 diesel. Out of nowhere, I start the truck and there's no turn signals. Fuse is blown so I replace it. It immediately blows. Tail lights work. No turn signal, brake lights, or hazards. I haven't hooked up a trailer or done anything abnormal recently. Only the #1 fuse (20Amp) is blown. Pulled bulbs and they work fine. Inspected wiring under and near lights. NOTHING! Any way to localize a short?
View 2 Replies
I recenty was having some problems with my 2003 6.0 liter. My FICM connection was not seated all of the way which casued my truck to just die without warning....... AFter I had fixed that, my stereo died. Just dead??? Nothing...EVERYTHING ELSE WORKS???
So, after I had messed with everything I could think of, I thought, OK new DVD/Stereo time.
I checked fuse #32 which was the fuse to my stereo. The fuse is fine...BUT...There's no friggen power to the fuse via my test light. Test light works on other fuse spots so I know i"m not getting power to the fuse #32.
Since I don't have any power to this fuse....WHAT NOW???? How to trouble shoot this problem?
View 7 Replies
here its is i have a 1986 ford f350 6.9 aftermarket turbo set up i was driving it then i went over rail road tracks lost all power to fuse box no headlights no interior lights no ignition power batteries are good so now when i turn key nothing lights up it just killed my whole truck....
View 7 Replies
I was replacing the dome light in my 06 Ford F350. I tested the light and it worked then while screwing it back in, the lights when out and then the radio. I suspect it may be a fuse, but have yet to find the culprit.
View 2 Replies
Looking for a schematic on this truck,standard cab diesel. I have a dead short on exterior lamp fuse. I have no tail lights, running lights, door ajar light is also on.
View 4 Replies
I have a 02 f350 can not get power to a/c compressor have power at high pressure And low pressure can run a hot wire and ground to compressor and it works.
View 1 Replies
I just bought a used F-350 that was being used by a fire department. They did something to the wiring to where most of the electronics won't work unless the key is in the "ON" position. When I open the doors, the dome light doesn't come on, nor does it come on with the IC dimmer switch, when I turn the key either backwards or to the "ACC" position the radio won't work, the headlights DO work but I don't get the warning chime when I open the door with them on.
The flash-to-pass works, as do the hazards and the turn signals (which seems odd -- I don't recall having a car where the turn signals worked without the car being on). With they key on, everything works including the dome light and the door chime. Is there some simple thing they could have done that would make it work this way and is easily reversed?
View 9 Replies
I need to hook up a lamp for my mechanical oil pressure gauge and tested all the fuses, they are either on or on with key in run position, but I found none that went on with the lights, which of course is what I need. So now I guess I start randomly sticking needles in wires under the dash and testing for a possible light switch dependent circuit? Or run a wire through the firewall and tap a wire near a running light? There's got to be an easier way, but my Haynes manual seems useless--one wiring diagram for 1995-2008. I will be forced to run it off a key on circuit which means the lamp will be on anytime I drive, day or night, unless I install a toggle switch--not the best way to do it though.
View 3 Replies
Overdrive fuse keeps blowing. Drive one and 2 shifts fine. 3 and overdrive don't work. Had transmission checked it is fine. Repair shop says it is electrical.
View 1 Replies
I want to add a CB and some flood lights to my pick-up, but am getting tired of hunting for wires that are constant hot or switched hot under the dash. Not to mention the rats nest of wiring that results, and the potential for overloading the factory wiring.
Above is a diagram that I came up with while trying to figure out how to add a constant hot fuse block, and a switched hot (or ACC) fuse block to the truck to clean up the wiring.
Am I using the relays in the right way? (Never used one before)...
View 12 Replies
I have a main tank and an Aux tank with a gauge selector switch. I believe I may have a bad fuse as the indicator has stopped working. Where it is on the fuse block??
1978 Ford F-250
View 1 Replies
I have a 1994 Ford Ranger king cab 4x4 with a three inch lift kit on it . My problem is the fuse is blowing that goes to the fuel pump . It started out blowing the fuse now and then when it was raining . Well I thought it mite be the fuel pump going bad but after I put the new pump in the truck it lasted about a week and started blowing fuses again . I put another fuse in and it go a few days and blow it . Last week on a 100 mile tripe I got almost there and it burned a fuse on the highway . I tried to put another fuse in and it would blow it as soon as I tried to start the truck . Burned five fuses right then . So I had it towed to mothers house and put another fuse in and it cranked up . I looked at the wiring that was not wrapped in that plastic cover stuff and have not found anything yet ...
View 14 Replies
2006 F-250 SD... I Keep popping the 15A #17 fuse under certain conditions - Driving forward
1. Start with good fuse.
2. Start engine, while in park, turn on parking light...4.8A on circuit. No problems.
3. Put into reverse and drive. down the block around the corner and back up to the house... No problem. 4.8A on circuit.
Put the shifter into drive and - POP - the fuse goes. I never see a jump in the current. 1-5 seconds until fuse goes. While conducting testing, I have had the fuse blow when shifting from reverse to park. Looking at the wiring diagrams, I don't see a common wire that would cause a short when shifting. What I should try next?
View 4 Replies
My 2005 4.6L 4x4 screw is blowing the 10amp a/c clutch, 4x4 solenoid fuse whenever i turn the a/c on, at times whenever I turn the defrost on. the fuse does not blow when i turn the key to power (no engine start) but when engine is running fuse will trip. I disconnected elect. Connection at compressor and fuse still blows, also seems like no power or life from compressor.
View 3 Replies
I have a 1994 f150 5.0 engine and automatic transmission. Problem I am having is speedometer, cruise control is not working. Overdrive light is flashing and number 18 fuse keep blowing. horn is still working...
View 1 Replies
I have a 1997 Expedition that every time I replace the #16 fuse it blows when the high beams are on. It seems that it happens only when in drive and accelerating from a stopped position. I wonder if it could be either the clock spring or the multi-switch cause the short. I checked the wires on the headlights and they are fine. Again the high beams work when the truck is sitting still and the fuse is new.
View 4 Replies
I purchased a 94 Ford Explorer 4x4 4.0L w/ Automatic transmission with Overdrive. Great work truck, but I am finding that these had a lot of wiring problems. First thing that messed up with me is the backup lights wouldn't work. Then the dash lights and parking lights stopped working (Still no fuses where bad). Then about 2 weeks later, I was on my way home when It just died like someone had turned the switch off, I pulled off the side of the Interstate, and after checking my fuses/Relays under the hood.
I found that the EEC Fuse (30AMP-BIG Fuse) had blowed, I didn't have one and the truck wasn't off the road good, So I wrapped a small wire around the fuse to see if I could start it and get it out of the road better, It started right up, but soon as I pulled it off the road it died again, and I found that it melted the EEC Relay, I went to the parts store and got a new relay and fuse and put them in, It blows the fuse as soon as I put it in, with the switch off or on. I just need to know what things will cause this so I can check them out one by one, until I find the one that is causing this problem, cause It run great up till this happen.
Only other thing I may need to let you know, Is when I bought it, the key switch would start it, The guy had put a push button starter switch that you push to start it with the key on, I unhooked it, and it started fine with the key for a while then it stopped again, so I had to hook the push button back up and had been using it until it stop running with me.
View 1 Replies
I have a 1990 f-150 that periodically (and rapidly) blows the fuse for the turn signals. The brake/tail lights continue to work, but just the turn signals quits. Looking for a schematic of those systems?
View 1 Replies
I posted earlier about the tranny in my 01 Ex v10 having a transmission problem. The show looked at it and found the O2 sensor had shorted out and in some way sending the truck in to limp home causing the tranny fuse to blow????
Any way they fixed it or so they said and I drove it for a few hours and it did fine. The next morning I drove it and it blew the fuse. (under hood box I belive #19) I took it back to the shop and they beat and banged on it....got it wet etc. and can not get it to do it again. I know whe have an electrical issue but what all runs off of the fuse that controlls the tranny?
Is there any online wiring diagrams of excursions or superduty drive trains? Where all to look for the problem?
View 4 Replies
I have a 2006 f350 king ranch 4x4, I recently used 4 wheel drive and could not disengage it, it would go into 4 low but would not go back to 4 high or 2 wheel drive, I unplugged the actuator harness and applied 12 volts to the terminals and it disengaged, I reversed the power and it engages, the actuator seems to work properly, I then replaced the two relays located by themselves on the front fender driver side, when I try to install the 30 amp female fuse located in the outside fuse panel rear driver side, fuse #3 for 4x4 shift on the fly it blows immediately, it makes no difference if the harness is plugged into the actuator or not, if I remove the two relays then I can install the 30 amp fuse, but as soon as I try to install the relays it blows the fuse again..
View 6 Replies
