Ford Wiring/Electrical :: 2006 F150 - Turn Signals Won't Work


Feb 15, 2014

I have a 2006 f150. Both front turn signals do not work. I replaced bulbs still nothing. There back signals do work. They blink really fast.

View 4 Replies

Advertisement

Ford Wiring/Electrical :: 2004 F150 - Brake Lights / Turn Signals And Flashers Not Working

My brake lights, turn signals, and flasher are not working in my truck. Is it a fuse and what fuse? Could it be a relay?

View 2 Replies

Ford Wiring/Electrical :: Turn Signals Will Not Work With Engine Running

My turn signals will not work with the engine running. With the engine off they will. With the engine running if I move the ignition like I am going to turn it off they work.. Is it the ignition switch or ign cylinder....

View 5 Replies

Ford Wiring/Electrical :: 2005 F250 - Rear Turn Signal Signals And Brake Lights Don't Work

I just bought an 05 F250 XLT. I noticed tonight that the rear turn signals and brake lights don't work.

The front turn signals work fine, although they flash fast. I know that usually means a light on its way out. neither taillight flashes though, which puzzles me.

My second issue is that, of the 3 brake lights, only the high mounted light illuminates when I hit the brakes.

View 1 Replies

Ford Wiring/Electrical :: 2006 E350 - Flasher For Turn Signals

I must be missing something here. Where is the flasher for the turn signals? It isn't the two relays behind the radio is it?

View 2 Replies

Ford Wiring/Electrical :: 2001 - Turn Signals Stop Working When Vehicle Heats Up

I have a 2001 Econoline and the turn signals work in the morning but when the vehicle warms up they stop working. I have replaced the bulbs and the fuses. What I could try next.

View 4 Replies

Ford Wiring/Electrical :: Passenger Side Does Not Light For Brakes Or Turn Signals Suddenly

I installed LED tail lights a few months ago, now all of a sudden the passenger side does not light for brakes or turn signals. The lights came with resistors that I put in when installing and the adhesive wore out and they were dangling in the truck frame. The wires connecting the resistors to the light were damaged. I taped the exposed wires and secured them a with a heavier tape, but taping did not work. I also tried switching the resistor packs with the driver side to see if it was them that have an open winding, but they are still operable.

I narrowed it down to wiring between the trailer hook up and passenger light assembly in the electrical circuit. I plugged an LED light bar into the trailer connection and the same problem occurred (running lights come on, but no turn signal or brake light). Where could there be a short? Or is this circuit fused somewhere that the running lights come on but a separate fused circuit triggers the higher voltage for LEDs.

View 9 Replies

Ford Wiring/Electrical :: 2004 F250 - Turn Signals And Hazards Stopped Working

So I have an 04 F250 Super Duty 6.0L and suddenly the turn signals and hazards stopped working. First I replaced the switch on the steering column...no luck. Today I replaced the flasher relay under the dash panel (the blue one)...still no luck. I remember checking fuses in the fuse box but don't remember which ones I checked but I didn't see anything obvious. I also took a quick look under the dash at all the wires for any anomalies...nothing. I'm lost... What to do next!?

View 1 Replies

Ford Wiring/Electrical :: 1973 F250 - No Turn Signals / Brake Lights Or Rear Hazards

Dad borrowed truck and wired 7 pin trailer harness. Lights worked on truck/trailer for use but upon return the turn signals didnt work. Hazards and running and brake lights did work. Replaced TS flasher and Haz flasher. Still no signals. Pulled steering wheel and replaced turn signal cam only, not whole switch. Now no brake lights, no rear hazards or turn signals. Losing my marbles trying to follow schematic and using test light and mulit meter. All bulbs and fuses are good. Running lights and head lights working as well.

View 6 Replies

Ford Wiring/Electrical :: 2001 F350 - No Turn Signals When Start The Truck - Fuse 1 Keeps Blowing

2001 F-350 diesel. Out of nowhere, I start the truck and there's no turn signals. Fuse is blown so I replace it. It immediately blows. Tail lights work. No turn signal, brake lights, or hazards. I haven't hooked up a trailer or done anything abnormal recently. Only the #1 fuse (20Amp) is blown. Pulled bulbs and they work fine. Inspected wiring under and near lights. NOTHING! Any way to localize a short?

View 2 Replies

Ford Wiring/Electrical :: 1990 F150 - Turn Signal Fuse Blew?

I have a 1990 f-150 that periodically (and rapidly) blows the fuse for the turn signals. The brake/tail lights continue to work, but just the turn signals quits. Looking for a schematic of those systems?

View 1 Replies

Ford Wiring/Electrical :: 1986 F150 - No Gauges / Left Turn Indicator Light On Dash Does Not Come On

Okay, my 1986 f150 with a 351w (non-feedback carbed) Has no lights on the cluster, and none of the gauges work (haven't tested the speedo yet, truck is not registered yet).

I also have a minor issue with the turn signals... Fronts work, no rears. The left turn indicator light on the dash does not come on but the right turn one does. All my "primary lights" (markers, tail, headlights) work fine. I have not yet tested the brake lights.

Fuses all look good, truck did have some roof leaks. I've done some research, does this sound like the dreaded voltage regulator issue for the gauges?

My assumption for the left turn indicator light is that there is a replaceable bulb in the dash (probably blown), is that right? Rear signals might be wiring (PO installed his own trailer wiring) or bulbs? haven't gotten that far into it yet...

View 8 Replies

Electrical-wiring - Chevrolet - Equinox :: Turn Signals And Hazard Lights Stopped Working

I have checked the fuses for the Hazard and the Turn Signals. Both look fine. I tried replacing the turn signal flasher (which was a task in itself). After all of this it is still not working. What else could it be? Simple short?

View 2 Replies

Ford Wiring/Electrical :: 2006 F150 XLT - Map Light Blinks When Starting And Driving

I have an 06 F150 XLT and lately the map lights blink when starting and driving. This does not occur every time but it sure is a problem when driving at night. What is causing this and hopefully a minor repair.

View 1 Replies

Ford Wiring/Electrical :: 2006 F150 - Back Speakers No Vocals - Produce Bass Only?

I have another question my front speakers work, they produce vocals and bass. My back speaker only produce bass! NO VOCALS? Why? Is this normal? I only realized this today. I drive a 2006 ford f150 supercab.

View 1 Replies

Ford Wiring/Electrical :: 2010 - No Brake / High Mount Brake Light / Rear Turn Signals?

2010 F-250 14,000 miles, gas engine with Knapheide utility bed. Tilt wheel has been kept in the up position from day 1.

The problem:
No rear brake lights.
No high mount brake light.
No rear turn signals.
No rear hazard flashing lights.
All trailer lights work.
All other truck lights work.

Things checked: Fuses all OK. Visual inspection of multi-function switch. Looks clean. Brake switch at brake pedal has power on one wire. Jumpered the other wire-no brake lights.

I need to haul my trailer and am nervous when I see a Savannah, GA metro police car.

View 8 Replies

Ford Wiring/Electrical :: 2006 - Fog Lights Don't Work?

I don't know if this goes here but I ha a ford f350 king ranch 2006 I got it 5 months ago the fog lights never did work. One of them was burnt out.

I replaced them both today and checked the fuse and they do not come on. I checked the fuse under the dash kick box. What else could be going on here hat I can look into?

View 14 Replies

Ford Wiring/Electrical :: 2006 F150 - Battery Light On / Voltmeter Spikes / Grinding Noise As 4x4 Engages

Problem with my 2006 F150 5.4 4x4... Voltmeter spikes, battery light comes on, grinding noise as 4x4 engages on its own then everything returns to normal after about 60 seconds. Took to Ford who replaced the alternator and battery, still doing it so they replaced the alternator again...they checked the wiring and replaced some other misc parts and don't know what the problem is. The problem occurs once every few days, after only a few minutes or after a few hours, completely random.

View 6 Replies

Ford Wiring/Electrical :: 1987 F150 - Wiring Diagram With Carburetor?

Looking for a wiring diagram for a F-150 XLT LARIAT 5.8L 4BBL, all the books I have looked at show the wiring for this year with fuel injection and this truck came with a 351W with a Holley 600 4BBL, I have a few wire's in the engine compartment that melted away all the insulation, they are located close to where the harness passes the firewall before the ignition module. Is this a common problem on old models ?. Need a clear copy of the correct diagram for a f-150 1987 with carburetor, how I can get a copy so I can fix this problem before it gets worse.

View 3 Replies

Elantra HD (2006-10) :: Turn Signals Work But Hazards Do Not

Today, I replaced the flexible coupling in my steering column. All went well and seemed great until I realized my turn signals were not working. I tried the hazards and promptly heard the 10amp fuse blow. I took the paneling back off and realized that the wire bundle to the turn signal was being pinched above the steering column.

After lowering the front of the column down and removing the wires, I noticed that there was some damage. One wire (blue) was cut and a few others had damage to the sleeves. I repaired the sleeves and fixed the broken wire. The turn signals now work perfectly fine, but when I activate the hazards all the signals go dark. I cannot find any blown fuses and the relay appears to be working just fine for the turn signals.

View 2 Replies

Sonata NF (2006-10) :: 2008 - Turn Signals / Hazards Won't Work

I recently bought an 08 Sonata from a used car dealer which has 65,xxx miles. Last week my turn signals would work intermittently, and now neither the turn signals or the hazards work. I put in a new relay and a new turn signal switch, to no avail. When I turn the hazards on, the relay clicks once then nothing. When I do the turn signals, nothing clicks. Is there another relay I'm missing somewhere?

View 14 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved