While driving along my Expedition will completely shut down, ignition, all accessories, everything, for a few seconds then come back alive. It happens generally up hills or around right turns.
It is like the main ground strap is loose and losing contact momentarily. I don't know where to look for this. Engine was replaced 1500 miles ago. Battery and all visible connections seem ok.
I have a 1996 F250 460CI that was running great for years and all of a sudden it shut off for a few seconds when I was on the expressway. It was like turning the ignition key off and turning it back on. It did it several times and eventually just died and would not start. I put a new coil on and it worked fine for about 150 miles and now it started doing the same thing again. The check engine light was on for a few seconds but not all the time so I am not sure if diagnostic equipment will show any error messages. Mileage on my truck is 92k. Does this sound like a distributor pickup issue?
View 6 RepliesMy vehicle would not turn over and we could tell it was fuel related. The fiel pump relay has burnt through the motherboard of the fusebox. It is my understanding that this cannot be fixedand another fusebox must be installed. I have been to many junkyards in my are looking for it to avoid the dealer prices..all of the expeditions that we have found locally have already had the fusebox pulled. Any other vehicles that this might be interchangable with? My friend has an 01 expedition..would this work?
View 1 Replies1998 Expedition EB, the lights on my running boards do not work. Checked online and can not locate the fuse for them, checked the lamps and found one that is burnt out. Here's the dumb question, if one bulb is out will that make the other three not work, something like the Christmas light strings?
View 4 RepliesI bought a 84 ranger 2.0 that ran when parked sat for six months. Cranks all day long but only sparks when you shut the key off. Replaced the ignition switch (by key) ( someone told me there is another ignition switch under the dash?? is this true?) Tested the icm and it passed all wires seem to be fine. I am just wondering if something in the dizzy could cause this or possibly the starter solenoid?
View 9 RepliesI have a 06 f350. Out of the blue my wipers will not shut off without pulling the 30 amp fuse in engine compartment . Even with ignition off.
View 7 RepliesI have a 1983 Dodge W150 that has a problem. It stops running with the electrical system completely shut down. If the battery is taken out of the system, and then reconnected, it starts and runs fine. Some history: a trailer brake control was installed a few years ago. Where the wire ran from the battery through the firewall, the insulation chafed and eventually shorted out. The fuseable links were burned out. I disconnected the brake control from the battery and replaced the fuseable links with a fuse block. The truck ran fine for 18 months. It has stopped twice in the last couple of days. Apparently something like a circuit breaker is tripping and then resetting when the battery is disconnected and then reconnected. My questions are
1) what is the breaker likely to be intended to protect,
2) where would the breaker be found, and
3) what is the likely cause of the breaker tripping (a short, but in what system)?
I'm planning the install of a 1996 351w into my '77 F-100. I'm using the '96 accessory serpentine drive (FS-10 A/C compressor, '96 alternator, etc.). It needs to mate up to the '77 wiring. I'm going to use stock '96 underhood A/C components (accumulator, hoses, condenser).
As best as I can tell, the '96 system uses the ECU to manage the A/C system, but I've converted the '96 motor to a carb.
Looking at both the '77 and '96 systems I think the easiest underhood wiring solution would be to use the '77 compressor ON wire as a relay trigger, and use the '96 High Pressure Cut Off (HCPO) on the compressor manifold, and compressor cycling switch attached to the accumulator to interrupt the relay output to the compressor.
I can get the switches and pigtails, and I can look up their pressure trigger points, but I don't know the voltage the '96 switches operate at (12v or some reduced voltage?) or how to simulate their trigger conditions to see how they work. I guess that at ambient pressure the HPCO should be normally on and the cycling switch should be normally off. So I could just wire them into the relay ground or trigger connection. But of course they aren't simple two wire switches. (Edit: Looking at it online, the cycling switch appears to be two wire, the HCPO is 4 wire).
How to wire them, should I use them to interrupt the relay ground or trigger connection?
My Viper 2 way alarm, instead of the brain being wired to each of the 4 doors individually. The installer ran 1 wire to the dome light. Seems to work fine as far as arming/disarming/locking/unlocking, but since the dome light stays on for 10 seconds or whatever after the door is shut, when i arm it.
The 2 way remote says "door open" because the light is still on so it thinks a door is open. this eventually times out and all the sensors arm, but there's a long delay. it arms fine and no alerts pop up if i lock the doors first from the outside keypad on the door, making the lights go off, then hit arm on the viper, and everything is good to go.
Can I change it so no matter what, as SOON as i shut the door, the light goes off? I want there to be NO delay, if possible. If not, I may need to just have the installer run a wire to each door and take the single run to the dome light off, as it is sorta annoying to me.
I have an 03 v10 with a Powerdyne supercharger. The Ex came with an extra computer with a Superchip. The Superchip has a proper tune for the supercharger but when I install it with the extra "bad" computer the truck will completely shut down after driving ~100 miles. This is very dangerous because I lose power steering and brakes during the shutdown. The Ex starts back up after a few minutes and then shuts down more frequently until I reset the computer. I speculate that something is going wrong after the "bad" computer has learned the driving habits.
The other "good" computer works great and does not ever shut off the motor, but at full throttle the Ex will bog and I am losing HP produced by the SC. I don't think it has the optimal tune because my wideband AFR reads lean right before it bogs and I think it is bogging to protect the motor from a lean condition. I would like to install the chip into the "good" computer that never shuts the truck down to get the benefit of the proper tune, but I don't want to risk damaging it or experiencing the dreaded shutdown. A few questions :
- Why the truck shuts down while under power?
- Any reason to think that the chip will cause the "good" computer to shut down while driving?
- Could the chip be causing the shutdown, not the actual "bad" computer itself?
- Would the best option be to send the chip to 5star tunes and have them program a tuner with the superchip tune...and a few others?
- Any way to flash the "good" computer with the superchip tune?
2005 Ranger XL 2.3L 5 speed 2WD 305,000 miles. Alternator has about 100,000 miles on it.
Battery light came on about 0400 and 50 miles into my daily 90 mile drive to work, made it to work. After the truck cooled down for 3 hours and I got time I checked the battery voltage 12.6VDC and started the engine and the system is charging at 14.2VDC with no battery light on (battery light out when cold). Serpentine belt looks good, dry weather.
Other than alternator nearing end of life and being warm is there anything else that may cause battery light to come on.
My '05 Expedition will be driving normal at highway speeds, and when I need to apply a little more throttle to start up a hill I get a shutter thru the truck that sounds and feels like driving over a rumble strip. It doesn't last but just a second or two, but it happens frequently. Is it something in the 4wd? Transmission? or.......?
View 3 RepliesI have a F250 towing a Big trailer and the RV folks have told me that while the factory seven prong will supply power to the RV, it would take a days to charge the RV batteries. So...
1) Does the connector not really significantly charge the batteries?
2) Is there a faster way to charge the RV batteries while driving?
3) Would instructions something like I found at How to Charge Two 12 Volt Batteries on an RV Towed by a Ford F-150 | etrailer.com work?
4) Would #3 eventually tax my alternator so badly that I kill it?
5) Would #3 fry the electronics in the trailer?
I'm trying to charge 2 6-volt marine deep charge batteries in series.
so I was driving down the street the other day then my car completely shut off no interior lights car won't turn over radio wont turn on had to push it up the hill, to get it out of the street and get it towed.
View 13 RepliesSo I bought my 1987 F150 XLT 4X4 (4spd) about two weeks ago and haven't had any issues with it so far... until now. As soon as I got it I did a full tune up. Changed plugs, cap, rotor, fuel filter, new battery, sea foamed it, fuel filter, ran a bottle of fuel stabilizer through it, new pvc valve, cleaned the throttle body, oil change, etc., ( all the usual things).
Was running fine up until two days ago when I was driving down the highway doing about 90km/hr in 4th when the truck suddenly lost power, sputtered and died. Tried to start it again and it will turn over but not start. So I get a nice expensive tow home and start to diagnose the problem. It is not a fuel issue. I can hear the pumps coming on, and fuel is coming out of the fuel filter so I cross that off the list.
Next I check for spark. No spark at all. So I run some tests. Battery is putting out 12V, about 10 when cranking. The solenoid is getting power and putting out power. No visible damage to any of the wiring, and all the grounds look good.
Next I just went ahead and swapped out the coil thinking that could be the issue. Didn't work. So I preform some more tests on the old and new coils. Both are grounded and having voltage pass through them. Next I take the TFI module off the distributor and check for resistance. Everything still checks out fine. Now I am thinking that the only thing left could be the PIP in the distributor. So instead of taking the dist apart and screwing around I go ahead a get a brand new dist and throw it in.
Now I am stoked and thinking that I finally fixed my truck and go to start it up and.... no spark. It still turns over but no start. I am trying to provide every bit of detail that I can. When I say I tested all the components I mean I REALLY tested them. I did both tests from the Haynes manual and from various sources off this site.
I am almost at the point of getting it towed to the shop, which I really do not want to do. A day before this happened I degreased the engine and VERY carefully sprayed it off with water. In the process I am thinking I may have damaged something?
I have a 2004 Ford F-150 lariat with a bit of a problem. My running lights (not sure if correct term, I'm talking about the tail lights' illumination that stays on while you drive at night) are not working. My headlights and parking lights do work, and my brake lights and turning signals also work. I have put in a brand new brake light switch and checked every fuse and relay, but no luck.
View 6 RepliesMy 2005 4.6L 4x4 screw is blowing the 10amp a/c clutch, 4x4 solenoid fuse whenever i turn the a/c on, at times whenever I turn the defrost on. the fuse does not blow when i turn the key to power (no engine start) but when engine is running fuse will trip. I disconnected elect. Connection at compressor and fuse still blows, also seems like no power or life from compressor.
View 3 RepliesMy '84 F150 4X4 inline 6 Died last night while driving. just conked out and died right there on the spot. no sputter... no gasping... just instant death...
after some investigation i found i wasn't getting spark anywhere. not at the plugs, not at coil. I have replaced the ignition module to no avail. still no spark I am going to swap in a the coil tonight. sure do hope this works.
My 08 prius completely shut off while driving on the california freeways today. No warnings no lights on the dash nothing. Just powered off. Will not start the ready light of any dash lights for that matter work.. tried to jump it.. nothing working. What the he'll can cause thus.. I'm about 500 miles from home with a car just parked. Could a 12v battery cause this no start issue?
View 15 RepliesI have a 2005 Jeep Grand Cherokee Laredo. I took it to the dealership on June 30, for a routine oil change and other maintenance that was due. They did a cooling system flush, and oil change, a power steering flush, and a brake system flush, along with a multipoint inspection, and replaced the belt and tensioner. On July 18 on my way to work in traffic, the vehicle completely shut down with no warning signals. Shortly after the check engine light, the oil light came on. Until then, I had not noticed any warning lights.
At this time I reached down to get a bottle of tea from the passenger front floor board and noticed a slightly oily pink brown liquid on the plastic floor mat. When it was towed to the dealership, they tore the engine apart and reported that the engine overheated, the valve seats came off, the valves hit the pistons splashing metal onto the cylinder walls and requiring an engine rebuild. Is the dealership responsible for not having discovered whatever problem caused the engine to break down? Or causing it somehow during the maintenance on June 30? They feel it is not related.
I just bought a used F-350 that was being used by a fire department. They did something to the wiring to where most of the electronics won't work unless the key is in the "ON" position. When I open the doors, the dome light doesn't come on, nor does it come on with the IC dimmer switch, when I turn the key either backwards or to the "ACC" position the radio won't work, the headlights DO work but I don't get the warning chime when I open the door with them on.
The flash-to-pass works, as do the hazards and the turn signals (which seems odd -- I don't recall having a car where the turn signals worked without the car being on). With they key on, everything works including the dome light and the door chime. Is there some simple thing they could have done that would make it work this way and is easily reversed?