My 2005 4.6L 4x4 screw is blowing the 10amp a/c clutch, 4x4 solenoid fuse whenever i turn the a/c on, at times whenever I turn the defrost on. the fuse does not blow when i turn the key to power (no engine start) but when engine is running fuse will trip. I disconnected elect. Connection at compressor and fuse still blows, also seems like no power or life from compressor.
View 3 RepliesOverdrive fuse keeps blowing. Drive one and 2 shifts fine. 3 and overdrive don't work. Had transmission checked it is fine. Repair shop says it is electrical.
View 1 RepliesI have a 1994 Ford Ranger king cab 4x4 with a three inch lift kit on it . My problem is the fuse is blowing that goes to the fuel pump . It started out blowing the fuse now and then when it was raining . Well I thought it mite be the fuel pump going bad but after I put the new pump in the truck it lasted about a week and started blowing fuses again . I put another fuse in and it go a few days and blow it . Last week on a 100 mile tripe I got almost there and it burned a fuse on the highway . I tried to put another fuse in and it would blow it as soon as I tried to start the truck . Burned five fuses right then . So I had it towed to mothers house and put another fuse in and it cranked up . I looked at the wiring that was not wrapped in that plastic cover stuff and have not found anything yet ...
View 14 Replies2006 F-250 SD... I Keep popping the 15A #17 fuse under certain conditions - Driving forward
1. Start with good fuse.
2. Start engine, while in park, turn on parking light...4.8A on circuit. No problems.
3. Put into reverse and drive. down the block around the corner and back up to the house... No problem. 4.8A on circuit.
Put the shifter into drive and - POP - the fuse goes. I never see a jump in the current. 1-5 seconds until fuse goes. While conducting testing, I have had the fuse blow when shifting from reverse to park. Looking at the wiring diagrams, I don't see a common wire that would cause a short when shifting. What I should try next?
I have a 1994 f150 5.0 engine and automatic transmission. Problem I am having is speedometer, cruise control is not working. Overdrive light is flashing and number 18 fuse keep blowing. horn is still working...
View 1 RepliesI purchased a 94 Ford Explorer 4x4 4.0L w/ Automatic transmission with Overdrive. Great work truck, but I am finding that these had a lot of wiring problems. First thing that messed up with me is the backup lights wouldn't work. Then the dash lights and parking lights stopped working (Still no fuses where bad). Then about 2 weeks later, I was on my way home when It just died like someone had turned the switch off, I pulled off the side of the Interstate, and after checking my fuses/Relays under the hood.
I found that the EEC Fuse (30AMP-BIG Fuse) had blowed, I didn't have one and the truck wasn't off the road good, So I wrapped a small wire around the fuse to see if I could start it and get it out of the road better, It started right up, but soon as I pulled it off the road it died again, and I found that it melted the EEC Relay, I went to the parts store and got a new relay and fuse and put them in, It blows the fuse as soon as I put it in, with the switch off or on. I just need to know what things will cause this so I can check them out one by one, until I find the one that is causing this problem, cause It run great up till this happen.
Only other thing I may need to let you know, Is when I bought it, the key switch would start it, The guy had put a push button starter switch that you push to start it with the key on, I unhooked it, and it started fine with the key for a while then it stopped again, so I had to hook the push button back up and had been using it until it stop running with me.
I posted earlier about the tranny in my 01 Ex v10 having a transmission problem. The show looked at it and found the O2 sensor had shorted out and in some way sending the truck in to limp home causing the tranny fuse to blow????
Any way they fixed it or so they said and I drove it for a few hours and it did fine. The next morning I drove it and it blew the fuse. (under hood box I belive #19) I took it back to the shop and they beat and banged on it....got it wet etc. and can not get it to do it again. I know whe have an electrical issue but what all runs off of the fuse that controlls the tranny?
Is there any online wiring diagrams of excursions or superduty drive trains? Where all to look for the problem?
2001 F-350 diesel. Out of nowhere, I start the truck and there's no turn signals. Fuse is blown so I replace it. It immediately blows. Tail lights work. No turn signal, brake lights, or hazards. I haven't hooked up a trailer or done anything abnormal recently. Only the #1 fuse (20Amp) is blown. Pulled bulbs and they work fine. Inspected wiring under and near lights. NOTHING! Any way to localize a short?
View 2 RepliesI'm having brake light issues with a 2001 Suzuki Grand Vitara. The brake light fuse keeps blowing. The last time driven with me following the driver side brake light was dimmer than the passenger side. At one stop the driver side brake light pulsed brighter for a split second then went back to dim. A few stops later it became as bright as the passenger side and stayed that way for the rest of the trip. The driver put in a breaker fuse and it was in during the observed trip. I'm not sure of the brake light visual symptoms without the breaker fuse in other than that the fuse keeps blowing which prevents the vehicle from being shifted out of park. What the problem could be? Bad ground?
View 4 RepliesSo I'm writing this for my friend but he has a 1978 F-150 with a 1969 390 in it. He recently had a problem where his starter got stuck and it lit the wires connected to the solenoid up in flames. Well anyways we replaced all the wires that were attached to the solenoid and replaced the solenoid and the starter also. But after wiring it up it has no power whatsoever. The battery is also brand new and the fuse links are fine. What is causing this?
View 2 RepliesI just replaced my starter solenoid and I'm getting nothing. When 12 volts are applied directly from the battery to the solenoid, the engine wants to turn (granted my batteries are weak) however when I turn the key to start, after waiting for the "wait to start" light to go off and hearing the glow plug click, I turn the key and I get absolutely nothing. No click, nothing. Is there a possibility my ignition is bad?
Would the "wait to start" and glow plug keep working if this were true? Electrical is not exactly my forte'. Before I replaced the solenoid, the bad one had a broken post but the truck would still start most of the time, and when it wouldn't I just connected the two large posts on the solenoid with channel locks or pliers or whatever was handy. I put the new one in exactly the same way the old one came out. I only undid one bolt and set of wires at a time so I wouldn't screw the order up, so I'm at a loss.
Just this morning, my 2006 Azera Limited would not cycle on the A/C. I found that the 10 amp fuse for the A/C solenoid had blown. I replaced the fuse. The A/C worked perfectly, blew ice cold air, for about 15 minutes. Then the fuse blew again. Replaced the fuse again, the compressor clutch kicked and started to turn compressor and fuse blew yet again. Replaced fuse a third time, blew immediately. And now tonight, the dash lighting will not go into "night mode" - will not dim the instrument cluster fully, and the night illumination on controls will not light. Also, randomly, the fog light indicator will not light - even though the fog lights are on and illuminated. Not sure all these things are related, but it seems like some sort of major failure is occurring somewhere. I looked for shorted or burnt wiring under the hood, couldn't find any. Other than taking the car to Hyundai and paying two arms and a leg? I have seen posts for other Hyundai models where the compressor wiring shorts against the compressor - but so snug down there I haven't been able to check it properly yet. Also, another post suggested the clutch coil may be bad? But if it was, would it kick in and run properly for 15 minutes? I'm mechanically inclined, have done a lot of work myself on cars for over 20 years, but this one stumps me...
View 4 RepliesI'm not too knowledgeable about wiring and electrical systems. I'm getting a P1451 code (EVAP Control System Canister Vent Solenoid Circuit Malfunction) on my 99 4.2. I've read that it could be a bad solenoid, bad wiring, or a blown fuse. So far I've;
- checked (and changed) the related fuse
- checked the wiring for damage at the connector
- checked voltage at the connector (12 volts)
- checked the resistance at the solenoid (around 60 ohms)
- actuated the solenoid with a 9V battery (can hear it opening and closing)
I haven't had a chance to check the wiring all the way back up the frame to yet, but I noticed that the ground at the trailer wiring harness has broken off the frame. Would this potentially cause a fault in the upstream wiring? I'm going to slap a new connector on and bolt it back down anyway, but as it's Labour (Labor) Day I'll have to wait for the stores to be open tomorrow.
I need to hook up a lamp for my mechanical oil pressure gauge and tested all the fuses, they are either on or on with key in run position, but I found none that went on with the lights, which of course is what I need. So now I guess I start randomly sticking needles in wires under the dash and testing for a possible light switch dependent circuit? Or run a wire through the firewall and tap a wire near a running light? There's got to be an easier way, but my Haynes manual seems useless--one wiring diagram for 1995-2008. I will be forced to run it off a key on circuit which means the lamp will be on anytime I drive, day or night, unless I install a toggle switch--not the best way to do it though.
View 3 RepliesI want to add a CB and some flood lights to my pick-up, but am getting tired of hunting for wires that are constant hot or switched hot under the dash. Not to mention the rats nest of wiring that results, and the potential for overloading the factory wiring.
Above is a diagram that I came up with while trying to figure out how to add a constant hot fuse block, and a switched hot (or ACC) fuse block to the truck to clean up the wiring.
Am I using the relays in the right way? (Never used one before)...
I have a main tank and an Aux tank with a gauge selector switch. I believe I may have a bad fuse as the indicator has stopped working. Where it is on the fuse block??
1978 Ford F-250
I recenty was having some problems with my 2003 6.0 liter. My FICM connection was not seated all of the way which casued my truck to just die without warning....... AFter I had fixed that, my stereo died. Just dead??? Nothing...EVERYTHING ELSE WORKS???
So, after I had messed with everything I could think of, I thought, OK new DVD/Stereo time.
I checked fuse #32 which was the fuse to my stereo. The fuse is fine...BUT...There's no friggen power to the fuse via my test light. Test light works on other fuse spots so I know i"m not getting power to the fuse #32.
Since I don't have any power to this fuse....WHAT NOW???? How to trouble shoot this problem?
I have a 2006 F350 Diesel. Had one of my employees go out to start the truck yesterday and when I went out I had no electrical power to most of the accessories (gauges, warning lights, power windows, radio, interior lights, turbo charger). It also seems to have no power - could barely make it go up the slight incline into my garage. I have checked all the fuses - they seem fine. Although put a tester on the interior fuse box and I don't have any power to the fuses that run these accessories.
View 10 RepliesFuse #41 keeps blowing...scan tool says o2 sensor heater circuit malfunction. Problem is that when the o2 sensors are unplugged it keeps blowing fuse the second I hit the key. Where this short would be? I can't find a wiring diagram anywhere. ( I'm new to this forum and I'm sure there is a sticky somewhere..
DTC codes: P1451, P0743. P0750. P0760. P0765. P1747. P0135. P1409. P0755. P0155
My A/C clutch fuse (#46) keeps blowing when the car is started but a/c is not on. Checked relay, it's ok. Unplugged compressor but the fuse still blows. Fan works, heat works, but no cold air.
View 1 RepliesI have a 1997 Expedition that every time I replace the #16 fuse it blows when the high beams are on. It seems that it happens only when in drive and accelerating from a stopped position. I wonder if it could be either the clock spring or the multi-switch cause the short. I checked the wires on the headlights and they are fine. Again the high beams work when the truck is sitting still and the fuse is new.
View 4 Replies