My 2004 expedition wont go into any gear the shifter will not move I changed the stop light brake switch and a 30 amp buss fuse I found blown and also the check engine light is on now too this was after I parked it I also changed a 30 amp buss fuse I found blown out but it still don't work the only way I can get it into gear is to push the little button under steering wheel...
View 2 RepliesSometimes the headlights won't come on unless you move the steering wheel up & down.
View 1 RepliesMy 2000 ford excursion gauges fuse keeps popping. It started earlier this year and I couldn't pin point when it would pop. Now I'm sure after 30.00 worth of fuses that it happens when I change the gear shifter from park or rev to drive.
View 5 RepliesI need removing the console on a 2005 Malibu Max. The switch on the shifter will not move the transmission down to 2nd or 1st gear. There was a post by "shadow5599" on 05-05-2009 stating that this problem was caused by a broken wire in the harness under the console leading to the shifter +/- switch. He said it was easy to fix but the console needed to be removed. Later on the same day he posted that he had just posted the instructions on how to remove it. I'm a first time user on this site and I haven't been able to locate those instructions.
View 1 RepliesI have a 2004 2.0L Jetta with a 5 Speed manual transmission.
When shifting into third gear sometimes I push the shifter forward and it does not want to move all the way forward. It feels like I am pushing the shifter knob against a wall, or more accurately the bottom of the shift that pulls the cables feels like it is hitting a wall. If I pull it back out and press it in hard it will go into place sometimes.
This also solves the problem: While the shifter is mid shift into third, at the wall/ at the point of resistance, I let off the clutch slightly to give the flywheel some friction. This rolls the transmission a bit and allows third gear to slide into place.
I have experience with a MK4 Audi TT 1.8T that cam with a 6-SPD and it at had a 1-2 and 2-3 synchronizer issue (The one where the nipples are worn and it grinds at higher RPMS because they can no longer make a firm handshake). The issue I am experiencing is not that.
Could it be the transmission cables? Could it be some other cogs in the transmission? - If so does this mean I need to buy a used one? My car has 180K miles on it with the original clutch.
Here is what I have:
2009 Santa Fe 3.3L AWD
70k KMs / 43k Miles
Temp has been very cold, -20C / -4 F
Car starts up without any problems. Try to put car in Reverse and the shifter is very hard to move, if it moves at all. When I am able to get it into Reverse, I then try to put it in Drive and it does not "engage" the "D" and the car behaves like its in Neutral. Moving the shifter back to Park, Neutral, Drive is very difficult and sometimes it will not go into Park. The dash lights do not illuminate the selected P, R, N, D.
However, once the car is warmed up (no longer on C on the temperature gauge) I can with a little effort move the shifter freely (but more effort than it should take) and the car behaves normally. Gear shifts are smooth and in general it is operating normally.
The dash lights do illuminate the selected P, R, N, D. I've checked the Trans fluid level and it appears to be normal and was planning to change it this w-e but I'm no longer sure it will work. Even if it has never been changed.
Also note that I have recently changed a wheel/hub bearing due to a noise that sounds a lot like loud tires on a highway. The bearing change did not eliminate the noise and I assumed that I've changed the wrong one. The noise does not appear to be coming from the Trans, but I cant be 100% sure. The noise is speed related and occurs only after about 20KM/h 16MPH. Unsure if they are related..
Got in to go to work this am, and the gear shifter was difficult to move. What to check?
I drove 70 miles to work and didn't seem like any issues with the transmission shifting.
Got in to go to lunch and it seems even more difficult to move...
Shifting back and forth in the selector seems to loosen things up a little.
A friend move the selector while I looked at the linkage and the bracket that support the cable is flexing while shifting between gears....More likely a transmission issue or something with the linkage?
Truck is up in the back country and has quit. It has two factory gas tanks, I can't hear either of the fuel pumps will come on when you turn the switch on. The problem started as an intermittent fuel starvation issue. Truck would act like it ran out of gas then pick up and go again. Switched tanks back and forth but it got worse throughout the day and finally will not start at all. I have listened to both tanks when the ignition switch is turned on but can not hear the pump come on for either tank (switching the selected tank with the switch on the dash). We went through some bumpy terrain just before the problem started so I am thinking maybe a wire might have come loose or got broke somehow. I am asking for wiring schematic so I can check for voltage in the correct place going to the fuel pumps. Both tanks are full of gas so for now dropping either tank is not an option.
View 8 RepliesHaving a chance to try an O2 Sensor Simulator on your truck? I am wondering if they actualy work or if I should just stay away from them. Are there any problems or improvements using a SIM?
View 13 RepliesI have a 94 Fsuperduty with a flatbed and lift that folds up and stores under the end of the bed. Recently while on a job the lift wouldn't go up, so I checked the one fuse I know of in the system and it was burnt. Put a new one in and before the lift reached the top it burnt-out again. It had been working with no problems for months prior to then.
View 4 RepliesLooking for a source for a wiring diagram for the 2003/4 f350 instrument cluster, specifically the wiring/connectors to the gauges? A link to a PDF file would be nice. I would like to try and disconnect the PCM control to the transmission temperature and engine temperature and drive the gauges from my own sensors to bypass the non-linear behavior that ford decided was in our best interest. I am NOT interested in installing any more gauges, just want to control the ones already present with my own signals. It is possible that these gauges are all addressable devices on a common bus, instead of individual controls.
View 8 RepliesIm installing a set of 04 lariat seats into a 00 truck. I need to know how to hook up the heat. The power part is no problem. What I thought was right which was a separate constant 12v and a switched 12v for the module and ground apparently isnt right. If somebody could ohm out their harness on a 01 truck that would be great. As I have it right now the light on the switch comes on but almost instantly turns off.
View 14 RepliesThis morning as I get in to drive my kid to school (2005 2.7 2 wd auto) as I go to put it in reverse I noticeably have to pull it with some force. I have never had to "force it" before, it had always switched gears with ease. This time it felt very stiff but had no issues going into gear. After I dropped my son off at school I went through the gears up and down and it felt very stiff (at this point i have no issues with starting it or P).
At lunch I go out to get something to eat and when I go to start it up it won't start. I try and try and nothing. All the lights came on, it's not a battery issue at all (brand new). But after 10 tries it starts, so I'm pretty happy. Then I go to put it in gear (reverse) I can not press in the button on the side of the gear shift. It will not go in. I press with all my might and it wont budge. But again, after about 10 good tries at it goes in and I can then select my gear but still feels very stiff.
After stopping again I didn't shut off the engine and dicked around with the shifter basically figured out that my car is not recognizing Park. On the instrument panel each gear lights up but not P. It gets very stiff when trying to put it in P but it doesn't actually go into P. If I put it in P (or really the further up it will go) and shut off the car, it won't start again. I can start it up in N and only N.
I have a 70 Ford f250 with a messed up wiring harness. Truck will run only in start position. which wires are wrong.
View 7 RepliesI bought a great 76' SuperCab with a 390 4 barrel Wednesday (the 30th) and while driving around the neighborhood this evening the truck just lost all power and came to a stop. No lights, no engine, nothing and I cruised to an easy stop (fortunately at the end of my own block). I thought I smelled a bit of electrical burn for a moment after I came to a stop but could not track it down before the smell disappeared.
Some early symptoms - on drive home from purchase, the turn signal light function was in and out. The starter was also turning slowly and sounded tired/weak. The ignition switch was a bit loose and previous owner said you had to make sure the key was not all the way to the right or accessories would not work.
Some early checks/fixes- replaced battery and battery cables and checked grounds. Starter began turning stronger and turn signal lights were back. Thought I had it going well.
My 85 f150 5L is parked to far in into my alley.. the last time i saw my keys i moved it up to water the plants that it was tucked almost on top of.
ive been looking for the keys for 2 months.. the truck isnt being driven at all but i think my neighbors are getting mad at it being out so far.
I can get in the engine bay, and i have jumped the starter on our big trucks at work before.. but what wires do i have to join to put the ignition into the run position?
Just recently bought a 07 Nissan Maxima SE. Has a few issues.
The car sun roof does not work at all. It worked the day I bought it though.
Has issues turning on. Cranks slowly then after a few seconds of struggle it turns. Didn't have this issue when I bought it.
Goes idle when first starting to drive. From park, I put the car in drive, or reverse, and let go of the brake, it basically does nothing. Engine is on as if it were in park or neutral, but the car doesnt move. When I press the gas it takes a few seconds before it decides to actually move.
So my friends 2002 camry has a problem where she shifts the shifter into drive, but the gear position indicator in the cluster still shows her in park, and the car will still be in park with parking pawl engaged. is this a sensor that went out, or a deeper transmission problem to be dealt with?
View 1 RepliesI just bought a used F-350 that was being used by a fire department. They did something to the wiring to where most of the electronics won't work unless the key is in the "ON" position. When I open the doors, the dome light doesn't come on, nor does it come on with the IC dimmer switch, when I turn the key either backwards or to the "ACC" position the radio won't work, the headlights DO work but I don't get the warning chime when I open the door with them on.
The flash-to-pass works, as do the hazards and the turn signals (which seems odd -- I don't recall having a car where the turn signals worked without the car being on). With they key on, everything works including the dome light and the door chime. Is there some simple thing they could have done that would make it work this way and is easily reversed?
2002 Ford F250 V10 Auto... When I put the transmission into reverse, the starter kicks in...
View 8 RepliesI have a 1998 Ford F-150. It has an issue with starting sometimes. The truck won't start with a fully charged battery but when I hook it up to a charger, the truck starts normally. It was going to get the wheels aligned today and when the mechanic went to drive it off the ramp, it wouldn't start. I told him to put a charger on the battery and it started right up. Without the charger it just cranked over and wouldn't start. It doesn't do this every time I go to start it only occasionally. The mechanic had no idea what the problem was and has never heard of this kind of situation. I'm assuming it is an electrical problem but I'm not an expert with engines. The battery was fully charged at the shop and the battery is a year old.
View 4 Replies