Ford Wiring/Electrical :: 2004 - Instrument Cluster Wiring Diagram?
Jul 24, 2004
Looking for a source for a wiring diagram for the 2003/4 f350 instrument cluster, specifically the wiring/connectors to the gauges? A link to a PDF file would be nice. I would like to try and disconnect the PCM control to the transmission temperature and engine temperature and drive the gauges from my own sensors to bypass the non-linear behavior that ford decided was in our best interest. I am NOT interested in installing any more gauges, just want to control the ones already present with my own signals. It is possible that these gauges are all addressable devices on a common bus, instead of individual controls.
View 8 Replies
Advertisement
I am a beginner when it comes to anything involving wiring. I am looking to re-wire all of the wiring coming off of the instrument cluster gauges. Once I have completed all of the wiring on the gauges, I may feel confident to move onto something else. As of rite now, it appears as though my truck is still running on all of the original wiring, and over the past few weeks, I have been having many wiring related issues. I found a schematic that includes the wiring for the gauges that I am going to go off of. I have a couple of questions before I begin.
1.) On the schematic, it shows connectors such as "Connector G" which is moving all of the gauges wires to there locations. Do I need to use a specific Ford connector, or could I purchase a new connector at any hardware store that carries them? As far as I am concerned, connectors do the same thing as all other connectors. (Let you connect and disconnect for easy instrument cluster removal.)
2.) I am not looking to purchase one of those expensive wiring harnesses. I would like to just purchase some wire that I can cut / use myself. What brand / type of wire should I be looking to purchase? I do not care if it is striped / colored as I will use wire tabs to name / label each wire.
Other than that, I feel confident enough to attempt something such as this. Here is the wiring schematic I am going to use.....
View 10 Replies
Any COMPLETE headlight switch wiring diagram? Everything I find online only shows 2-3 wires in each sub connector, nothing with all wires and colors, and what they do. and of course the factory service manuals no longer work on my new computer. the switch and associated wires went up in smoke 2 hours ago, and this truck is my only means of transportation rite now. what i need is headlight wiring with colors so i can temporary hook up a toggle switch to have lights until the new switch and connectors come in next week. I went to pull the switch and connectors out of the parts truck, but of course that does not have fog lights so it uses different switch and connections.
View 14 Replies
Looking for a wiring diagram for a F-150 XLT LARIAT 5.8L 4BBL, all the books I have looked at show the wiring for this year with fuel injection and this truck came with a 351W with a Holley 600 4BBL, I have a few wire's in the engine compartment that melted away all the insulation, they are located close to where the harness passes the firewall before the ignition module. Is this a common problem on old models ?. Need a clear copy of the correct diagram for a f-150 1987 with carburetor, how I can get a copy so I can fix this problem before it gets worse.
View 3 Replies
I am curious if it is possible to make a stand alone controller for the electric shift transfer case in a 2000 F-350?
The reason I ask is, this is swapped into a 4x4 conversion in a van and I would like the transfer case to work like the factory, but I don't want to swap over the whole GEM module. I have the high to low and low to high shift relays and wiring, the selector switch from the dash.
I know that powering up the relays will shift the transfer case, but the GEM module tells when the relays need to shut off, and that is where I am not sure what to do. I am assuming that the other plug on the shift motor (6 pin plug) is the sensor that tells the GEM module where the shift is at.
What needs to be done (with a bank of relays).....
View 10 Replies
Need a wire diagram. I have a connector in the cab that has red,blue,lt green,white wires. It's causing my brake lights not to work. I need a wire diagram that shows were they go. I can't find these wires in my Haynes manual.
View 3 Replies
I am trying to add courtesy lights to the existing reflectors in the front doors of my supercab. I can't find a wiring diagram that shows where to connect the light sockets. 1999 F250 SD...
View 2 Replies
I have a 2008 Ford F-150 xlt with stock instrument cluster. I need a new instrument cluster due to my interior lights coming on while driving. I would like to make it look better and not go stock. Id like to have digital shift screen and good looking LED's. What all are my options?
View 2 Replies
I'm trying to find the wiring diagram for the power windows in a 96 f150. I've got a set of these that i need to fab a harnes for to install in my 82.
View 12 Replies
Where can I find/buy a wiring schematic for a 2012 Ford E350 with the 5.4 L V8?
View 1 Replies
The instrument cluster in my 2005 Mountaineer has been randomly "failing" for about 2 months. By "failing", I mean the gauges will go to zero and bounce, the dash lights will go on and off, and the radio will go out. The car will continue driving normally. Headlights stay on, windows work, cruise works, interior lights work. This random event lasts about 4 seconds. It may do it again within minutes, or not again for the day. Sometimes, when I open the car door to get in (keys not in ignition), I will notice the gauges are bouncing at the zero mark. I took it to the shop, but of course it didn't do it there. They checked the alternator and battery. Battery is old, but checked out. A few weeks later, complete Alternator failure. Replaced the battery and alternator and I hoped that would solve the dash issue, but it did not. I've had it to the dealership, and to an independent, and their not sure what's up with it. The code readers give no insight.
View 8 Replies
I am currently converting a 1999 E350 7.3 diesel bus into a camper to live in. The bus has already had a lot of weird custom work. Done by someone else and a lot of the interior torn out and extra insulation put in. There is an exposed electrical panel behind the drivers seat. It was a cheap buy, previously fleet maintained with only 120k.
I was hooking up a battery for accessories to a terminal labeled "Battery" that does run indeed directly to the + terminal of the battery in the engine compartment.
Unfortunately I mistakenly connected the accessory battery to a terminal labeled "ignition" that runs to behind the dash. When I tried starting the vehicle off the auxiliary battery for a test everything went out for 2 seconds, I heard a click from the engine compartment, and everything than came back on. This is when I realized my mistake.
It used to be the speedo only didn't work (which I assumed was the step motor), now after this mistake all the gauges, the odometer and the buzzers don't work. Lights like the battery and airbag warning indicator still function.
Checked fuse 2 (15 amp) for the instrument cluster and it is intact. Actually checked every fuse in the vehicle in both fuse panels and all are intact. The radio works though and the vehicle is not equipped with power windows.
Going to go get a radio removal tool to take apart the dash and get back there. What this could be? Did I fry a relay? Did I fry the cluster circuit board.
View 6 Replies
I have a 2003 F550 6L diesel flatbed truck. Last week, the overdrive button would activate by itself. I'm assuming there was a loose wire so I taped the button to keep the overdrive off. Two days later, the overdrive came on while the button was pressed in and then smoke came out of the steering column/lever area. I pulled over and turned off the truck. The smoke stopped after 10 seconds and I restarted the truck. The overdrive light/functionality no longer worked and the instrument cluster also wasn't working.
The next day I was driving, and the truck died at a stoplight. I got it towed home, and opened the steering column and noticed that the overdrive button wire had burned. I removed the harness clip and charged the batteries. It started but the instrument cluster still didn't work. 2 minutes later the truck died. I replaced the alternator but still it won't charge the batteries. The truck dies 2 mins after getting a battery boost to start the truck. The instrument cluster also doesn't work. What could be causing this issue?
View 10 Replies
Im installing a set of 04 lariat seats into a 00 truck. I need to know how to hook up the heat. The power part is no problem. What I thought was right which was a separate constant 12v and a switched 12v for the module and ground apparently isnt right. If somebody could ohm out their harness on a 01 truck that would be great. As I have it right now the light on the switch comes on but almost instantly turns off.
View 14 Replies
Only numbers 1,2,5 match the diagram below. my 6,7,8 are BK/W, PK/B, BR/PK. My Sony CD player came with bare wires. So I could cut off the truck oem plug. How hard is it to find a plug that goes from my OEM plug to my Sony CD player?
View 10 Replies
I posted earlier about the tranny in my 01 Ex v10 having a transmission problem. The show looked at it and found the O2 sensor had shorted out and in some way sending the truck in to limp home causing the tranny fuse to blow????
Any way they fixed it or so they said and I drove it for a few hours and it did fine. The next morning I drove it and it blew the fuse. (under hood box I belive #19) I took it back to the shop and they beat and banged on it....got it wet etc. and can not get it to do it again. I know whe have an electrical issue but what all runs off of the fuse that controlls the tranny?
Is there any online wiring diagrams of excursions or superduty drive trains? Where all to look for the problem?
View 4 Replies
03 F250 Instrument panel does not work. Have checked all fuses with a meter. Have already fixed broken wires from the OD button on shifter handle. and also the alternator is not charging. I need wiring diagram that shows the wires coming out the back of the fuse box so I can see if the fuse holder is burned out......
View 8 Replies
For about 3 months, my wife's 2003 explorer has had a bad door sensor (I'm guessing). The car claims a door is ajar and the alarm would go off randomly if it's locked. Yesterday the battery died because apparently the alarm had been going off for so long while she was at work. After having a stranger jump it, she has had major problems:
-She claimed the headlights didn't work in any setting except in the on position with high beams on, but now they seem to work.
-The instrument panel is totally out including all gauges and all lights
-the power windows don't work
-the radio won't turn on or show any display
-the interior lights won't turn on
All of the fuses are fine and my mechanic checked them as well. He did say that a few key fuses aren't getting any power to them on either side. But the battery is charging and drawing just fine. The car doesn't seem to have any other issues and all of the flashers work just fine.
What the problem could be? I have wondered if one of the relays is busted.
View 3 Replies
I pumped gas at the local Chevron after noticing I was running just below a quarter tank this morning and immediately after turning the truck back on the instrument panel was dead. All other electric components worked fine (windows, headlights, signals, radio, etc.) Yukon GMC 2003 110k miles...
View 8 Replies
I plan on moving the engine/drivetrain from my 1986 F350 460 to my 1996 F250. I also want to move over the 1986's ignition system with a Duraspark 2 setup.
Although I could just cut in the easiest places to remove the wiring for later reuse I am looking for where to make the cuts, what to take and what to scrap. Alternatively I am also asking if there are aftermarket or OEM replacement sets out there are aren't a ton of money. The current harness in the 1986 has been sprayed with engine oil and cooked for 27 years so I am looking at alternative options if there are any.
View 8 Replies
I have a 97 F250 HD. Wiring the rear tail lights. When we bought it the had cut off the wires going to both sides of the rear lighting assemblys and I was wondering what wire went to what i have the left turn signal working just can't seem to get the brake/back up light to work on that side and i can't figure out how to get the right side going either.
View 8 Replies
