Ford Wiring/Electrical :: 2004 - Installing Seat - Wiring And Functions?
Mar 22, 2011
Im installing a set of 04 lariat seats into a 00 truck. I need to know how to hook up the heat. The power part is no problem. What I thought was right which was a separate constant 12v and a switched 12v for the module and ground apparently isnt right. If somebody could ohm out their harness on a 01 truck that would be great. As I have it right now the light on the switch comes on but almost instantly turns off.
View 14 Replies
Advertisement
Looking for a source for a wiring diagram for the 2003/4 f350 instrument cluster, specifically the wiring/connectors to the gauges? A link to a PDF file would be nice. I would like to try and disconnect the PCM control to the transmission temperature and engine temperature and drive the gauges from my own sensors to bypass the non-linear behavior that ford decided was in our best interest. I am NOT interested in installing any more gauges, just want to control the ones already present with my own signals. It is possible that these gauges are all addressable devices on a common bus, instead of individual controls.
View 8 Replies
I am a beginner when it comes to anything involving wiring. I am looking to re-wire all of the wiring coming off of the instrument cluster gauges. Once I have completed all of the wiring on the gauges, I may feel confident to move onto something else. As of rite now, it appears as though my truck is still running on all of the original wiring, and over the past few weeks, I have been having many wiring related issues. I found a schematic that includes the wiring for the gauges that I am going to go off of. I have a couple of questions before I begin.
1.) On the schematic, it shows connectors such as "Connector G" which is moving all of the gauges wires to there locations. Do I need to use a specific Ford connector, or could I purchase a new connector at any hardware store that carries them? As far as I am concerned, connectors do the same thing as all other connectors. (Let you connect and disconnect for easy instrument cluster removal.)
2.) I am not looking to purchase one of those expensive wiring harnesses. I would like to just purchase some wire that I can cut / use myself. What brand / type of wire should I be looking to purchase? I do not care if it is striped / colored as I will use wire tabs to name / label each wire.
Other than that, I feel confident enough to attempt something such as this. Here is the wiring schematic I am going to use.....
View 10 Replies
Any COMPLETE headlight switch wiring diagram? Everything I find online only shows 2-3 wires in each sub connector, nothing with all wires and colors, and what they do. and of course the factory service manuals no longer work on my new computer. the switch and associated wires went up in smoke 2 hours ago, and this truck is my only means of transportation rite now. what i need is headlight wiring with colors so i can temporary hook up a toggle switch to have lights until the new switch and connectors come in next week. I went to pull the switch and connectors out of the parts truck, but of course that does not have fog lights so it uses different switch and connections.
View 14 Replies
I plan on moving the engine/drivetrain from my 1986 F350 460 to my 1996 F250. I also want to move over the 1986's ignition system with a Duraspark 2 setup.
Although I could just cut in the easiest places to remove the wiring for later reuse I am looking for where to make the cuts, what to take and what to scrap. Alternatively I am also asking if there are aftermarket or OEM replacement sets out there are aren't a ton of money. The current harness in the 1986 has been sprayed with engine oil and cooked for 27 years so I am looking at alternative options if there are any.
View 8 Replies
I have a 97 F250 HD. Wiring the rear tail lights. When we bought it the had cut off the wires going to both sides of the rear lighting assemblys and I was wondering what wire went to what i have the left turn signal working just can't seem to get the brake/back up light to work on that side and i can't figure out how to get the right side going either.
View 8 Replies
Just bought an 04 Super duty with the factory plug 7pin and 4 pin plug. Checked the fuses and finally tracked down the 2 relays under the hood but can't seem to find anything wrong. Everything on the trailer works except for the running lights. Is there another fuse or something I have missed? Trailer works fine on my buddies Duramax and worked fine on my old 97.
View 14 Replies
Looking for a wiring diagram for a F-150 XLT LARIAT 5.8L 4BBL, all the books I have looked at show the wiring for this year with fuel injection and this truck came with a 351W with a Holley 600 4BBL, I have a few wire's in the engine compartment that melted away all the insulation, they are located close to where the harness passes the firewall before the ignition module. Is this a common problem on old models ?. Need a clear copy of the correct diagram for a f-150 1987 with carburetor, how I can get a copy so I can fix this problem before it gets worse.
View 3 Replies
Let me start by saying electrical is something I really have no knowledge of....(never used any kind of an elec meter and don't have one) simple, Pos-grd and fuse, NP. I really don't want to fry something in these expensive new seats w/my normal trial and mostly ERROR!
The 08 (drivers) seat has 4 wires in the input clip.
GRN-RED (heavy gauge)
BLK-PURP (heavy gauge
BLU-RED
BLK-WHT
and my 01 whip out of the floor has a 3 wire setup.
GRN (heavy gauge)
BLK (heavy gauge)
BRN-BLU
I can wire PS side seat from fuse box and ground it NP. It only has a 2 wire set-up in the new seat.
View 1 Replies
I am curious if it is possible to make a stand alone controller for the electric shift transfer case in a 2000 F-350?
The reason I ask is, this is swapped into a 4x4 conversion in a van and I would like the transfer case to work like the factory, but I don't want to swap over the whole GEM module. I have the high to low and low to high shift relays and wiring, the selector switch from the dash.
I know that powering up the relays will shift the transfer case, but the GEM module tells when the relays need to shut off, and that is where I am not sure what to do. I am assuming that the other plug on the shift motor (6 pin plug) is the sensor that tells the GEM module where the shift is at.
What needs to be done (with a bank of relays).....
View 10 Replies
Need a wire diagram. I have a connector in the cab that has red,blue,lt green,white wires. It's causing my brake lights not to work. I need a wire diagram that shows were they go. I can't find these wires in my Haynes manual.
View 3 Replies
I am trying to add courtesy lights to the existing reflectors in the front doors of my supercab. I can't find a wiring diagram that shows where to connect the light sockets. 1999 F250 SD...
View 2 Replies
I'm trying to find the wiring diagram for the power windows in a 96 f150. I've got a set of these that i need to fab a harnes for to install in my 82.
View 12 Replies
Looking for wiring diagram for the older Ford cruise control switches. I'm wanting to add an aftermarket system but use the factory switches. It's for a 99 ranger with the steering wheels like the mark 8s, older mustangs, explorers, and many others, had.
View 1 Replies
Where can I find/buy a wiring schematic for a 2012 Ford E350 with the 5.4 L V8?
View 1 Replies
I just bought a hard to start 1990 F250. Per the board, just replaced all 8 glow plugs with Motorcraft. Still wouldn't start (it turns over but will only start if you use either). I attempted to install a new BWD brand (Borg Warner I believe) glow plug connector relay today...I removed the old no problem, but am unsure what wires to plug where....the only connection that I'm sure about is the blue wire that works the WTS feature...it plugs in easily but I don't know if there are other connections that need to be made or not? All the wires run from the posts and into the bottom of the unit.
View 2 Replies
What I am trying to do it put in 2 led spot light for added backing up light. What i want to do is have them turn on when put into reverse but also have a switch i can use to turn them on when not in reverse. Just need to know what relay I need and if it even can be done.
I was also thinking of just taping into the wiring harness and adding a wire that goes to the spot lights and another wire that goes to a switch that I could turn on and supply power to the light when not in reverse (I know it will light the revers light also) but is it ok to do that?
View 5 Replies
I have a 2002 excursion XLT. it does not have power seats for the driver or passenger. I came across some power seats from a 2002 limited. what I need to know is, can I remove the non power seats and put in the seats from the limited, is the wiring already in the XLT model to just plug it in, or im I going to have to do some rewiring.
View 2 Replies
My Ranger, an '04 Edge without cargo lights. The high mount stoplight is faintly lit with the parking/headlights on. I had changed out the incandescent bulb for a LED, and went out to see how everything looked after dark. Well, the high mount had a slight glow to it, not really on, just a faint glow. This was never noticed with the regular bulb. I suspect I may have some stray voltage coming from somewhere, just enough to make the LED glow, but not enough for the normal bulb. When I switched off all the lights, it went out as well.
I tried to find a wiring diagram on line, like I've suggested to others in the past, but no luck from Autozone, or the EBSCO host I've used before. In fact the EBSCO will no longer accept "tech" as a user name or password.
So, where the problem may lie? I hate it when I can't figure out something like this!!!
View 6 Replies
I have a 04 explorer I have been trouble shooting and the master switch works all but the passenger window wont work it at all but all the others work fine, its not the switches replaced both, the passenger window switch will roll the window down but not back up. I checked for power there is power to the switch in the passenger side, the ground is good. I can pull the plug off the motor and hook a jumper ground up and the switch will make it go back up. I have been working in body shops for 40 years and now this is the first one to stump me
View 7 Replies
My 2004 expedition wont go into any gear the shifter will not move I changed the stop light brake switch and a 30 amp buss fuse I found blown and also the check engine light is on now too this was after I parked it I also changed a 30 amp buss fuse I found blown out but it still don't work the only way I can get it into gear is to push the little button under steering wheel...
View 2 Replies
