I discovered today that I have no brake lights on my '02 Excursion. The center brake light works fine, but the two in the taillights don't come on. Stopped and bought new bulbs on the way home and replaced both, but the ones I pulled out were not blown. Checked the fuse - OK. Taillights and turn signals both work fine.
View 3 Repliesmy 79 Bronco tail lights only are stuck on with the key on? the brake lights and blinkers and headlights work fine and (all the running lights) work fine when turned on, but with all the switches off and key on only my tail light running lights stay on?
View 14 RepliesMy brake lights don't work. Turn signals, tail lights, hazard flashers work, but if I hit the brake, nothing happens. What could possibly be the problem? Could there be a wiring issue?
View 7 RepliesI did lower the steering column, onto the seat. Also lowed the dash and the wiring. Does it sound like the Multifunction switch could be bad? I can put it in drive, so I don't think it's the brake light pedal switch, that's bad.
View 14 Repliesi have an 85 f150. the brake lights are not working. i checked the bulbs, both filiments are working. i have running lights, turn signals, and hazards, just no brake lights. i am confused as to why i have everything else except brake lights. need to figure out what to do next to figure this out.
View 14 RepliesFirst off my driver side brake light with stop working. I took it apart to try and find the short. In the process I shorted out all my running lights tail lights and brake lights and turn signals I think also. While I was looking for the short, turn signal wire from my tail light touched the frame and grounded out and that's when all the lights died . My tail lights are some cheap trailer lights without reverse lights. I pulled headlight switch from another Ford truck I have. On the harness connector that connects to the switch which wires should read what when I test with a voltmeter?I checked the fuses in the power distribution box under the hood and they were good. Truck has a flat bed so I don't know if that matters with the wiring, I suspect it's different then a normal bed truck. Wiring on the bed is old, maybe from 94. I am unexperienced with electrical.
View 3 Replies85 ford ranger 2.3 efi .. My brake lights still aren't coming on. According to the Haynes manual, the wire that runs from the stop light fuse goes from there to the hazard flasher and then to the brake light switch. Since I have checked everything else, is it possible that the hazards are causing a break in the connection?
View 4 RepliesI have no left rear signal or brake lights. The right side works fine and both left/right tail lights work fine, just no left brake or signal. I checked for broken wires and can not find anything. 1992 Ford E50 7.5L.
View 1 RepliesI just bought my first Ford its an 1996 f250 powerstroke, and I am having issues with it. Every time I push in the brake both blinkers come on and tail lights and upper parking lights on cab, and when I turn on a blinker everything flashes.
View 8 RepliesSo I recently bought a 1997 7.3l F250. It is in fairly good condition, but it has some problems with the lights working. The turn signals and hazards all work, as do the tail lights and headlights. However, when I hit the high beam switch, the headlights cut off entirely. Also, the brake lights do not work at all. Ive checked the bulbs and since they all work Im not sure what the issue is.
View 3 Replies1991 F250 Supercab Diesel 4X4. I made a mistake while wiring up my trailer lights and ended up grounding out my brake controller, frying it. Along with that, I popped a couple fuses as well (1, 5 and 9 I believe). Replaced all fuses and got my signals (F/R) back at least.
Here's what's NOT working/messed up:
*Brake Lights
*Cruise Control
*Rear ABS light comes on a few minutes after driving.
*Front hazards work, not rear. When I apply the brake, the hazards pause in the on position.
I've tested the brake switch on the brake pedal (Green/Red and Green) and it works properly. So, current is obviously not reaching the rear brake lights.
Another note. The truck is wired with a 7 pin plug in the bed for a goose neck trailer. It also was wired to a 6 pin on the bumper. I replaced the 6 pin with a 7. The signal/brake pins on the plugs (both) and also not receiving power. What's the next thing to check?
My brake lights, turn signals, and flasher are not working in my truck. Is it a fuse and what fuse? Could it be a relay?
View 2 RepliesDad borrowed truck and wired 7 pin trailer harness. Lights worked on truck/trailer for use but upon return the turn signals didnt work. Hazards and running and brake lights did work. Replaced TS flasher and Haz flasher. Still no signals. Pulled steering wheel and replaced turn signal cam only, not whole switch. Now no brake lights, no rear hazards or turn signals. Losing my marbles trying to follow schematic and using test light and mulit meter. All bulbs and fuses are good. Running lights and head lights working as well.
View 6 RepliesI just bought an 05 F250 XLT. I noticed tonight that the rear turn signals and brake lights don't work.
The front turn signals work fine, although they flash fast. I know that usually means a light on its way out. neither taillight flashes though, which puzzles me.
My second issue is that, of the 3 brake lights, only the high mounted light illuminates when I hit the brakes.
What I am trying to do it put in 2 led spot light for added backing up light. What i want to do is have them turn on when put into reverse but also have a switch i can use to turn them on when not in reverse. Just need to know what relay I need and if it even can be done.
I was also thinking of just taping into the wiring harness and adding a wire that goes to the spot lights and another wire that goes to a switch that I could turn on and supply power to the light when not in reverse (I know it will light the revers light also) but is it ok to do that?
I am working on friends 2011 Ford F450 Diesel He has lost Brake Lights and Turn Signal/Hazards.
Turn signals work in front of truck. Running lights are working fine.
Same goes when trailer is connected on truck. What could be the problem.
Need a wire diagram. I have a connector in the cab that has red,blue,lt green,white wires. It's causing my brake lights not to work. I need a wire diagram that shows were they go. I can't find these wires in my Haynes manual.
View 3 RepliesAny COMPLETE headlight switch wiring diagram? Everything I find online only shows 2-3 wires in each sub connector, nothing with all wires and colors, and what they do. and of course the factory service manuals no longer work on my new computer. the switch and associated wires went up in smoke 2 hours ago, and this truck is my only means of transportation rite now. what i need is headlight wiring with colors so i can temporary hook up a toggle switch to have lights until the new switch and connectors come in next week. I went to pull the switch and connectors out of the parts truck, but of course that does not have fog lights so it uses different switch and connections.
View 14 RepliesI have a 97 F250 HD. Wiring the rear tail lights. When we bought it the had cut off the wires going to both sides of the rear lighting assemblys and I was wondering what wire went to what i have the left turn signal working just can't seem to get the brake/back up light to work on that side and i can't figure out how to get the right side going either.
View 8 RepliesJust bought an 04 Super duty with the factory plug 7pin and 4 pin plug. Checked the fuses and finally tracked down the 2 relays under the hood but can't seem to find anything wrong. Everything on the trailer works except for the running lights. Is there another fuse or something I have missed? Trailer works fine on my buddies Duramax and worked fine on my old 97.
View 14 RepliesI got my Alternator replaced last week. Last night, I hit a very small bump, not even large enough to really cause me to slow down, and as soon as I did, my battery and brake lights came on. My RPM gauge also jumped around and eventually went to 0 until I stopped and put the car in park. (The bump might just be a coincidence who knows). So after all this happened, I turned off my car, tried to restart and got nothing. Sometimes I get a click, sometimes 2 clicks up to 4-6 consecutive clicks. Every few times I won't even get a click, just a slight attempt to start, then the car dies, then 2 seconds later all my lights and radio etc. come back on. My problem here is a few things:
1. I've been told it could be the starter. If it's the start, those dashboard lights shouldn't have came on right? just the STARTING portion of the car.
2. I've been told it could be the battery.
Well If i got my alternator tested and Advance said it was working, Why would my battery be dead? And if it WAS dead, wouldn't my lights have went dim or something else happen to the car?