Ford Wiring/Electrical :: 2002 - Complete Headlight Switch Wiring Diagram?
Apr 29, 2013
Any COMPLETE headlight switch wiring diagram? Everything I find online only shows 2-3 wires in each sub connector, nothing with all wires and colors, and what they do. and of course the factory service manuals no longer work on my new computer. the switch and associated wires went up in smoke 2 hours ago, and this truck is my only means of transportation rite now. what i need is headlight wiring with colors so i can temporary hook up a toggle switch to have lights until the new switch and connectors come in next week. I went to pull the switch and connectors out of the parts truck, but of course that does not have fog lights so it uses different switch and connections.
View 14 Replies
Advertisement
Looking for a source for a wiring diagram for the 2003/4 f350 instrument cluster, specifically the wiring/connectors to the gauges? A link to a PDF file would be nice. I would like to try and disconnect the PCM control to the transmission temperature and engine temperature and drive the gauges from my own sensors to bypass the non-linear behavior that ford decided was in our best interest. I am NOT interested in installing any more gauges, just want to control the ones already present with my own signals. It is possible that these gauges are all addressable devices on a common bus, instead of individual controls.
View 8 Replies
Looking for a wiring diagram for a F-150 XLT LARIAT 5.8L 4BBL, all the books I have looked at show the wiring for this year with fuel injection and this truck came with a 351W with a Holley 600 4BBL, I have a few wire's in the engine compartment that melted away all the insulation, they are located close to where the harness passes the firewall before the ignition module. Is this a common problem on old models ?. Need a clear copy of the correct diagram for a f-150 1987 with carburetor, how I can get a copy so I can fix this problem before it gets worse.
View 3 Replies
I am curious if it is possible to make a stand alone controller for the electric shift transfer case in a 2000 F-350?
The reason I ask is, this is swapped into a 4x4 conversion in a van and I would like the transfer case to work like the factory, but I don't want to swap over the whole GEM module. I have the high to low and low to high shift relays and wiring, the selector switch from the dash.
I know that powering up the relays will shift the transfer case, but the GEM module tells when the relays need to shut off, and that is where I am not sure what to do. I am assuming that the other plug on the shift motor (6 pin plug) is the sensor that tells the GEM module where the shift is at.
What needs to be done (with a bank of relays).....
View 10 Replies
Need a wire diagram. I have a connector in the cab that has red,blue,lt green,white wires. It's causing my brake lights not to work. I need a wire diagram that shows were they go. I can't find these wires in my Haynes manual.
View 3 Replies
I am trying to add courtesy lights to the existing reflectors in the front doors of my supercab. I can't find a wiring diagram that shows where to connect the light sockets. 1999 F250 SD...
View 2 Replies
I'm trying to find the wiring diagram for the power windows in a 96 f150. I've got a set of these that i need to fab a harnes for to install in my 82.
View 12 Replies
Where can I find/buy a wiring schematic for a 2012 Ford E350 with the 5.4 L V8?
View 1 Replies
Looking for wiring diagram for the older Ford cruise control switches. I'm wanting to add an aftermarket system but use the factory switches. It's for a 99 ranger with the steering wheels like the mark 8s, older mustangs, explorers, and many others, had.
View 1 Replies
I have a 2000 E150 (Glavel Conversion) van and the interior lights do not illuminate when the doors are opened, although they used to. They also no longer turn on from the headlight dimmer switch. They will turn on individually if the manual switch at each light is pressed while the engine is running, so the bulbs and wiring appear to be working. I replaced the headlight switch with no noticeable effect. Is there a timing circuit that switches these on for a short period of time to allow illuminated entry that could have failed? If so, where would I find the module and how would I test? Relays and fuses look good.
View 1 Replies
Looking for the wiring diagram for the 4X4 switch that is connected to the back on of the coin holder on a non-4X4? It is an 8 pin plug but only has 5 wires connected to it on my 2012. Can you get 12V switch power here?
View 2 Replies
Only numbers 1,2,5 match the diagram below. my 6,7,8 are BK/W, PK/B, BR/PK. My Sony CD player came with bare wires. So I could cut off the truck oem plug. How hard is it to find a plug that goes from my OEM plug to my Sony CD player?
View 10 Replies
Looking for a pic of the headlight plug wiring diagram?? I have the B5.5 lights, I don't know if that makes a difference. I need it for my latest retrofit.
View 1 Replies
I posted earlier about the tranny in my 01 Ex v10 having a transmission problem. The show looked at it and found the O2 sensor had shorted out and in some way sending the truck in to limp home causing the tranny fuse to blow????
Any way they fixed it or so they said and I drove it for a few hours and it did fine. The next morning I drove it and it blew the fuse. (under hood box I belive #19) I took it back to the shop and they beat and banged on it....got it wet etc. and can not get it to do it again. I know whe have an electrical issue but what all runs off of the fuse that controlls the tranny?
Is there any online wiring diagrams of excursions or superduty drive trains? Where all to look for the problem?
View 4 Replies
I just picked up my 2007 F350 as a replacement for my 2003 F350 (still have the 2003). I really like the uplifter switch option on the truck, I can normally figure things out but I am one of those people who is electrically challenged (home and auto)and also am one who does not wish to butcher the new ride (same for the home)to gain an education in the art of wiring. I would like to reinstall my headache rack lights on this truck as they are needed for winter work. I was in my truck manual and the info for wiring is weak and the website did not respond nor did my email to ford. I have found the wire harness but it is not tagged as a pair/color to switch. I have the lights already grounded to the rack, so I am thinking I just need the hot wire from the switch. Looking for the color code for positive and ground for the switches.
View 14 Replies
I am actually looking for the wiring diagram for the plug that connects to the headlight/turn signal stock. I have tried the service website, but I can never seem to find what I am looking for on there.
View 13 Replies
I am a beginner when it comes to anything involving wiring. I am looking to re-wire all of the wiring coming off of the instrument cluster gauges. Once I have completed all of the wiring on the gauges, I may feel confident to move onto something else. As of rite now, it appears as though my truck is still running on all of the original wiring, and over the past few weeks, I have been having many wiring related issues. I found a schematic that includes the wiring for the gauges that I am going to go off of. I have a couple of questions before I begin.
1.) On the schematic, it shows connectors such as "Connector G" which is moving all of the gauges wires to there locations. Do I need to use a specific Ford connector, or could I purchase a new connector at any hardware store that carries them? As far as I am concerned, connectors do the same thing as all other connectors. (Let you connect and disconnect for easy instrument cluster removal.)
2.) I am not looking to purchase one of those expensive wiring harnesses. I would like to just purchase some wire that I can cut / use myself. What brand / type of wire should I be looking to purchase? I do not care if it is striped / colored as I will use wire tabs to name / label each wire.
Other than that, I feel confident enough to attempt something such as this. Here is the wiring schematic I am going to use.....
View 10 Replies
I plan on moving the engine/drivetrain from my 1986 F350 460 to my 1996 F250. I also want to move over the 1986's ignition system with a Duraspark 2 setup.
Although I could just cut in the easiest places to remove the wiring for later reuse I am looking for where to make the cuts, what to take and what to scrap. Alternatively I am also asking if there are aftermarket or OEM replacement sets out there are aren't a ton of money. The current harness in the 1986 has been sprayed with engine oil and cooked for 27 years so I am looking at alternative options if there are any.
View 8 Replies
I have a 97 F250 HD. Wiring the rear tail lights. When we bought it the had cut off the wires going to both sides of the rear lighting assemblys and I was wondering what wire went to what i have the left turn signal working just can't seem to get the brake/back up light to work on that side and i can't figure out how to get the right side going either.
View 8 Replies
Just bought an 04 Super duty with the factory plug 7pin and 4 pin plug. Checked the fuses and finally tracked down the 2 relays under the hood but can't seem to find anything wrong. Everything on the trailer works except for the running lights. Is there another fuse or something I have missed? Trailer works fine on my buddies Duramax and worked fine on my old 97.
View 14 Replies
Im installing a set of 04 lariat seats into a 00 truck. I need to know how to hook up the heat. The power part is no problem. What I thought was right which was a separate constant 12v and a switched 12v for the module and ground apparently isnt right. If somebody could ohm out their harness on a 01 truck that would be great. As I have it right now the light on the switch comes on but almost instantly turns off.
View 14 Replies
