I have a '99 psd f250 crew cab lariat, I just purchased seats from a 2005 F350 that are lariat heated and power. My seats are power but non heated is there a way to hook everything up.
View 3 RepliesLet me start by saying electrical is something I really have no knowledge of....(never used any kind of an elec meter and don't have one) simple, Pos-grd and fuse, NP. I really don't want to fry something in these expensive new seats w/my normal trial and mostly ERROR!
The 08 (drivers) seat has 4 wires in the input clip.
GRN-RED (heavy gauge)
BLK-PURP (heavy gauge
BLU-RED
BLK-WHT
and my 01 whip out of the floor has a 3 wire setup.
GRN (heavy gauge)
BLK (heavy gauge)
BRN-BLU
I can wire PS side seat from fuse box and ground it NP. It only has a 2 wire set-up in the new seat.
I am trying to add courtesy lights to the existing reflectors in the front doors of my supercab. I can't find a wiring diagram that shows where to connect the light sockets. 1999 F250 SD...
View 2 RepliesI have an 2002 F250 super duty that has leather seats. The seats are power but not heated. I bought seats out of a Harley Davidson edition that are electric and heated. They have an extra plug that my truck don't have. How can I make the seat heaters work?
View 4 Replies1999 - F250 7.3L Crew/Longbed manual locks/windows ...
2x New Batteries a few days ago, same symptoms as old batteries ...
Sitting overnight loses .1 volt due to cooler temps in am measurement:
9pm 12.92v
7am 12.83v
11am 12.93v*
*won't start
The amp draw measured at 9pm and 11am is essentially zero (reading .06 or less, usually 0.00) on both cables exiting the passenger side battery. This is sitting for an hour plus with the hood courtesy bulb removed. (although it drops to near zero within a few minutes of the domes going off). Using a clamp around ammeter.
The alternator is charging (14+v reading while driving). When trickle charged overnight the truck starts fine. Plugging in the block heater makes no difference in starting (or not). 45 F overnight. When it doesn't start:
-double keying the glow plug light comes on
-tach needle bounces on crank
-voltage of 12.8 drops to 11.2 on glow plugs, then 10, then 7 while cranking
-sounds like it's almost going to catch, then bogs hard and the voltage really drops
Again, it starts fine when charged and starts after short trips (by virtue of my wife having made it home). Haven't tried to jump start as I don't have anything handy that is boss enough to jump one of these. Typical use during failure:
Charging with charger
Start
30 min to store
3 stores, start 3 times
30 min to home
Sit overnight
Won't start
This morning I checked that the battery terminals and battery clamps all had the exact same voltage. There are occasionally amps between the batteries (.37 to .08) measured on each end of the cable going over the radiator.
So, if there is no drain and the block heater doesn't work, but it starts fine if it hasn't been driven/sitting, what is next to check?
I have an early 99 F250. The a/c compressor stopped working. Have checked pressures, switches, freon etc. Found the switch in the dash is not getting power to send to the compressor. Where the feed for this switch is? I have checked all fuses, all good. The manual does not show a relay as being an a/c relay, so I am stumped without taking it somewhere now but I would like to avoid that.
View 7 RepliesI have a 99 F250 super duty 4x. It's all stock except for some speakers I replaced when I got it. The others were blown from my uncle. I don't have any amp or anything like that and the truck has ran fine for 3 years so I don't think the alternator has failed because of that. I'm thinking just age and 138k miles.
I was wondering what generation of alternator might be on there and how to tell the difference between the generations.
I have 12.5V with the truck off, about 14V with it on idle. As soon as I get it around 3000 RPM the battery light comes on and the voltage goes to 12.5V. Where can I get a rebuild kit for the alternator. I don't see anything at the major parts shops (napa, oreilly, autozone). Could this be the voltage regulator(that I did see at the stores)? I think its mounted to the back of the alternator. Is there any way to test the alternator further?
I'm a little confused as why it would be only above 3000 rpm. Are there two separate circuits for it? Like a low rpm one and then a different one above 3000 rpm?
I have a 97 F250 HD. Wiring the rear tail lights. When we bought it the had cut off the wires going to both sides of the rear lighting assemblys and I was wondering what wire went to what i have the left turn signal working just can't seem to get the brake/back up light to work on that side and i can't figure out how to get the right side going either.
View 8 RepliesI just bought a hard to start 1990 F250. Per the board, just replaced all 8 glow plugs with Motorcraft. Still wouldn't start (it turns over but will only start if you use either). I attempted to install a new BWD brand (Borg Warner I believe) glow plug connector relay today...I removed the old no problem, but am unsure what wires to plug where....the only connection that I'm sure about is the blue wire that works the WTS feature...it plugs in easily but I don't know if there are other connections that need to be made or not? All the wires run from the posts and into the bottom of the unit.
View 2 RepliesI have a 2002 excursion XLT. it does not have power seats for the driver or passenger. I came across some power seats from a 2002 limited. what I need to know is, can I remove the non power seats and put in the seats from the limited, is the wiring already in the XLT model to just plug it in, or im I going to have to do some rewiring.
View 2 RepliesBlower, seats, locks, blinkers stopped simultaneously, abs and airbag light came on. The internet suggested it was the ignition switch, I changed it to no avail. The horn, wipers, 4-way flashers, headlights, taillights, and brake lights all work. Is my wife correct in suggesting we replace this 140,000 mile pile of rust?
View 5 RepliesI have a friend of mine that has a 1983 and he had me change the water pump in it because it started leaking and it has been sitting for 7 Months now. I changed that but I can't get this bugger to start. I used to be a mechanic in a past life so I know what I'm doing most of the time so let me explain what has transpired here.
I attached my remote starter, turned on the key and cranked over the engine after shooting a little bit of starting fluid in the carb and she cranks over but won't start. I then pulled the #1 spark plug out and then did the same thing to check for spark and nada. I put my light tester on the coil and there was power. I have run into this kind of problem years ago with other vehicles so I thought I would just go ahead and replace the Coil and also the Control Module. After replacing these parts, still no spark. Since the distributor is there only to distribute the spark (meaning no electrical connections to it) I'm assuming that the Pick Up part that is down by the Crank shaft might be bad.
How to test either the Control Module or the pick up. I'm trying to diagnose this problem without needing to remove the module and taking them to the parts house for testing. (long drive). These wires should have 12 volts when the key is off and these wires should have 12 volts when the key is on.... and so on.
I recently bought a 92 F250 and love it but the blinkers will not work. I have replaced both flashers and the multifunction switch. (the wipers had issues too that were fixed by the switch...) Now what? Im at a loss..
View 7 RepliesMy work truck is an 03 F250 5.3L. My flashers recently stopped working. I turn them on, and they will work anywhere from 5 seconds to a few minutes, then either blink rapidly and shut off, stay solid for a few seconds and shut off, or just shut off. I push the switch off and on again, and the cycle repeats. All my other lights and turn signals work fine with no issues.
This wouldn't be a huge issue, but where I work I need the flashers a lot. The truck has a bar light and siren/pa system wired into it, but not to the lights or anywhere near that. I can't say exactly how it's wired because I didn't install it, but I followed the wires and they don't go under the steering wheel where I would assume the relay and wires for flashers would be.
What sounds like is wrong? I wouldn't think it would be the relay because then I would think that I would be having problems with more than just the flashers. So I'm not sure if there would just be a ground issue or if it's the actual switch that turns on the hazards. Also, there are no lights that are burnt out.
I have a 1979 f-250 4x4 with a 351m. The problem I am having is my starter keeps running after the truck starts and also after I shut off the key. I didn't get the battery unhooked in time today and it completely melted the lug off on the solenoid, but the other wires were barley warm. What could be causing this problem? The battery is new, the cables are new and the Sol. was new. Maybe the switch or the starter?
View 8 RepliesI have a 1991 idi diesel f250. My dash lights have entirely gone out and i cannot seem to figure out why, i checked the fueses under the driver dash and under the hood for that matter and nothing is blown.
At the same time, the dome lights, door lights, cab lights, stereo, windows, ever the light in the ash trey etc, work perfectly fine. Could a wire have come loose behind the dash cluster and shorted out everything in the driver area?
I still get the high beam signal, check engine, engine, wait to start, and water in fuel light in the cluster. but no back lighting (when turning the key to the on position)...
2002 f250 v10 4x4. Truck will loose all power...
View 10 RepliesI have a '97 F250 diesel and the battery light keeps coming on and off. The volt meter shows a good charge. How do I fix this?
View 4 RepliesI have an 86 f250 i just bought back with no spark. this truck is not original. used to be a diesel. has a 400 out of 81 f250. had this truck running just fine 4 years ago. sold it to a guy running and bought it back 4 yrs later not running.
Checked all the connection to make sure they r clean. Had the ignition modular tested and tested good. I have 12+ volts from the white and red wire. I have a little over 6 volts at the bat side of the coil. I have no spark from the coil. I notice every time I connect and disconnected the bat cable I will get a spark from the coil. i ran a test light from the tack test sight on the coil and tried to start and the light stayed real dim and never flickered.
I bought a truck recently and I am attempting to get the alternator to charge. A previous owner hacked up the wiring pretty badly. We found that they had connected the voltage regulator to the horn relay for some reason. Anyway, I am trying to get it rewired and have searched existing threads for info and I thought that I had the wiring sorted out, however it is still not charging the battery.
The alternator has been tested and works. The voltage regulator is new. This is how it is currently wired.
Regulator A Terminal --> Battery side of started solenoid --> Alternator Batt Post
Regulator F Terminal --> Alternator Fld Post
Regulator S Terminal --> Alternator Sta Post
Regulator I Terminal --> Empty
Regulator body --> Radiator Support --> Alternator Ground Post --> Neg batt
When running, the battery is showing about 11.8 and slowly dropping as it runs. The truck has an ammeter in the dash, however it looks like it is no longer connected. Does it need to be connected in order for the alternator to charge the battery?
My indicator lights are all out. The turn signals work correctly, as do the dash lights themselves, but all of the warning lights are out. The truck sat for three years and I have just gotten it back on the road.
View 7 Replies