I have an early 99 F250. The a/c compressor stopped working. Have checked pressures, switches, freon etc. Found the switch in the dash is not getting power to send to the compressor. Where the feed for this switch is? I have checked all fuses, all good. The manual does not show a relay as being an a/c relay, so I am stumped without taking it somewhere now but I would like to avoid that.
View 7 RepliesSo I have an 04 F250 Super Duty 6.0L and suddenly the turn signals and hazards stopped working. First I replaced the switch on the steering column...no luck. Today I replaced the flasher relay under the dash panel (the blue one)...still no luck. I remember checking fuses in the fuse box but don't remember which ones I checked but I didn't see anything obvious. I also took a quick look under the dash at all the wires for any anomalies...nothing. I'm lost... What to do next!?
View 1 RepliesWe have a 1999 F-350 V10 super duty. The alt was over charging and the gauges stopped working. Replacing the alt, the guages still don't work, and the new thing is the charge light and selt belt light comes on. The fuses 29 (5amp)and 30(30Amp) which are supposed to be key on hot only are hot at the same time. With these on, it causes a drain killing the battery. Also if the truck is started, the lights go out, but when you try to turn the vehicle off, it stays running, one with the battery disconnected. The only way to shut it down is pull the fuse box power fuse, 50(amp)Some one had been in the dash before we got this vehicle and busted, burned out or removed the check engine light. I can read codes and their vehicle runs fair and does operate. Could this be a dash board? Also this problem appears when the truck is sitting, and the key removed nothing on. No fuses are blown either.
View 3 RepliesI am trying to add courtesy lights to the existing reflectors in the front doors of my supercab. I can't find a wiring diagram that shows where to connect the light sockets. 1999 F250 SD...
View 2 RepliesMy tail lights parking lights and dash board lights stop working my turning signals work my brake lights work and my headlights work fine I checked all fuses are good I even switched out the headlight switch with a new one and nothing. What can this problem be?
View 14 RepliesMy father in-law gave us a 1996 explorer AWD with a 5.0 for my son who is 16. A couple of weeks later he's out learning with my wife and a very strong electrical smell took over the cabin. They came right home and when I got in I found all of the gauges not working. The instrument lights work, blinkers work, but all gauges do nothing. Pulled cluster and wires look O.K. behind it from what I can see. They saw no smoke, just smell, fuses look O.K.. What could cook on this vehicle that would wipe out just the gauges?
View 5 RepliesI'm having a problem with my interior dome light and my door chime bell not working in my '01 F-250. I found that the bulb was blown,so I replaced it thinking it might fix the door chime bell also, thinking they were wired together from the factory.
The new bulb didn't fix the problem. I recall that when I noticed the door bell didn't ding-ding anymore was about the time(when it got dark), that I noticed the dome light was out also.
What I may check? The fuses all work, the interior dome relay switch works and I see nothing else in the owners manual to look for as far as dome lighting and door bell chime.
I have a new to me 2008 F250 XLT. Neither side on the power mirrors is working. The manual shows fuse number twelve on the passenger side fuse block is the one that controls this circuit. The fuse is good (continuity wise). What I need to know is what color is the wire that feeds power to the switch block on the driver's side door panel. Pulled it out of the door panel and wiring was intact and corrosion free. I need to find out if there is power there or is it an issue between the fuse block and the switch.
View 2 RepliesI have a 2005 excursion with about 112,000 miles and last week all 5 doors decided to stop working on me when trying to lock or unlock with the remote or the door switch. I do hear a sound like something is happening just right of the fuse box. I did a little research and found that this is a wide spread problem. I did order 4 of the 5 actuators and I replaced the drivers door but nothing yet. Do they all have to be replaced in order to work? Or is it most likely something else causing this? Just trying to figure it out before I install the other actuators or take it in to a shop.
View 1 RepliesI have an 89 f250 7.3. horn has not been working for the longest time the relay clicks but still nothing. It doesn't matter weather the key is in the on or off position. I know it might be a grounding problem because the cruise control does not work any more (even though recently it was working just fine). I didn't see any bad fuses.
View 6 RepliesI have a 2001 F250 with 7.3. We swapped the auto for a zf6 manual. We left the auto's shift position sensor tied to the frame and left in neutral. I did install a pcm from a manual transmission pickup. Also have the clutch position switch hooked up. I have an Edge Evolution CTS2 reprogrammer, and on the display the gear indication always shows P. I suspect that is why my cruise doesn't work. For interests sake, I tried manually adjusting the shift position sensor through all gears, and the reverse lights come on when in reverse but the Edge's display always shows P. My question is with a manual transmission, how does the pcm know that it is in gear? The only sensor that I am aware of is the reverse sensor on the zf6.
View 4 RepliesI have a 2000 Ford F250 lariat 7.3 .... This vehicle has an aftermarket double din stereo pillar gauges for Pyro meter and transmission temp and has also had a snowplow attached but since re moved since I purchased it. It also has H ID headlights, which are run by the passenger side headlight connection.
The problem I'm having is that whenever I turn on the parking lights it is blowing the number eight fuse under the hood. Which is giving me no dash lights running lights parking lights or taillights. Initially the fuse would last for a few minutes and then burn out. I should also add that the trailer wiring harness doesn't work either and the driver side headlight will work sporadically.
I have checked the fuses for the Hazard and the Turn Signals. Both look fine. I tried replacing the turn signal flasher (which was a task in itself). After all of this it is still not working. What else could it be? Simple short?
View 2 RepliesI have a '99 psd f250 crew cab lariat, I just purchased seats from a 2005 F350 that are lariat heated and power. My seats are power but non heated is there a way to hook everything up.
View 3 Replies1999 - F250 7.3L Crew/Longbed manual locks/windows ...
2x New Batteries a few days ago, same symptoms as old batteries ...
Sitting overnight loses .1 volt due to cooler temps in am measurement:
9pm 12.92v
7am 12.83v
11am 12.93v*
*won't start
The amp draw measured at 9pm and 11am is essentially zero (reading .06 or less, usually 0.00) on both cables exiting the passenger side battery. This is sitting for an hour plus with the hood courtesy bulb removed. (although it drops to near zero within a few minutes of the domes going off). Using a clamp around ammeter.
The alternator is charging (14+v reading while driving). When trickle charged overnight the truck starts fine. Plugging in the block heater makes no difference in starting (or not). 45 F overnight. When it doesn't start:
-double keying the glow plug light comes on
-tach needle bounces on crank
-voltage of 12.8 drops to 11.2 on glow plugs, then 10, then 7 while cranking
-sounds like it's almost going to catch, then bogs hard and the voltage really drops
Again, it starts fine when charged and starts after short trips (by virtue of my wife having made it home). Haven't tried to jump start as I don't have anything handy that is boss enough to jump one of these. Typical use during failure:
Charging with charger
Start
30 min to store
3 stores, start 3 times
30 min to home
Sit overnight
Won't start
This morning I checked that the battery terminals and battery clamps all had the exact same voltage. There are occasionally amps between the batteries (.37 to .08) measured on each end of the cable going over the radiator.
So, if there is no drain and the block heater doesn't work, but it starts fine if it hasn't been driven/sitting, what is next to check?
I have a 99 F250 super duty 4x. It's all stock except for some speakers I replaced when I got it. The others were blown from my uncle. I don't have any amp or anything like that and the truck has ran fine for 3 years so I don't think the alternator has failed because of that. I'm thinking just age and 138k miles.
I was wondering what generation of alternator might be on there and how to tell the difference between the generations.
I have 12.5V with the truck off, about 14V with it on idle. As soon as I get it around 3000 RPM the battery light comes on and the voltage goes to 12.5V. Where can I get a rebuild kit for the alternator. I don't see anything at the major parts shops (napa, oreilly, autozone). Could this be the voltage regulator(that I did see at the stores)? I think its mounted to the back of the alternator. Is there any way to test the alternator further?
I'm a little confused as why it would be only above 3000 rpm. Are there two separate circuits for it? Like a low rpm one and then a different one above 3000 rpm?
I have a 97 F250 HD. Wiring the rear tail lights. When we bought it the had cut off the wires going to both sides of the rear lighting assemblys and I was wondering what wire went to what i have the left turn signal working just can't seem to get the brake/back up light to work on that side and i can't figure out how to get the right side going either.
View 8 RepliesI just bought a hard to start 1990 F250. Per the board, just replaced all 8 glow plugs with Motorcraft. Still wouldn't start (it turns over but will only start if you use either). I attempted to install a new BWD brand (Borg Warner I believe) glow plug connector relay today...I removed the old no problem, but am unsure what wires to plug where....the only connection that I'm sure about is the blue wire that works the WTS feature...it plugs in easily but I don't know if there are other connections that need to be made or not? All the wires run from the posts and into the bottom of the unit.
View 2 RepliesI have a 02 f350 can not get power to a/c compressor have power at high pressure And low pressure can run a hot wire and ground to compressor and it works.
View 1 RepliesJust bought an 04 Super duty with the factory plug 7pin and 4 pin plug. Checked the fuses and finally tracked down the 2 relays under the hood but can't seem to find anything wrong. Everything on the trailer works except for the running lights. Is there another fuse or something I have missed? Trailer works fine on my buddies Duramax and worked fine on my old 97.
View 14 RepliesNeed a wire diagram. I have a connector in the cab that has red,blue,lt green,white wires. It's causing my brake lights not to work. I need a wire diagram that shows were they go. I can't find these wires in my Haynes manual.
View 3 Replies