Ford Wiring/Electrical :: 1996 E350 - Dash Losing Power During Cranking No Start
Nov 28, 2013
I have a 1996 E350 7.3 pstd and it hasn't started since April... Van ran great but had bad bearings in the steering column. I changed out the bearings around the steering stem and it hasn't started since but turns over just fine. The main symptom is the dash loses power when key is rotating from the last run position to the spring back crank position. Basically halfway between run and start the the dash drops power. You can see the problem very well in this video I'm attaching.
I filmed this moths ago so the dash is in disarray and I'm using a screw driver to activate the ignition switch. The screw driver bypasses the key cylinder which I thought was the problem but it's not. Parts I've replaced include new glow plug relay, new ignition switch, alternator rebuilt, 2 brand new batteries, new cps sensor, and also a new pcm. All fuses and relays have been checked and most have been tested, pcm gets power in run position as well. Gotta get this thing figured out it's been sitting for 6 months
Watch the video : [URL] ....
View 5 Replies
Advertisement
I bought a 1952 F1 that is mounted on a 1978 E350 chassis.( 351W )
It has all the 78 wiring installed. When cranking engine, it will not start, unless you release key to run position. You have to get engine turning over, and then quickly release key to start. Checked back of switch, not losing voltage at ignition post while cranking...
View 5 Replies
I have a trans temp gauge on my 1996 F350, I have it all hooked up and functioning except for the light. I have searched without success looking for where to splice in to get the light on and have it dimmable. I have a wire routed from the gauge to the center of the dash behind the stereo. What wire I can splice into?
View 2 Replies
Where can I find/buy a wiring schematic for a 2012 Ford E350 with the 5.4 L V8?
View 1 Replies
I am currently converting a 1999 E350 7.3 diesel bus into a camper to live in. The bus has already had a lot of weird custom work. Done by someone else and a lot of the interior torn out and extra insulation put in. There is an exposed electrical panel behind the drivers seat. It was a cheap buy, previously fleet maintained with only 120k.
I was hooking up a battery for accessories to a terminal labeled "Battery" that does run indeed directly to the + terminal of the battery in the engine compartment.
Unfortunately I mistakenly connected the accessory battery to a terminal labeled "ignition" that runs to behind the dash. When I tried starting the vehicle off the auxiliary battery for a test everything went out for 2 seconds, I heard a click from the engine compartment, and everything than came back on. This is when I realized my mistake.
It used to be the speedo only didn't work (which I assumed was the step motor), now after this mistake all the gauges, the odometer and the buzzers don't work. Lights like the battery and airbag warning indicator still function.
Checked fuse 2 (15 amp) for the instrument cluster and it is intact. Actually checked every fuse in the vehicle in both fuse panels and all are intact. The radio works though and the vehicle is not equipped with power windows.
Going to go get a radio removal tool to take apart the dash and get back there. What this could be? Did I fry a relay? Did I fry the cluster circuit board.
View 6 Replies
Car started losing electrical power on the way home from work last week. Dim lights, blower stopped, wipers stop, almost stalled out when getting off the interstate. Barely made it home. 30 minutes later went out to troubleshoot and it started right up. Ran for about 2 minutes and stalled out from lack of electricity. Put voltmeter to alternator and it seemed to only be putting out 8.5v. Took to store to have tested. Replaced alternator and it didn't work. Reman alternator still seemed to only be putting out 8.5v or so.
Checked fuses and cleaned battery terminal and verified good block ground and good body ground. Still having problem. 1996 Taurus. What next? Battery is exactly 2 yrs old and was putting out 11.6 when the problem first started last week. Due to cold and this existing issue, battery is only at 6.5v right now. Can jump the car, but then after removing jumper cables car dies in 30 seconds. Should I have the battery tested? What else could/should I be looking at?
View 8 Replies
I have a 2007 e350. I installed a battery isolator and I believe I need to run a wire from the ignition circuit to the exciter post on the isolator. I found the Power Distribution Panel under the hood (drivers side) which has a fuse in slot #7 (60 amp Maxi Fuse) listed as Ignition Switch/Accessory Delay. What is the best way to tap into this?
Also, I have 8 gauge wire which I ran from the isolator to the batteries. I am second guessing this now and wondering if I should go with thicker wire?
View 5 Replies
Was driving one day, and when I came to a stop sign, the car just died.. I couldn't start it up, so I pushed it to the side of the road.. I tried to turn the key again, and it fired right up... No issues for about a week, but then I came outside one morning, and the car was completely dead. No interior lights, dash wouldn't light up, nothing. (no cranking noise when you try to turn the key) I assumed it was because the battery was old, and the car had just been sitting there for about a week without being started up. I was about to give it a jump, but when I opened the door, the lights came on. I put the key in the ignition, the dash lit up, and the car fired right up.. No issues for about a week, until again, came outside, car was completely dead..
I used my other car to run up to the store, and when I came back, decided I would try to start up the DeVille again. Randomly, upon opening the door, the cabin lights lit up, and sure enough, car fired right up... no one had touched the car while I was gone.. I drove the car up to a shop near my house, where they tested the battery, which tested good. Terminals are all clean, and he made note that the ground connection to the car was also firm and clean. He offered to run a diagnostic the following Tuesday for $125. I returned home, drove the car once more over the weekend, but when I went to start the car Monday, it was again, completely dead. It's been over a week now, and I haven't been fortunate enough to get it to start. I again tried this morning in hopes that I would get lucky, but it's still completely dead.
View 19 Replies
I must be missing something here. Where is the flasher for the turn signals? It isn't the two relays behind the radio is it?
View 2 Replies
My 97 E350/460ci occasionally sets trouble code 4011. It clears every time I check it with my code reader. Something about insufficient secondary air injection. The dealer ship couldn't duplicate/diagnose the problem. Maybe something with the air injection solenoids.
Otherwise, it runs fine. I did notice on the passenger side of the engine compartment a large black metal filter looking thingie with about a 3/4" outlet that doesn't have any hose on it or seem to go anywhere else. Once in a while when you start it i hear a sort of soft popping noise for a few seconds that I would associate with the air pump.
Also can't get the ABS light to go away. It's out when you start it but as soon as you get going it comes on. I flushed the fluid and replaced the rear sensor to no avail. Also tried to flush out the front tone wheels and sensors.
View 3 Replies
I have a 1988 Bronco II 2.9 5 speed 4x4. Ive had it for about 2 years and the other day I put on a new cap and rotor and plug wires. I also cleaned the IAC. After that it ran fine for about a day and then I made a 2 hr trip and cut it off at a store. When i tried to recrank it, it just turned over and over and over for about 10 minutes and then it finally just cranked and ran like nothing was wrong. Its done the same thing twice since then (past 3 days) .
Yesterday when it did it, I pulled the coil wire and put a "spark tester" plug in the wire and tried cranking it. It only sparks right at the end when u quit cranking, itll spark 1 maybe 2 times. It'll crank if you just do a few short bursts of turning the ignition key to on. What else to check, or what the problem probably is? At first i was thinking it was the coil or module, but its only when cranking so maybe an ignition key problem or relay between there?
View 14 Replies
I have a 1983 E350 RV with a 460 engine. It would appear that many "Mechanics" have altered the wiring in different ways. That being said I think the charging and starting electrics are fairly untouched. My issue is that once it has been running for a while the interior lights start to fluctuate so does the radio display. The AC fan speeds up and slows down and I feel like there is not enough gas being pumped up too due to some coughing and sputtering. When I press the brakes the radio stops playing and if I have the AC on it gets worse. Today I changed the voltage regulator and it made no difference. This vehicle has two batteries, one for starting the van like normal and one to run the coach part. The alternator charges both. I think it must be a bad ground somewhere but not sure where to start.
View 2 Replies
Tried to start my truck after sitting for 2 days in sub zero weather. wouldn't crank. pulled the batteries and charged them over night. Tried to start it the next day-wouldn't crank but the starter relay clicked. Was going to pull the starter and check it but decided to replace the relay first. replaced it and tried to start but now have no power to the cab-nothing comes on. I've checked the batteries with a load tester and they are ok. I've checked the fuses and they seem to be ok. when I tried to start it and the relay clicked there was a loud buzzing noise that seemed to be coming from under the dash. it has done this before but this time was louder than usual. I live out in the sticks so taking it somewhere is a last resort. It is a 1999 7.3 with 290000 miles.
View 14 Replies
My 1999 Ford Ranger XLT, 6 cylinder, auto trans, with 134K miles has an electric problem. When I turn the key to the 'on' position, all dash lights show normal, headlights work, radio plays, etc. But when I turn the key to the 'start' position, all electric power is lost. The power remains lost until I disconnect and reconnect the battery ground wire. After reconnecting, I again have power until the key is turned to the 'start' position. I was able to jump start the truck, so I assumed I needed a new battery. I bought one a week ago, and was back to normal until today. The truck started, I drove 4 miles to the grocery store, and then I found myself back to square 1 (i.e., the no-start situation).
View 3 Replies
I have been trying to resolve the last of my codes on my MAF conversion on a 460. I am using an EEC-V box and had two codes I couldn't get rid of. I solved one yesterday, P0443 a evap purge code, by running the circuit directly from the EEC to the VMV.
The current issue is a code P1351, which is the IDM circuit. When I put everything together originally, I assumed that all the later systems used the black CCD module, Motorcraft DY-533. Adam Maurer asked that I check this to be sure. When I went to the Motorcraft website, I found that all 460 remote modules are listed as a DY-1075, gray push start.
The wiring diagram (from the 1995 and 1996 EVTMs) shows a yellow with black stripe wire (circuit 382) from pin 3 of the ICM to either pin #4 (EEC-IV) or pin #48 (EEC-V). Older systems show to start (circuit 32, red with light blue) to pin #3 of the ICM and a suppression resistor from circuit 11 (coil -) to pin #4 of the EEC-IV. which ICM a 1996 EEC-V 460 should have?
View 1 Replies
My beloved 1995 Dodge Ram Van has intermittent dash panel electrical issues. The gas gauge an speedometer are intermittent, coupled with lights and radio on off too. It It all started when I had the transition services years ago. It has less than 100k mileage.
View 1 Replies
Dang, won't start again. My auction truck needed batteries, so I put mine in it and bought new ones for my work truck. Couple of days later, didn't start. Checked SG and I wasn't getting enough RPM. Jumped it and it fired right up. Replaced one of the new batteries and it's started fine the last few times, until just now, in the parking lot of the tire store.
The RPMs were weak - they'd go over 160 but then fall back to the 140s. I walked home and got my auction truck, jumped it, and it still doesn't start. Just spins. RPMs still fall back to the 140s after a few seconds of cranking, but they got as high as 220 so I don't think that is the problem. Fuel pump runs, the upper bowl is full, no bubbles. Oil pressure registers on the dash after a few seconds of cranking.
The last time, I wiggled some fuses and it started. Not this time. FICM at 48, ICP around 700 while cranking. Volts and IPV are good. FPW is 0, but I think that's right, until it cranks. Same with Sync - at 0 while cranking - does it ever go to 1 without starting?
It acts like it has in the past - cranking just fine but no start. And in the past, when it finally starts, it acts like nothing was ever wrong. I checked my IPR screen about a month ago after replacing it about 6 months ago when it didn't start. What am I missing? I'll go read some threads for clues.
View 14 Replies
2000 XLT F150 4.6 - New starter & solenoid(s), battery cable & fuse links good.
When i turn the key, I hear one single click and the power cuts out entirely. I can't attempt a second start or turn on the lights or have any power going through the truck until I disconnect the battery for about 10 seconds then reconnect. Electrical becomes live again, then when the ignition is turned the electrical cuts out again. I do hear a single cluck at the starter (probably attempting to engage when it cuts out) and a clunk right at the inside fuse box (drivers side).
View 6 Replies
i have a 96 ranger and want to put cruise control in it. is the wiring there and what other parts do i need to get without going aftermarket.
View 1 Replies
1965 F100 300cid electrical drain...
I am attaching a link to my thread in the 1960's truck forum : [URL] .....
With my limited skill level, I have given up! It could very likely be something I am doing wrong with the diagnoses/troubleshooting.
Basically, When I turn the key to start the truck, I get a clicking solenoid at best and what appears to be a total loss of power. Not even the dome light will come on. The starter is new as is the solenoid.
View 2 Replies
Have and intermittent condition with my 1996 F-150 4.9. AC runs and then cuts out (compressor not turning). I lose 12v to both side of high side switch. I tried to troubleshoot using a schematic in Haynes Foprd Pickups and Bronco for 92 and later F-Series/Bronco, but the color code for the wiring doesn't match up.
On my truck, there is 2 wires from the low side pressure switch which mates to a socket with only 1 wire. I have 12 volts at switch terminal on dash control, and it seems that I have an broken wire behind the dash, as I can get it to operate again when I move the harness around. Where can I get a schematic of this part of the circuit?
View 5 Replies
