Ford Wiring/Electrical :: 1987 F150 - Wiring Diagram With Carburetor?
Oct 7, 2002
Looking for a wiring diagram for a F-150 XLT LARIAT 5.8L 4BBL, all the books I have looked at show the wiring for this year with fuel injection and this truck came with a 351W with a Holley 600 4BBL, I have a few wire's in the engine compartment that melted away all the insulation, they are located close to where the harness passes the firewall before the ignition module. Is this a common problem on old models ?. Need a clear copy of the correct diagram for a f-150 1987 with carburetor, how I can get a copy so I can fix this problem before it gets worse.
View 3 Replies
Advertisement
Any COMPLETE headlight switch wiring diagram? Everything I find online only shows 2-3 wires in each sub connector, nothing with all wires and colors, and what they do. and of course the factory service manuals no longer work on my new computer. the switch and associated wires went up in smoke 2 hours ago, and this truck is my only means of transportation rite now. what i need is headlight wiring with colors so i can temporary hook up a toggle switch to have lights until the new switch and connectors come in next week. I went to pull the switch and connectors out of the parts truck, but of course that does not have fog lights so it uses different switch and connections.
View 14 Replies
Looking for a source for a wiring diagram for the 2003/4 f350 instrument cluster, specifically the wiring/connectors to the gauges? A link to a PDF file would be nice. I would like to try and disconnect the PCM control to the transmission temperature and engine temperature and drive the gauges from my own sensors to bypass the non-linear behavior that ford decided was in our best interest. I am NOT interested in installing any more gauges, just want to control the ones already present with my own signals. It is possible that these gauges are all addressable devices on a common bus, instead of individual controls.
View 8 Replies
I am curious if it is possible to make a stand alone controller for the electric shift transfer case in a 2000 F-350?
The reason I ask is, this is swapped into a 4x4 conversion in a van and I would like the transfer case to work like the factory, but I don't want to swap over the whole GEM module. I have the high to low and low to high shift relays and wiring, the selector switch from the dash.
I know that powering up the relays will shift the transfer case, but the GEM module tells when the relays need to shut off, and that is where I am not sure what to do. I am assuming that the other plug on the shift motor (6 pin plug) is the sensor that tells the GEM module where the shift is at.
What needs to be done (with a bank of relays).....
View 10 Replies
Need a wire diagram. I have a connector in the cab that has red,blue,lt green,white wires. It's causing my brake lights not to work. I need a wire diagram that shows were they go. I can't find these wires in my Haynes manual.
View 3 Replies
I am trying to add courtesy lights to the existing reflectors in the front doors of my supercab. I can't find a wiring diagram that shows where to connect the light sockets. 1999 F250 SD...
View 2 Replies
I'm trying to find the wiring diagram for the power windows in a 96 f150. I've got a set of these that i need to fab a harnes for to install in my 82.
View 12 Replies
Where can I find/buy a wiring schematic for a 2012 Ford E350 with the 5.4 L V8?
View 1 Replies
Only numbers 1,2,5 match the diagram below. my 6,7,8 are BK/W, PK/B, BR/PK. My Sony CD player came with bare wires. So I could cut off the truck oem plug. How hard is it to find a plug that goes from my OEM plug to my Sony CD player?
View 10 Replies
So I bought my 1987 F150 XLT 4X4 (4spd) about two weeks ago and haven't had any issues with it so far... until now. As soon as I got it I did a full tune up. Changed plugs, cap, rotor, fuel filter, new battery, sea foamed it, fuel filter, ran a bottle of fuel stabilizer through it, new pvc valve, cleaned the throttle body, oil change, etc., ( all the usual things).
Was running fine up until two days ago when I was driving down the highway doing about 90km/hr in 4th when the truck suddenly lost power, sputtered and died. Tried to start it again and it will turn over but not start. So I get a nice expensive tow home and start to diagnose the problem. It is not a fuel issue. I can hear the pumps coming on, and fuel is coming out of the fuel filter so I cross that off the list.
Next I check for spark. No spark at all. So I run some tests. Battery is putting out 12V, about 10 when cranking. The solenoid is getting power and putting out power. No visible damage to any of the wiring, and all the grounds look good.
Next I just went ahead and swapped out the coil thinking that could be the issue. Didn't work. So I preform some more tests on the old and new coils. Both are grounded and having voltage pass through them. Next I take the TFI module off the distributor and check for resistance. Everything still checks out fine. Now I am thinking that the only thing left could be the PIP in the distributor. So instead of taking the dist apart and screwing around I go ahead a get a brand new dist and throw it in.
Now I am stoked and thinking that I finally fixed my truck and go to start it up and.... no spark. It still turns over but no start. I am trying to provide every bit of detail that I can. When I say I tested all the components I mean I REALLY tested them. I did both tests from the Haynes manual and from various sources off this site.
I am almost at the point of getting it towed to the shop, which I really do not want to do. A day before this happened I degreased the engine and VERY carefully sprayed it off with water. In the process I am thinking I may have damaged something?
View 1 Replies
I posted earlier about the tranny in my 01 Ex v10 having a transmission problem. The show looked at it and found the O2 sensor had shorted out and in some way sending the truck in to limp home causing the tranny fuse to blow????
Any way they fixed it or so they said and I drove it for a few hours and it did fine. The next morning I drove it and it blew the fuse. (under hood box I belive #19) I took it back to the shop and they beat and banged on it....got it wet etc. and can not get it to do it again. I know whe have an electrical issue but what all runs off of the fuse that controlls the tranny?
Is there any online wiring diagrams of excursions or superduty drive trains? Where all to look for the problem?
View 4 Replies
1987 F-250 4x4, 460cid... My engine compartment harness smoked. Do the 1987 models have wiring problems and I need any wiring diagrams that are out there.
View 6 Replies
My F250 is acting like the battery is almost dead but its not. I've checked all the grounds I can think of, used jumper cables and clamped right to the body and still nothing. I put my battery charger in place of the battery and my charger almost caught fire! Where are all the ground points at and points to check? It was doing fine then this. I only found 3 ground points on the block and I bypassed all of them and nothing. There are 2 large on the front of the block, I was able to get one loose and "clean" it but not the other. The block to firewall is currently off so I can clean it in the morning.
But it didn't do anything. I can clamp anywhere are get the same results. There are a few threads about this truck and trying to get it back into shape. When it worked, when I turned the key on, gauges worked, RABS, Engine, and Battery light came on, GPs kicked on, etc... now, I get a very faint Batt light, Erie dinging, and not even the stereo now. This truck has been an electrical nightmare since day one. Spent 4 days on just under hood electronics alone. Haven't even moved towards the back. Also, Instead of using a 2/0 AWG wire to the starter, Can I use two 1/0 AWG wires to it instead since they used two separate grounds? It also still has a 2G alt.
View 5 Replies
Here's the breakdown. I have a '95 Ford F150 that I bought the previous year and it has been nothing but a problem. The most recent problem is the attempt to turn on the headlights. I will pull the plunger to turn on the headlights but I will only get the parking lights and when attempting to turn on the high beams I still get nothing. The only way that I get any sort of lighting is if I pull on the turning stick (almost like doing a manual override on a tripped wall plugin). Now here's the kicker. I still have parking lights, brake, tail, cab, and dash lights. Winter in quickly approaching and the nights are already getting dark, pretty soon the days will be just as dark.
View 3 Replies
I got my first truck today and it's a 1988 Ford F-150 and it runs great! The only issue is that the speedometer doesn't work and I won't be able to register it until it does. I was wondering what I can try out to maybe fix the issue and if not, how I would replace it. Every other gauge works, it's just the speedometer that isn't. The needle doesn't move at all it just sits at a 0 all the time.
View 8 Replies
I have been trying everything to get my speedo working on my Ford. It didn't work for 3 months after I got it then I decided to put some gear oil on the cable. This made it work for about 200 miles then it would only work with the clutch in and then not at all. I've replaced the speed sensor(not one on rear end the thing the cable goes into), and the gear that goes on the end of it. If I hook a drill up to the cable the tach moves. Could the cable be stretched or just needs some speedo cable lube?
View 5 Replies
I have a 1999 Ford F150 6 cyl. 4.2, 2 WD with 160,000 miles. Replaced the battery May 2010.
Today battery light came on. Battery gauge did not look like it was discharging. Had battery checked they said it was a little low but OK. Then they continued test and tried to check alternator, test stopped and they said something wrong with alternator most likely.
I took alternator out and had it bench tested. They said it was OK, putting out 98 amp on 95 amp alternator. They said check wires, grounds, harness, connections. Checked connections and wires as much as possible, reinstalled alternator, light still on.
Have not checked fuses yet. Was told to start vehicle, disconnect positive battery cable and if engine continued to run alternator was good, if cut off alternator was bad and to replace. Should I try this and is it true?
What is the part on the fire wall that is between the alternator and the battery that the wire connection runs through? Can it be bench tested/checked?
View 5 Replies
My center brake light went out a month ago. Thought it was the bulb so replaced that, still didn't work. Checked the fuse and its not broken so my guess was electrical?
Hasn't come on once that I know of but I was randomly walking behind my truck and the light was on. Truck was off lights were off and key wasn't in the ignition.
Went and turned my truck on and turned the lights on and the cbl stayed on. When I switched my lights off it went out and stayed out.
Now I'm definitely thinking wiring but not sure where to start fixing?
Oh and it's a 1990 F150 XLT
View 2 Replies
Just bought a used, 03 F-150 SuperCrew Lariat. Having some minor electrical issues. While cleaning truck, I discovered a red wire coming into engine area on passenger side of vehicle. Wire has a built in 40amp fuse but isn't connected to anything. What this is for/ should be connected to???
View 1 Replies
After replacing my battery cables (Pos and Ground),My Truck stalls every time I turn on the headlights. The truck stays running with the parking lights on or if no lights on at all. Could I have mixed up the 2 positive accessory wires?
View 13 Replies
My '84 F150 4X4 inline 6 Died last night while driving. just conked out and died right there on the spot. no sputter... no gasping... just instant death...
after some investigation i found i wasn't getting spark anywhere. not at the plugs, not at coil. I have replaced the ignition module to no avail. still no spark I am going to swap in a the coil tonight. sure do hope this works.
View 9 Replies
