Ford Wiring/Electrical :: 1985 F150 - Hot Wire The Truck To Start?
Feb 11, 2006
My 85 f150 5L is parked to far in into my alley.. the last time i saw my keys i moved it up to water the plants that it was tucked almost on top of.
ive been looking for the keys for 2 months.. the truck isnt being driven at all but i think my neighbors are getting mad at it being out so far.
I can get in the engine bay, and i have jumped the starter on our big trucks at work before.. but what wires do i have to join to put the ignition into the run position?
View 9 Replies
Advertisement
Where is the cruise control amplifier located on an 85 F-150? The Chilton manual just says "behind the instrument panel". No pic or further description. Just looking up from the bottom of the dash I see a "black box" with 2 wires going into the top of it located just between the steering column and the wiper switch.
Is this it?
View 2 Replies
I have a 1998 Ford F-150. It has an issue with starting sometimes. The truck won't start with a fully charged battery but when I hook it up to a charger, the truck starts normally. It was going to get the wheels aligned today and when the mechanic went to drive it off the ramp, it wouldn't start. I told him to put a charger on the battery and it started right up. Without the charger it just cranked over and wouldn't start. It doesn't do this every time I go to start it only occasionally. The mechanic had no idea what the problem was and has never heard of this kind of situation. I'm assuming it is an electrical problem but I'm not an expert with engines. The battery was fully charged at the shop and the battery is a year old.
View 4 Replies
Just bought a used, 03 F-150 SuperCrew Lariat. Having some minor electrical issues. While cleaning truck, I discovered a red wire coming into engine area on passenger side of vehicle. Wire has a built in 40amp fuse but isn't connected to anything. What this is for/ should be connected to???
View 1 Replies
I've searched all over and can't seem to find the answer. When I pull the tail light out of my 12 F150 there is a blue/wht wire and a black wire going to the back up light. I assume the blue wire is the positive and black is the ground. Is that correct?
View 8 Replies
The red wire coming from my fire wall is not connected to anything and I need to find what it is supposed to connect too it come out of my firewall near my steering column ... This is and 95 f150 with a 302 engine ...
View 1 Replies
My 77 F150 Ranger with a 400 in it didn't wanna start up at all. It wouldn't even crank or click like if the battery was dead. Then I tried again this morning and it cranked once then melted a red wired with I think a black or gray tracer, on the ignition. (I put a new solenoid on a couple months back and the positive also melted a bit by the solenoid but didn't pay any attention to it.) I'm just wondering what could be wrong with it to make it do that and how to fix it. Also when I went to put gas in it (it's on a slight hill making it lean to the driver side) it was empty but no fuel would go down the filler neck, then it started to gurgle and spit it out some. I was told it was vapor lock but I thought vapor lock happens when it's hot.
View 3 Replies
I have an 08 F150 5.4L with about 68k miles. When the temperature is 40 degrees or colder it will not crank. I had the same issue with my 2005. I can turn the key and nothing, lights, radio and everything work. The dash display has dashes all the across for the miles, temp and compass. I have found out that it doesn't matter if I leave the key forward in the run position or try to crank, it won't do anything.
Battery is good and no problems with the truck. After the key is in and I give it anywhere from 15 to 60 seconds you can hear an electrical click real faintly and see the red security light come on and then the computer display comes on and then I can start with no problem? What could this be? My dealership has no clues and I can get it to act up because after I get it there it starts with no issue. The remotes work fine and this issue was why I got rid of my '05.
View 2 Replies
2000 XLT F150 4.6 - New starter & solenoid(s), battery cable & fuse links good.
When i turn the key, I hear one single click and the power cuts out entirely. I can't attempt a second start or turn on the lights or have any power going through the truck until I disconnect the battery for about 10 seconds then reconnect. Electrical becomes live again, then when the ignition is turned the electrical cuts out again. I do hear a single cluck at the starter (probably attempting to engage when it cuts out) and a clunk right at the inside fuse box (drivers side).
View 6 Replies
I have a need for a 12-volt signal to indicate the engine is in start or run mode. I would like to pull this from the engine compartment but I'm not sure what would be the best or easiest way to do this. The 12-volt signal is not used to power anything so it will draw very little current. I have a 94 F150.
View 8 Replies
My neighbor's kids truck battery drains from full charge to "no start" in 1-2 days. 1999 Ford F-150 w/ 4.6L engine. He has already.....
1) Replaced the Battery.
2) Replaced the GEM module.
3) Replaced the Turn Signal Relay.
He did all this before I looked at it....
I checked the following....
1) Truck off, doors closed, hood open... Amp meter shows 3.6 amp draw. When 1st hooked up, shows 4.2 amps... after a while drops to 3.6.
2) To isolate the draw, we pulled fuses while checking current draw at battery.
a) Under Dash fuse Panel. (Yes, with door closed) We remove fuse #15 "stop lamp switch, speed control, brake shift interlock, ABS, PCM,GEM, RABS test connector". (Really... couldn't be more stuff?)
b)Under the hood is another fuse box (drivers side). We remove Fuse #103. "Junction Block Battery Feed".
3) Found that if we remove the #15 fuse under the dash with the door opens, all interior lights flash on/off at about 1 second intervals... weird.
4) Again, another weird one... with the fuse #15 removed and door closed, the "ABS" indicator and some other indicators and dash lights are staying partially lit... not fully lit.
5) The only "aftermarket" stuff i can see is a dealer installed trailer brake system. Wiring looks professional and disconnecting it does not remove the amperage drain.
I'm hoping that one of you wizards will give me the "slam dunk"... if this happens, it must be that. Can I be so lucky? And, yes. I have my own '06 F-150 that i absolutely love. 6-cyl., manual trans, stripped down without even power door locks... my kinda technology.
View 8 Replies
I am trying to hook up my power door locks to my command start. I am having trouble getting it to work. Ive tried a number of relay diagrams from the12volt.com. I've tried actuators/reverse polarity and it blows both my factory door lock fuse and the fuse I have supplied to the relays. Ive also tried 5 wire alternating 12 volt positive door locks, and 3 wire positive door lock combinations. Both of these combinations the relays click back and forth fine with the actuators unhooked, when I connect the actuators the doors unlock with the factory switch but when I unlock with my remote it blows the fuse. How to properly connect the actuators?
View 3 Replies
I have an 85 bronco ii 2.8l, carb, with around 109K on it , ran pretty good, some stubles here and there but found out how to read codes and went from there.... Retreived codes 23, 31 and 84. Checked TPS, had voltage to sig return pin but was low, pulled the carb, bought a rebuild kit while i was at it and redid most of the gaskets but did not take the inner parts of the carb out, put on a new TPS, installed the carb, unhooked battery for about half an hour and noticed it idled very high. Once you were moving the rpm's would drop but at idle would climb again. I ran the codes again and got 31, 63 and 84. checked volts from black to vref i have 4.9 and from black to sigrtn i have 0. i have traced all 3 wires through the bundle and did not see any breaks i know that the green wire goes to the ECM? but i do not know what to check from this point.
View 2 Replies
Looking for a wiring diagram for a F-150 XLT LARIAT 5.8L 4BBL, all the books I have looked at show the wiring for this year with fuel injection and this truck came with a 351W with a Holley 600 4BBL, I have a few wire's in the engine compartment that melted away all the insulation, they are located close to where the harness passes the firewall before the ignition module. Is this a common problem on old models ?. Need a clear copy of the correct diagram for a f-150 1987 with carburetor, how I can get a copy so I can fix this problem before it gets worse.
View 3 Replies
I have a 70 Ford f250 with a messed up wiring harness. Truck will run only in start position. which wires are wrong.
View 7 Replies
85 ford ranger 2.3 efi .. My brake lights still aren't coming on. According to the Haynes manual, the wire that runs from the stop light fuse goes from there to the hazard flasher and then to the brake light switch. Since I have checked everything else, is it possible that the hazards are causing a break in the connection?
View 4 Replies
Only numbers 1,2,5 match the diagram below. my 6,7,8 are BK/W, PK/B, BR/PK. My Sony CD player came with bare wires. So I could cut off the truck oem plug. How hard is it to find a plug that goes from my OEM plug to my Sony CD player?
View 10 Replies
2001 F-350 diesel. Out of nowhere, I start the truck and there's no turn signals. Fuse is blown so I replace it. It immediately blows. Tail lights work. No turn signal, brake lights, or hazards. I haven't hooked up a trailer or done anything abnormal recently. Only the #1 fuse (20Amp) is blown. Pulled bulbs and they work fine. Inspected wiring under and near lights. NOTHING! Any way to localize a short?
View 2 Replies
85 f150. My driver side brake light and turn signal in the back quit working. The tail light works tho which is a different filament. The bulb is good and I changed the flasher relay...the circle thing in the fuse panel. Everything else works just fine. looking for a starting point.
View 7 Replies
I'm planning the install of a 1996 351w into my '77 F-100. I'm using the '96 accessory serpentine drive (FS-10 A/C compressor, '96 alternator, etc.). It needs to mate up to the '77 wiring. I'm going to use stock '96 underhood A/C components (accumulator, hoses, condenser).
As best as I can tell, the '96 system uses the ECU to manage the A/C system, but I've converted the '96 motor to a carb.
Looking at both the '77 and '96 systems I think the easiest underhood wiring solution would be to use the '77 compressor ON wire as a relay trigger, and use the '96 High Pressure Cut Off (HCPO) on the compressor manifold, and compressor cycling switch attached to the accumulator to interrupt the relay output to the compressor.
I can get the switches and pigtails, and I can look up their pressure trigger points, but I don't know the voltage the '96 switches operate at (12v or some reduced voltage?) or how to simulate their trigger conditions to see how they work. I guess that at ambient pressure the HPCO should be normally on and the cycling switch should be normally off. So I could just wire them into the relay ground or trigger connection. But of course they aren't simple two wire switches. (Edit: Looking at it online, the cycling switch appears to be two wire, the HCPO is 4 wire).
How to wire them, should I use them to interrupt the relay ground or trigger connection?
View 7 Replies
On a 2008 E250, Where is the dome light wire and what color is it? To use with an omega security system.
View 4 Replies
