Ford Wiring/Electrical :: 1983 F250 - No Spark At All
Mar 20, 2016
I have a friend of mine that has a 1983 and he had me change the water pump in it because it started leaking and it has been sitting for 7 Months now. I changed that but I can't get this bugger to start. I used to be a mechanic in a past life so I know what I'm doing most of the time so let me explain what has transpired here.
I attached my remote starter, turned on the key and cranked over the engine after shooting a little bit of starting fluid in the carb and she cranks over but won't start. I then pulled the #1 spark plug out and then did the same thing to check for spark and nada. I put my light tester on the coil and there was power. I have run into this kind of problem years ago with other vehicles so I thought I would just go ahead and replace the Coil and also the Control Module. After replacing these parts, still no spark. Since the distributor is there only to distribute the spark (meaning no electrical connections to it) I'm assuming that the Pick Up part that is down by the Crank shaft might be bad.
How to test either the Control Module or the pick up. I'm trying to diagnose this problem without needing to remove the module and taking them to the parts house for testing. (long drive). These wires should have 12 volts when the key is off and these wires should have 12 volts when the key is on.... and so on.
View 3 Replies
Advertisement
I have an 86 f250 i just bought back with no spark. this truck is not original. used to be a diesel. has a 400 out of 81 f250. had this truck running just fine 4 years ago. sold it to a guy running and bought it back 4 yrs later not running.
Checked all the connection to make sure they r clean. Had the ignition modular tested and tested good. I have 12+ volts from the white and red wire. I have a little over 6 volts at the bat side of the coil. I have no spark from the coil. I notice every time I connect and disconnected the bat cable I will get a spark from the coil. i ran a test light from the tack test sight on the coil and tried to start and the light stayed real dim and never flickered.
View 1 Replies
I have a 1983 E350 RV with a 460 engine. It would appear that many "Mechanics" have altered the wiring in different ways. That being said I think the charging and starting electrics are fairly untouched. My issue is that once it has been running for a while the interior lights start to fluctuate so does the radio display. The AC fan speeds up and slows down and I feel like there is not enough gas being pumped up too due to some coughing and sputtering. When I press the brakes the radio stops playing and if I have the AC on it gets worse. Today I changed the voltage regulator and it made no difference. This vehicle has two batteries, one for starting the van like normal and one to run the coach part. The alternator charges both. I think it must be a bad ground somewhere but not sure where to start.
View 2 Replies
I have a 1988 Bronco II 2.9 5 speed 4x4. Ive had it for about 2 years and the other day I put on a new cap and rotor and plug wires. I also cleaned the IAC. After that it ran fine for about a day and then I made a 2 hr trip and cut it off at a store. When i tried to recrank it, it just turned over and over and over for about 10 minutes and then it finally just cranked and ran like nothing was wrong. Its done the same thing twice since then (past 3 days) .
Yesterday when it did it, I pulled the coil wire and put a "spark tester" plug in the wire and tried cranking it. It only sparks right at the end when u quit cranking, itll spark 1 maybe 2 times. It'll crank if you just do a few short bursts of turning the ignition key to on. What else to check, or what the problem probably is? At first i was thinking it was the coil or module, but its only when cranking so maybe an ignition key problem or relay between there?
View 14 Replies
So I've been having problems with my old duraspark 2 ignition box and I replaced that but it didn’t seem to fix the problem. The truck doesn’t start if the voltage is down around 12v, it cranks but no spark. So I put it on the charger a couple hours ago and came inside and was reading old posts on here about testing the ignition system and then just went out to test the negative side of the coil with a test light and low and behold when my assistant went to crank it over the truck started right up like everything was fine. I took off the charger.
So then what I did was I checked the charge at the battery while the truck was running with a dvm and the voltage was 14.33 then I turned on the electric fan and it jumped up to 14.88 and spiked at 15 then held at 14.88. is that normal or is the voltage a little on the high side? If it is high then could it be the voltage regulator or alternator? And could that have been my problem all along instead of the ignition module?
View 14 Replies
I bought a 84 ranger 2.0 that ran when parked sat for six months. Cranks all day long but only sparks when you shut the key off. Replaced the ignition switch (by key) ( someone told me there is another ignition switch under the dash?? is this true?) Tested the icm and it passed all wires seem to be fine. I am just wondering if something in the dizzy could cause this or possibly the starter solenoid?
View 9 Replies
I have a 97 F250 HD. Wiring the rear tail lights. When we bought it the had cut off the wires going to both sides of the rear lighting assemblys and I was wondering what wire went to what i have the left turn signal working just can't seem to get the brake/back up light to work on that side and i can't figure out how to get the right side going either.
View 8 Replies
I am trying to add courtesy lights to the existing reflectors in the front doors of my supercab. I can't find a wiring diagram that shows where to connect the light sockets. 1999 F250 SD...
View 2 Replies
So I bought my 1987 F150 XLT 4X4 (4spd) about two weeks ago and haven't had any issues with it so far... until now. As soon as I got it I did a full tune up. Changed plugs, cap, rotor, fuel filter, new battery, sea foamed it, fuel filter, ran a bottle of fuel stabilizer through it, new pvc valve, cleaned the throttle body, oil change, etc., ( all the usual things).
Was running fine up until two days ago when I was driving down the highway doing about 90km/hr in 4th when the truck suddenly lost power, sputtered and died. Tried to start it again and it will turn over but not start. So I get a nice expensive tow home and start to diagnose the problem. It is not a fuel issue. I can hear the pumps coming on, and fuel is coming out of the fuel filter so I cross that off the list.
Next I check for spark. No spark at all. So I run some tests. Battery is putting out 12V, about 10 when cranking. The solenoid is getting power and putting out power. No visible damage to any of the wiring, and all the grounds look good.
Next I just went ahead and swapped out the coil thinking that could be the issue. Didn't work. So I preform some more tests on the old and new coils. Both are grounded and having voltage pass through them. Next I take the TFI module off the distributor and check for resistance. Everything still checks out fine. Now I am thinking that the only thing left could be the PIP in the distributor. So instead of taking the dist apart and screwing around I go ahead a get a brand new dist and throw it in.
Now I am stoked and thinking that I finally fixed my truck and go to start it up and.... no spark. It still turns over but no start. I am trying to provide every bit of detail that I can. When I say I tested all the components I mean I REALLY tested them. I did both tests from the Haynes manual and from various sources off this site.
I am almost at the point of getting it towed to the shop, which I really do not want to do. A day before this happened I degreased the engine and VERY carefully sprayed it off with water. In the process I am thinking I may have damaged something?
View 1 Replies
1996 Ford F150 5.0 ... New battery, new alternator, new starter, new coil, dis cap good and rotor is good. New plugs and wires. Ignition mod tested good.
Drove a mile from my house and lost power to my engine. Lights and radio work. Just sits there and cranks and cranks. I'm not getting spark from the coil. Don't know a lot about engines.
View 6 Replies
I just bought a hard to start 1990 F250. Per the board, just replaced all 8 glow plugs with Motorcraft. Still wouldn't start (it turns over but will only start if you use either). I attempted to install a new BWD brand (Borg Warner I believe) glow plug connector relay today...I removed the old no problem, but am unsure what wires to plug where....the only connection that I'm sure about is the blue wire that works the WTS feature...it plugs in easily but I don't know if there are other connections that need to be made or not? All the wires run from the posts and into the bottom of the unit.
View 2 Replies
I have a 77 ford truck with a 351 ,the ignition system keeps shorting out, killing spark. If i replace the starter solenoid, it works for a while, then goes out again. I have replaced 4 solenoids this month. What could be shorting the solenoid out? Had the truck for 8 yrs. now, never had a problem with it till now. It has a mallory dist. it was in when i bought it.
View 7 Replies
My '84 F150 4X4 inline 6 Died last night while driving. just conked out and died right there on the spot. no sputter... no gasping... just instant death...
after some investigation i found i wasn't getting spark anywhere. not at the plugs, not at coil. I have replaced the ignition module to no avail. still no spark I am going to swap in a the coil tonight. sure do hope this works.
View 9 Replies
My truck is a 1990 F-150 with the 351. I was replacing the spark plugs last night, got it all wrapped up and everything squared away, and after firing the truck up I noticed a ticking noise. It was not there before I replaced the old plugs, and it is not at all loud. I can hardly hear it with the hood closed. It appears to be coming from the driver's side of the engine. It does not misfire when its idling, and it revs smoothly. However, while driving it is noticeably choppy and feels sluggish.
Any thoughts on what it could be? I used dielectric grease on the boots, but I did not replace the plug wires themselves, or the distributor cap. I am probably going to replace the plug wires today though, because the plugs I took out were not in good condition and its been a bit too long since I replaced them last. Its also worth noting this engine is less than years old. This is a frustrating problem because I've replaced the spark plugs on her before, so I'm not quite sure what I did wrong this time.
View 4 Replies
I recently bought a 92 F250 and love it but the blinkers will not work. I have replaced both flashers and the multifunction switch. (the wipers had issues too that were fixed by the switch...) Now what? Im at a loss..
View 7 Replies
My work truck is an 03 F250 5.3L. My flashers recently stopped working. I turn them on, and they will work anywhere from 5 seconds to a few minutes, then either blink rapidly and shut off, stay solid for a few seconds and shut off, or just shut off. I push the switch off and on again, and the cycle repeats. All my other lights and turn signals work fine with no issues.
This wouldn't be a huge issue, but where I work I need the flashers a lot. The truck has a bar light and siren/pa system wired into it, but not to the lights or anywhere near that. I can't say exactly how it's wired because I didn't install it, but I followed the wires and they don't go under the steering wheel where I would assume the relay and wires for flashers would be.
What sounds like is wrong? I wouldn't think it would be the relay because then I would think that I would be having problems with more than just the flashers. So I'm not sure if there would just be a ground issue or if it's the actual switch that turns on the hazards. Also, there are no lights that are burnt out.
View 6 Replies
I have a 1979 f-250 4x4 with a 351m. The problem I am having is my starter keeps running after the truck starts and also after I shut off the key. I didn't get the battery unhooked in time today and it completely melted the lug off on the solenoid, but the other wires were barley warm. What could be causing this problem? The battery is new, the cables are new and the Sol. was new. Maybe the switch or the starter?
View 8 Replies
I have a 1991 idi diesel f250. My dash lights have entirely gone out and i cannot seem to figure out why, i checked the fueses under the driver dash and under the hood for that matter and nothing is blown.
At the same time, the dome lights, door lights, cab lights, stereo, windows, ever the light in the ash trey etc, work perfectly fine. Could a wire have come loose behind the dash cluster and shorted out everything in the driver area?
I still get the high beam signal, check engine, engine, wait to start, and water in fuel light in the cluster. but no back lighting (when turning the key to the on position)...
View 1 Replies
2002 f250 v10 4x4. Truck will loose all power...
View 10 Replies
I have a '97 F250 diesel and the battery light keeps coming on and off. The volt meter shows a good charge. How do I fix this?
View 4 Replies
I bought a truck recently and I am attempting to get the alternator to charge. A previous owner hacked up the wiring pretty badly. We found that they had connected the voltage regulator to the horn relay for some reason. Anyway, I am trying to get it rewired and have searched existing threads for info and I thought that I had the wiring sorted out, however it is still not charging the battery.
The alternator has been tested and works. The voltage regulator is new. This is how it is currently wired.
Regulator A Terminal --> Battery side of started solenoid --> Alternator Batt Post
Regulator F Terminal --> Alternator Fld Post
Regulator S Terminal --> Alternator Sta Post
Regulator I Terminal --> Empty
Regulator body --> Radiator Support --> Alternator Ground Post --> Neg batt
When running, the battery is showing about 11.8 and slowly dropping as it runs. The truck has an ammeter in the dash, however it looks like it is no longer connected. Does it need to be connected in order for the alternator to charge the battery?
View 4 Replies
