Ford Wiring/Electrical :: 1967 - Installation Of External Electric Fuel Pump?
Nov 25, 2012
I have a fuel pump I want to install I want to hook this thing up on a switch inside the cabin to be used as kind of a security device, but I am hoping I can wire it into the ignition as well.... I want the pump to activate when the ignition is turned on but only if the (hidden from view) switch is in the "on" position. Not sure if all this is possible.
I have heard I ought to utilize a relay to avoid voltage loss at the pump. I have never hooked up a relay to anything before although I have heard of them being used. This system is being installed on a 1967 F250.
View 6 Replies
Advertisement
I am a beginner when it comes to anything involving wiring. I am looking to re-wire all of the wiring coming off of the instrument cluster gauges. Once I have completed all of the wiring on the gauges, I may feel confident to move onto something else. As of rite now, it appears as though my truck is still running on all of the original wiring, and over the past few weeks, I have been having many wiring related issues. I found a schematic that includes the wiring for the gauges that I am going to go off of. I have a couple of questions before I begin.
1.) On the schematic, it shows connectors such as "Connector G" which is moving all of the gauges wires to there locations. Do I need to use a specific Ford connector, or could I purchase a new connector at any hardware store that carries them? As far as I am concerned, connectors do the same thing as all other connectors. (Let you connect and disconnect for easy instrument cluster removal.)
2.) I am not looking to purchase one of those expensive wiring harnesses. I would like to just purchase some wire that I can cut / use myself. What brand / type of wire should I be looking to purchase? I do not care if it is striped / colored as I will use wire tabs to name / label each wire.
Other than that, I feel confident enough to attempt something such as this. Here is the wiring schematic I am going to use.....
View 10 Replies
I have a 1994 Ford Ranger king cab 4x4 with a three inch lift kit on it . My problem is the fuse is blowing that goes to the fuel pump . It started out blowing the fuse now and then when it was raining . Well I thought it mite be the fuel pump going bad but after I put the new pump in the truck it lasted about a week and started blowing fuses again . I put another fuse in and it go a few days and blow it . Last week on a 100 mile tripe I got almost there and it burned a fuse on the highway . I tried to put another fuse in and it would blow it as soon as I tried to start the truck . Burned five fuses right then . So I had it towed to mothers house and put another fuse in and it cranked up . I looked at the wiring that was not wrapped in that plastic cover stuff and have not found anything yet ...
View 14 Replies
I have 2 1986 Ford F250 supercab I switched cabs to put the better cab on my truck power windows wipers heater blower motor all light signals work no fuel gauge power or fuel pump power no power to the inertia switch
View 12 Replies
I am curious if it is possible to make a stand alone controller for the electric shift transfer case in a 2000 F-350?
The reason I ask is, this is swapped into a 4x4 conversion in a van and I would like the transfer case to work like the factory, but I don't want to swap over the whole GEM module. I have the high to low and low to high shift relays and wiring, the selector switch from the dash.
I know that powering up the relays will shift the transfer case, but the GEM module tells when the relays need to shut off, and that is where I am not sure what to do. I am assuming that the other plug on the shift motor (6 pin plug) is the sensor that tells the GEM module where the shift is at.
What needs to be done (with a bank of relays).....
View 10 Replies
My vehicle would not turn over and we could tell it was fuel related. The fiel pump relay has burnt through the motherboard of the fusebox. It is my understanding that this cannot be fixedand another fusebox must be installed. I have been to many junkyards in my are looking for it to avoid the dealer prices..all of the expeditions that we have found locally have already had the fusebox pulled. Any other vehicles that this might be interchangable with? My friend has an 01 expedition..would this work?
View 1 Replies
My 92 F250 5.8 won't start but fuel pump runs all the time the key is on. Some times it runs. But has no power and check engine light is on.. But I cant get it to flash codes, only steady light on.. It did this before then ran good. Now back to no start.. I checked grounds and relays ..
View 2 Replies
OK, this one has me stumped...I have a 93 F150, 302 with the E4OD. I know the transmission needs to be rebuilt (probably a bad pump). When I put it in reverse, the engine will start to bog down and will die unless I put it back into park or neutral.
If the engine does die, the fuel pump does not prime with the key "on" and the engine obviously will not start. If I let the truck sit for about an hour, the fuel pump primes like it should and the engine starts right up. The fuel pump shut-off does not trip and all fuses are good.
View 5 Replies
I have a 1997 F150. I installed a trailer towing kit round 7 pin. I followed the instruction and replaced three different fuses after installation. The passenger side turn signal will not work. I replaced the bulb. The brake light works and the bulb is on when the lights are on it just will not blink. When the turnsignal is on it clicks very quickly.
View 4 Replies
I have a newly remanufactured Holley 1835 carb which has had an electric choke added to it. My '59 F-100 has the original electrical system in place. Where would you recommend running the positive and negative wires from the choke? No instructions came with the carb.
View 8 Replies
Was driving one day, and when I came to a stop sign, the car just died.. I couldn't start it up, so I pushed it to the side of the road.. I tried to turn the key again, and it fired right up... No issues for about a week, but then I came outside one morning, and the car was completely dead. No interior lights, dash wouldn't light up, nothing. (no cranking noise when you try to turn the key) I assumed it was because the battery was old, and the car had just been sitting there for about a week without being started up. I was about to give it a jump, but when I opened the door, the lights came on. I put the key in the ignition, the dash lit up, and the car fired right up.. No issues for about a week, until again, came outside, car was completely dead..
I used my other car to run up to the store, and when I came back, decided I would try to start up the DeVille again. Randomly, upon opening the door, the cabin lights lit up, and sure enough, car fired right up... no one had touched the car while I was gone.. I drove the car up to a shop near my house, where they tested the battery, which tested good. Terminals are all clean, and he made note that the ground connection to the car was also firm and clean. He offered to run a diagnostic the following Tuesday for $125. I returned home, drove the car once more over the weekend, but when I went to start the car Monday, it was again, completely dead. It's been over a week now, and I haven't been fortunate enough to get it to start. I again tried this morning in hopes that I would get lucky, but it's still completely dead.
View 19 Replies
I was wondering if it is possible, due to budget, to perform the electric fuel pump conversion in steps. By that I mean could I remove the mechanical pump and install the electric pump on the frame, but retain the stock filter housing and regulator? I would use high pressure hose and run from the stock pump supply line on top of the engine to the fuel bowl inlet and then use high pressure to run to a three way fitting, and a bit more hose to join the fitting to the stock lines running to the head. later as budget allow I will replace the filter assembly and regulator and then the lines to the heads.
View 2 Replies
I just purchased an 87 f250 w/ a carb'd 460. I purchased it with the mech fuel pump swapped out to an electric. The previous owner states that they gave him the wrong electric pump and I should exchange it for a different one. The reason for him putting it on was to get it running for me to hear it run.
My question: Is this even recommended? I wouldn't mind staying with an electric pump up front. If it is recommended, what would be a suitable pump to replace it with, as in flow/feeding characteristics?
Also, it only feeds from the rear tank, which also has a bad fuel pump. I'd like to get both tanks functioning again. I'd rather not deal with the tank switching valve due to what I've read about them. Has anyone ever hooked up a manual valve and just switched tanks that way? I've searched this site extensively and couldn't find anything. I know I'm not the first to have thought about it.
View 12 Replies
i have had this problem before where the relay for the electric fuel pump would quit intermittently, and had it fixed. but, i suspect this is acting up again. so, i was gonna do it myself. there are 2 relays strapped to the radiator overflow can. is one of them the relay i am seeking?
What started all this, motor was running really rough at idle, but ran ok once moving. So, I replaced the spark plugs, and cleaned the contact areas in/on the cap and bug. motor started right up, and actually sounded good... for about 10 or so seconds, then it died, like the gas was shut off. I do have spark.
How to check/test the fuel pump relay and could pass this info on to me would be good. i do have test light, and DMM.
View 3 Replies
I have a main tank and an Aux tank with a gauge selector switch. I believe I may have a bad fuse as the indicator has stopped working. Where it is on the fuse block??
1978 Ford F-250
View 1 Replies
I swapped a 4.9l into a 1997 F-350 that had a 5.8L originally, my issue is the fuel injectors are not working. I did my homework and got the harness that was with the engine out of a 1995 F-150 and also got the correct PCM to go along with my E4OD tranny that is in the F-350. It has spark and 60 plus PSI fuel pressure in the rail and will run with starting fluid shot in the throttle body. Both vehicles came with OBD I so should be compatible there. I do not have 12v to the injectors and obviously the NOID light shows no pulse either. Could be a ground but not sure where to look or what else could cause this.
View 14 Replies
After my electric water pump was replaced under the recall my mileage went from 45 mpg to about 30 mpg. Part of this might be due to new tires and cold snowy weather (CT !) but I have never seen such a drastic drop in performance (2005 Prius).
View 12 Replies
After changing my radiator support, my fuel and temperature gauges don't work. I looked to see if everything was plugged in and I don't see anything unplugged. I do know the older trucks used the V-R regulators, but I don't know about this model.
View 2 Replies
I have an 01' f150 that everything is going out on. I've replaced the GEM module thinking that's what it was to no avail. First thing to go was all four windows which have currently been stuck halfway down for 2 weeks. It's stalling out during idle like it isn't getting enough fuel to it. Brake and engine light on dash are staying on. Radio, interior lights won't come on. Will not come out of park once in. I have to do the old forward, back, middle key trick to get it out of park into neutral so I can start it and go. I've also checked all fuses and relays under dash and under Hood.
View 3 Replies
My fuel gauge indicates empty at all times. The first suggestion I received was to replace the sending unit in the gas tank. I did that but the gauge still indicates empty.
I tried the HEC Dealer test mode and I now know that FUEL reads 255. Which should be an 'open' state. The connector near the fuel tank does appear to be making good contact, so my suspicion is a broken wire somewhere between the rear of the truck and the front.
I tried following the wire on it's way towards the front of the truck, but I quickly loose sight of the wire as more branches enter into the wiring harness. Where does this wire end? Does it terminate in the engine compartment, at the instrument cluster, somewhere else?
I just can't figure out how to narrow down where the break in the wire might be. Or am I chasing down the wrong root cause?
View 1 Replies
Looking for a link to the fuel pump wiring for a 2000 V10 Ex? I'm trying to pinpoint my no start issue and want to make sure I don't miss anything. I think it goes from 20 amp fuse under hood to inertia switch to relay under hood to pump? 20 amp fuse has power but at the inertia switch I have no voltage, just approx 35 ohms resistance to ground on both outside wires. Does the inertia switch close a ground or should it have voltage?
View 10 Replies
