Ford Wiring/Electrical :: 1967 F100 - Instrument Cluster Gauge Wiring
Mar 4, 2015
I am a beginner when it comes to anything involving wiring. I am looking to re-wire all of the wiring coming off of the instrument cluster gauges. Once I have completed all of the wiring on the gauges, I may feel confident to move onto something else. As of rite now, it appears as though my truck is still running on all of the original wiring, and over the past few weeks, I have been having many wiring related issues. I found a schematic that includes the wiring for the gauges that I am going to go off of. I have a couple of questions before I begin.
1.) On the schematic, it shows connectors such as "Connector G" which is moving all of the gauges wires to there locations. Do I need to use a specific Ford connector, or could I purchase a new connector at any hardware store that carries them? As far as I am concerned, connectors do the same thing as all other connectors. (Let you connect and disconnect for easy instrument cluster removal.)
2.) I am not looking to purchase one of those expensive wiring harnesses. I would like to just purchase some wire that I can cut / use myself. What brand / type of wire should I be looking to purchase? I do not care if it is striped / colored as I will use wire tabs to name / label each wire.
Other than that, I feel confident enough to attempt something such as this. Here is the wiring schematic I am going to use.....
View 10 Replies
Advertisement
Looking for a source for a wiring diagram for the 2003/4 f350 instrument cluster, specifically the wiring/connectors to the gauges? A link to a PDF file would be nice. I would like to try and disconnect the PCM control to the transmission temperature and engine temperature and drive the gauges from my own sensors to bypass the non-linear behavior that ford decided was in our best interest. I am NOT interested in installing any more gauges, just want to control the ones already present with my own signals. It is possible that these gauges are all addressable devices on a common bus, instead of individual controls.
View 8 Replies
I'm about to dropkick my oil gauge but need to make sure that it is the problem. It WAS working but recently stopped. Here's what I have:
Dolphin electric oil gauge as part of their 6 gauge kit...fairly new oil sending unit (it's been on a year or so but the truck is not road worthy yet)....312 V8 and all of this is in a '53 F100.
I have verified, by hooking up a direct oil pressure gauge, that there is oil pressure. I have checked my wiring (it is all new from about a year ago) and it is all hooked up. My question is with the oil gauge removed, how can I hook up power to it and see if it works?
I could just go replace the sending unit but being that it is new I'm not going to throw parts at it just yet.
View 6 Replies
I have a 2008 Ford F-150 xlt with stock instrument cluster. I need a new instrument cluster due to my interior lights coming on while driving. I would like to make it look better and not go stock. Id like to have digital shift screen and good looking LED's. What all are my options?
View 2 Replies
The instrument cluster in my 2005 Mountaineer has been randomly "failing" for about 2 months. By "failing", I mean the gauges will go to zero and bounce, the dash lights will go on and off, and the radio will go out. The car will continue driving normally. Headlights stay on, windows work, cruise works, interior lights work. This random event lasts about 4 seconds. It may do it again within minutes, or not again for the day. Sometimes, when I open the car door to get in (keys not in ignition), I will notice the gauges are bouncing at the zero mark. I took it to the shop, but of course it didn't do it there. They checked the alternator and battery. Battery is old, but checked out. A few weeks later, complete Alternator failure. Replaced the battery and alternator and I hoped that would solve the dash issue, but it did not. I've had it to the dealership, and to an independent, and their not sure what's up with it. The code readers give no insight.
View 8 Replies
I am currently converting a 1999 E350 7.3 diesel bus into a camper to live in. The bus has already had a lot of weird custom work. Done by someone else and a lot of the interior torn out and extra insulation put in. There is an exposed electrical panel behind the drivers seat. It was a cheap buy, previously fleet maintained with only 120k.
I was hooking up a battery for accessories to a terminal labeled "Battery" that does run indeed directly to the + terminal of the battery in the engine compartment.
Unfortunately I mistakenly connected the accessory battery to a terminal labeled "ignition" that runs to behind the dash. When I tried starting the vehicle off the auxiliary battery for a test everything went out for 2 seconds, I heard a click from the engine compartment, and everything than came back on. This is when I realized my mistake.
It used to be the speedo only didn't work (which I assumed was the step motor), now after this mistake all the gauges, the odometer and the buzzers don't work. Lights like the battery and airbag warning indicator still function.
Checked fuse 2 (15 amp) for the instrument cluster and it is intact. Actually checked every fuse in the vehicle in both fuse panels and all are intact. The radio works though and the vehicle is not equipped with power windows.
Going to go get a radio removal tool to take apart the dash and get back there. What this could be? Did I fry a relay? Did I fry the cluster circuit board.
View 6 Replies
I have a 2003 F550 6L diesel flatbed truck. Last week, the overdrive button would activate by itself. I'm assuming there was a loose wire so I taped the button to keep the overdrive off. Two days later, the overdrive came on while the button was pressed in and then smoke came out of the steering column/lever area. I pulled over and turned off the truck. The smoke stopped after 10 seconds and I restarted the truck. The overdrive light/functionality no longer worked and the instrument cluster also wasn't working.
The next day I was driving, and the truck died at a stoplight. I got it towed home, and opened the steering column and noticed that the overdrive button wire had burned. I removed the harness clip and charged the batteries. It started but the instrument cluster still didn't work. 2 minutes later the truck died. I replaced the alternator but still it won't charge the batteries. The truck dies 2 mins after getting a battery boost to start the truck. The instrument cluster also doesn't work. What could be causing this issue?
View 10 Replies
I have a new 12 volt wiring harness in my 1953 f100. I had no problems with the truck running until recently. Here is what is happening. The engine will turn over just fine, but not crank. I am getting spark at the plugs. My ignition switch is new. Plugs are new. I have breakerless system in my distributor. I am wandering if it could be the voltage regulator causing this. Very frustrating.
View 2 Replies
Just got a 66 f100. Some one cut out the ignition. It has a toggle switch that doesn't seem to do anything, turned it to on and used a screwdriver to short the solenoid and it did not crank. I think I counted 9 cut wires in the area of the ignition counting 2 for the toggle. My other 61-66 trucks seem to just have five wires? So I can remove an ignition from one of these parts trucks, but might there be a difference since the gauges are unique to 1966 ?
Started to take the ignition out of my 62 f600 but i hate to cut wires but i must since there is no remnant of an ignition in the 66 f100. If I can match the five wires i should be ok. Just putting a battery in i have headlights, tailights and dash lights. Solenoid and cable to starter look horrible so i bought a new cable. I think i have a good solenoid or two? I didn't even get a spark when i shorted the solenoid with a screwdriver....
View 5 Replies
I have a fuel pump I want to install I want to hook this thing up on a switch inside the cabin to be used as kind of a security device, but I am hoping I can wire it into the ignition as well.... I want the pump to activate when the ignition is turned on but only if the (hidden from view) switch is in the "on" position. Not sure if all this is possible.
I have heard I ought to utilize a relay to avoid voltage loss at the pump. I have never hooked up a relay to anything before although I have heard of them being used. This system is being installed on a 1967 F250.
View 6 Replies
I have a 1976 Ford F100 with a 302 and my problem is sometimes when my engine is running and I try to cut it off, it continues to run and the only way to stop it is to jerk the coil wire off. This is an intermittent problem. Happens about every 6 or 7 times I drive it. I have replaced the ignition switch and still have the same problem. Pretty sure it is some type wiring or ground issue, just need someplace to start.
View 1 Replies
03 F250 Instrument panel does not work. Have checked all fuses with a meter. Have already fixed broken wires from the OD button on shifter handle. and also the alternator is not charging. I need wiring diagram that shows the wires coming out the back of the fuse box so I can see if the fuse holder is burned out......
View 8 Replies
For about 3 months, my wife's 2003 explorer has had a bad door sensor (I'm guessing). The car claims a door is ajar and the alarm would go off randomly if it's locked. Yesterday the battery died because apparently the alarm had been going off for so long while she was at work. After having a stranger jump it, she has had major problems:
-She claimed the headlights didn't work in any setting except in the on position with high beams on, but now they seem to work.
-The instrument panel is totally out including all gauges and all lights
-the power windows don't work
-the radio won't turn on or show any display
-the interior lights won't turn on
All of the fuses are fine and my mechanic checked them as well. He did say that a few key fuses aren't getting any power to them on either side. But the battery is charging and drawing just fine. The car doesn't seem to have any other issues and all of the flashers work just fine.
What the problem could be? I have wondered if one of the relays is busted.
View 3 Replies
I pumped gas at the local Chevron after noticing I was running just below a quarter tank this morning and immediately after turning the truck back on the instrument panel was dead. All other electric components worked fine (windows, headlights, signals, radio, etc.) Yukon GMC 2003 110k miles...
View 8 Replies
Any COMPLETE headlight switch wiring diagram? Everything I find online only shows 2-3 wires in each sub connector, nothing with all wires and colors, and what they do. and of course the factory service manuals no longer work on my new computer. the switch and associated wires went up in smoke 2 hours ago, and this truck is my only means of transportation rite now. what i need is headlight wiring with colors so i can temporary hook up a toggle switch to have lights until the new switch and connectors come in next week. I went to pull the switch and connectors out of the parts truck, but of course that does not have fog lights so it uses different switch and connections.
View 14 Replies
I plan on moving the engine/drivetrain from my 1986 F350 460 to my 1996 F250. I also want to move over the 1986's ignition system with a Duraspark 2 setup.
Although I could just cut in the easiest places to remove the wiring for later reuse I am looking for where to make the cuts, what to take and what to scrap. Alternatively I am also asking if there are aftermarket or OEM replacement sets out there are aren't a ton of money. The current harness in the 1986 has been sprayed with engine oil and cooked for 27 years so I am looking at alternative options if there are any.
View 8 Replies
I have a 97 F250 HD. Wiring the rear tail lights. When we bought it the had cut off the wires going to both sides of the rear lighting assemblys and I was wondering what wire went to what i have the left turn signal working just can't seem to get the brake/back up light to work on that side and i can't figure out how to get the right side going either.
View 8 Replies
Just bought an 04 Super duty with the factory plug 7pin and 4 pin plug. Checked the fuses and finally tracked down the 2 relays under the hood but can't seem to find anything wrong. Everything on the trailer works except for the running lights. Is there another fuse or something I have missed? Trailer works fine on my buddies Duramax and worked fine on my old 97.
View 14 Replies
Im installing a set of 04 lariat seats into a 00 truck. I need to know how to hook up the heat. The power part is no problem. What I thought was right which was a separate constant 12v and a switched 12v for the module and ground apparently isnt right. If somebody could ohm out their harness on a 01 truck that would be great. As I have it right now the light on the switch comes on but almost instantly turns off.
View 14 Replies
Looking for a wiring diagram for a F-150 XLT LARIAT 5.8L 4BBL, all the books I have looked at show the wiring for this year with fuel injection and this truck came with a 351W with a Holley 600 4BBL, I have a few wire's in the engine compartment that melted away all the insulation, they are located close to where the harness passes the firewall before the ignition module. Is this a common problem on old models ?. Need a clear copy of the correct diagram for a f-150 1987 with carburetor, how I can get a copy so I can fix this problem before it gets worse.
View 3 Replies
Let me start by saying electrical is something I really have no knowledge of....(never used any kind of an elec meter and don't have one) simple, Pos-grd and fuse, NP. I really don't want to fry something in these expensive new seats w/my normal trial and mostly ERROR!
The 08 (drivers) seat has 4 wires in the input clip.
GRN-RED (heavy gauge)
BLK-PURP (heavy gauge
BLU-RED
BLK-WHT
and my 01 whip out of the floor has a 3 wire setup.
GRN (heavy gauge)
BLK (heavy gauge)
BRN-BLU
I can wire PS side seat from fuse box and ground it NP. It only has a 2 wire set-up in the new seat.
View 1 Replies
