Ford Wiring/Electrical :: 1966 F100 - Ignition Totally Cut Out
Aug 6, 2015
Just got a 66 f100. Some one cut out the ignition. It has a toggle switch that doesn't seem to do anything, turned it to on and used a screwdriver to short the solenoid and it did not crank. I think I counted 9 cut wires in the area of the ignition counting 2 for the toggle. My other 61-66 trucks seem to just have five wires? So I can remove an ignition from one of these parts trucks, but might there be a difference since the gauges are unique to 1966 ?
Started to take the ignition out of my 62 f600 but i hate to cut wires but i must since there is no remnant of an ignition in the 66 f100. If I can match the five wires i should be ok. Just putting a battery in i have headlights, tailights and dash lights. Solenoid and cable to starter look horrible so i bought a new cable. I think i have a good solenoid or two? I didn't even get a spark when i shorted the solenoid with a screwdriver....
View 5 Replies
Advertisement
I am a beginner when it comes to anything involving wiring. I am looking to re-wire all of the wiring coming off of the instrument cluster gauges. Once I have completed all of the wiring on the gauges, I may feel confident to move onto something else. As of rite now, it appears as though my truck is still running on all of the original wiring, and over the past few weeks, I have been having many wiring related issues. I found a schematic that includes the wiring for the gauges that I am going to go off of. I have a couple of questions before I begin.
1.) On the schematic, it shows connectors such as "Connector G" which is moving all of the gauges wires to there locations. Do I need to use a specific Ford connector, or could I purchase a new connector at any hardware store that carries them? As far as I am concerned, connectors do the same thing as all other connectors. (Let you connect and disconnect for easy instrument cluster removal.)
2.) I am not looking to purchase one of those expensive wiring harnesses. I would like to just purchase some wire that I can cut / use myself. What brand / type of wire should I be looking to purchase? I do not care if it is striped / colored as I will use wire tabs to name / label each wire.
Other than that, I feel confident enough to attempt something such as this. Here is the wiring schematic I am going to use.....
View 10 Replies
I have a new 12 volt wiring harness in my 1953 f100. I had no problems with the truck running until recently. Here is what is happening. The engine will turn over just fine, but not crank. I am getting spark at the plugs. My ignition switch is new. Plugs are new. I have breakerless system in my distributor. I am wandering if it could be the voltage regulator causing this. Very frustrating.
View 2 Replies
I'm about to dropkick my oil gauge but need to make sure that it is the problem. It WAS working but recently stopped. Here's what I have:
Dolphin electric oil gauge as part of their 6 gauge kit...fairly new oil sending unit (it's been on a year or so but the truck is not road worthy yet)....312 V8 and all of this is in a '53 F100.
I have verified, by hooking up a direct oil pressure gauge, that there is oil pressure. I have checked my wiring (it is all new from about a year ago) and it is all hooked up. My question is with the oil gauge removed, how can I hook up power to it and see if it works?
I could just go replace the sending unit but being that it is new I'm not going to throw parts at it just yet.
View 6 Replies
I have a 1976 Ford F100 with a 302 and my problem is sometimes when my engine is running and I try to cut it off, it continues to run and the only way to stop it is to jerk the coil wire off. This is an intermittent problem. Happens about every 6 or 7 times I drive it. I have replaced the ignition switch and still have the same problem. Pretty sure it is some type wiring or ground issue, just need someplace to start.
View 1 Replies
I plan on moving the engine/drivetrain from my 1986 F350 460 to my 1996 F250. I also want to move over the 1986's ignition system with a Duraspark 2 setup.
Although I could just cut in the easiest places to remove the wiring for later reuse I am looking for where to make the cuts, what to take and what to scrap. Alternatively I am also asking if there are aftermarket or OEM replacement sets out there are aren't a ton of money. The current harness in the 1986 has been sprayed with engine oil and cooked for 27 years so I am looking at alternative options if there are any.
View 8 Replies
I have a 2007 e350. I installed a battery isolator and I believe I need to run a wire from the ignition circuit to the exciter post on the isolator. I found the Power Distribution Panel under the hood (drivers side) which has a fuse in slot #7 (60 amp Maxi Fuse) listed as Ignition Switch/Accessory Delay. What is the best way to tap into this?
Also, I have 8 gauge wire which I ran from the isolator to the batteries. I am second guessing this now and wondering if I should go with thicker wire?
View 5 Replies
Pulled up to customers home and took key out and engine kept running. Disconnected battery, engine and aux turned off. Then Connected battery and power came on as if the key was in. Then put key in and turned with no change in power or engine trying to turn. Disc battery, put key in first then connected battery and truck started. Last stop took key out as well as disc batt and engine stayed on this time. repeated steps above several times to get back. Looking for narrowing the problem,possible ignition key cylinder, actuator or possible bad circuit.
View 4 Replies
I have a 77 ford truck with a 351 ,the ignition system keeps shorting out, killing spark. If i replace the starter solenoid, it works for a while, then goes out again. I have replaced 4 solenoids this month. What could be shorting the solenoid out? Had the truck for 8 yrs. now, never had a problem with it till now. It has a mallory dist. it was in when i bought it.
View 7 Replies
I bought a 1952 F1 that is mounted on a 1978 E350 chassis.( 351W )
It has all the 78 wiring installed. When cranking engine, it will not start, unless you release key to run position. You have to get engine turning over, and then quickly release key to start. Checked back of switch, not losing voltage at ignition post while cranking...
View 5 Replies
My 77 F150 Ranger with a 400 in it didn't wanna start up at all. It wouldn't even crank or click like if the battery was dead. Then I tried again this morning and it cranked once then melted a red wired with I think a black or gray tracer, on the ignition. (I put a new solenoid on a couple months back and the positive also melted a bit by the solenoid but didn't pay any attention to it.) I'm just wondering what could be wrong with it to make it do that and how to fix it. Also when I went to put gas in it (it's on a slight hill making it lean to the driver side) it was empty but no fuel would go down the filler neck, then it started to gurgle and spit it out some. I was told it was vapor lock but I thought vapor lock happens when it's hot.
View 3 Replies
Having problems with their door locks attempting to activate when turning the ignition key? If so, how can I correct it or make repairs.
View 4 Replies
here its is i have a 1986 ford f350 6.9 aftermarket turbo set up i was driving it then i went over rail road tracks lost all power to fuse box no headlights no interior lights no ignition power batteries are good so now when i turn key nothing lights up it just killed my whole truck....
View 7 Replies
So my Honda Civic has been flashing my check engine light, which is telling my my cylinders are misfiring. I checked the ignition coils by removing them while the car was running and cylinder 2 and 3 I can remove and it doesn't change how the car runs. I put a new ignition coil In and that doesn't work so it isn't the ignition coils, what it could be?
View 8 Replies
Our Honda Odyssey will have an occasional delayed start where you turn the key but no sound occurs. All the lights come on like normal and the automatic doors can all close and open without any issues. Originally we didn't know that we could eventually get the car to start by turning and holding the key in the start position. It happens every couple days to couple weeks and without holding the key in the on position it will be anywhere from 30 minutes to 3 days before the car will start normally again. We've spent about $1,000 at the Honda dealer to have the battery, battery cables, starter, and starter relay replaced but we're still having the problem.
View 2 Replies
Blower, seats, locks, blinkers stopped simultaneously, abs and airbag light came on. The internet suggested it was the ignition switch, I changed it to no avail. The horn, wipers, 4-way flashers, headlights, taillights, and brake lights all work. Is my wife correct in suggesting we replace this 140,000 mile pile of rust?
View 5 Replies
Any COMPLETE headlight switch wiring diagram? Everything I find online only shows 2-3 wires in each sub connector, nothing with all wires and colors, and what they do. and of course the factory service manuals no longer work on my new computer. the switch and associated wires went up in smoke 2 hours ago, and this truck is my only means of transportation rite now. what i need is headlight wiring with colors so i can temporary hook up a toggle switch to have lights until the new switch and connectors come in next week. I went to pull the switch and connectors out of the parts truck, but of course that does not have fog lights so it uses different switch and connections.
View 14 Replies
I have a 97 F250 HD. Wiring the rear tail lights. When we bought it the had cut off the wires going to both sides of the rear lighting assemblys and I was wondering what wire went to what i have the left turn signal working just can't seem to get the brake/back up light to work on that side and i can't figure out how to get the right side going either.
View 8 Replies
Looking for a source for a wiring diagram for the 2003/4 f350 instrument cluster, specifically the wiring/connectors to the gauges? A link to a PDF file would be nice. I would like to try and disconnect the PCM control to the transmission temperature and engine temperature and drive the gauges from my own sensors to bypass the non-linear behavior that ford decided was in our best interest. I am NOT interested in installing any more gauges, just want to control the ones already present with my own signals. It is possible that these gauges are all addressable devices on a common bus, instead of individual controls.
View 8 Replies
Just bought an 04 Super duty with the factory plug 7pin and 4 pin plug. Checked the fuses and finally tracked down the 2 relays under the hood but can't seem to find anything wrong. Everything on the trailer works except for the running lights. Is there another fuse or something I have missed? Trailer works fine on my buddies Duramax and worked fine on my old 97.
View 14 Replies
Im installing a set of 04 lariat seats into a 00 truck. I need to know how to hook up the heat. The power part is no problem. What I thought was right which was a separate constant 12v and a switched 12v for the module and ground apparently isnt right. If somebody could ohm out their harness on a 01 truck that would be great. As I have it right now the light on the switch comes on but almost instantly turns off.
View 14 Replies
